Home > Dell > Notebook > Dell Inspiron 2500 Parts Manual

Dell Inspiron 2500 Parts Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Dell Inspiron 2500 Parts Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 327 Dell manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							Removing and Replacing Parts93
      NOTICE: When reconnecting the flex cable, press down on both ends of the 
    connector, not in the middle. Pressing the middle of the connector can damage 
    fragile components.
    3
    Open the display and remove the two screws (marked with a “circle 
    D”) that secure the display assembly to the bottom case assembly.
    4With the display in an upright position, lift the display assembly from 
    the bottom case assembly.
    6-mm screw 
    strain relief pull loop
    flex cable 
    						
    							94Removing and Replacing Parts
    www.dell.com | support.dell.com
    Display Assembly Bezel and Panel
    12.1-Inch Display Bezel
    display
    panel
    top cover flex cable4-mm screws (6)
    bezel 
    latch ru
    bber screw covers (4)
    plastic screw
    covers (2)display assembly bezel 
    						
    							Removing and Replacing Parts95
    14.1-Inch Display Bezel 
     NOTICE: Disconnect the computer and attached devices from electrical 
    outlets and remove any installed battery.
      NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or 
    by periodically touching an unpainted metal surface on the computer.
    display
    panel
    top cover flex cable4-mm screws (6)
    bezel 
    latch ru
    bber screw covers (4)
    plastic screw
    covers (2)display assembly bezel 
    						
    							96Removing and Replacing Parts
    www.dell.com | support.dell.com
    Removing the Display Assembly Bezel
    1Follow the instructions in Preparing to Work Inside the Computer.”
    2Use a scribe to pry loose the four rubber screw covers located across the 
    top of the bezel. 
    3Remove the two 4-mm screws located across the top of the bezel.
    4Use a scribe at the indentations to pry loose the plastic screw covers 
    located at the bottom of the bezel. 
    5Remove the six 4-mm screws located at the bottom of the bezel.
    6Separate the bezel from the display-assembly top cover. 
    The bezel is secured to the display assembly top cover with plastic tabs 
    around the sides. Use a plastic scribe to help separate the bezel from 
    the top cover.
    Removing the Display Panel
    1Remove the hinge cover.
    2Remove the screw securing the flex cable to its strain relief, and then 
    use the pull loop to remove the flex cable from the system board. 
    						
    							Removing and Replacing Parts97
     NOTICE: When reconnecting the flex cable, press down on both ends of the 
    connector, not in the middle. Pressing the middle of the connector can damage 
    fragile components.
    3
    Remove the display assembly bezel.
    4Remove the 4-mm screw securing the plastic flex-cable mounting 
    bracket to the top cover assembly.
    5Remove the four 3-mm screws (two on each side) from the right and 
    left sides of the panel.
    6Lift the display panel and flex cable out of the top cover assembly. 
    7Disconnect the flex cable from the two connectors (a ZIF and a 
    standard connector) on the display panel assembly.
    6-mm screw 
    strain relief pull loop
    flex cable 
    						
    							98Removing and Replacing Parts
    www.dell.com | support.dell.com
     HINT: If you find a 
    kaption tape on the 
    standard connector, 
    remove it.
    Replacing the Display Panel
     HINT: Use a magnetic 
    screwdriver to reassemble 
    the display panel in the 
    display.1Connect the flex cable to the two connectors (ensure that the ZIF 
    connector is locked into place) on the back of the display panel.
    2Place the display panel assembly in the top cover, taking care that the 
    flex cable is in place and is not crushed or crimped.
    3Reinstall the 4-mm screw that secures the flex-cable mounting bracket 
    to the top cover.
    ZIF connector
    standard connector
    inverter board
    panel 
    						
    							Removing and Replacing Parts99
    4Starting on the left side, use a magnetic screwdriver to reinstall the 
    four 3-mm screws that secure the display panel in the top cover.
    5Reinstall the display assembly bezel.
    15-Inch Display Assembly
    display
    panel
    top cover flex cable4-mm screws (6)
    bezel 
    latch rubber screw covers (4)
    plastic screw
    covers (2)
    3-mm screws (6)display assembly bezel
    plastic 
    tabs (6) 
    						
    							100Removing and Replacing Parts
    www.dell.com | support.dell.com
      NOTICE: Disconnect the computer and attached devices from electrical 
    outlets and remove any installed battery.
      NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or 
    by periodically touching an unpainted metal surface on the computer.
    Removing the Display Assembly Bezel
    1Follow the instructions in Preparing to Work Inside the Computer.”
    2Use a scribe to pry loose the four rubber screw covers located across the 
    top of the bezel. 
    3Remove the four 4-mm screws located across the top of the bezel.
    4Use a scribe at the indentations to pry loose the plastic screw covers 
    located at the bottom of the bezel. 
    5Remove the two 4-mm screws located at the bottom of the bezel.
    6Separate the bezel from the display-assembly top cover. 
    The bezel is secured to the display assembly top cover with plastic tabs 
    around the sides. Use a plastic scribe to help separate the bezel from 
    the top cover.
    Removing the Display Panel
    1Remove the hinge cover.
    2Remove the screw securing the flex cable to its strain relief, and then 
    use the pull loop to remove the flex cable from the system board. 
    						
    							Removing and Replacing Parts101
      NOTICE: When reconnecting the flex cable, press down on both ends of the 
    connector, not in the middle. Pressing the middle of the connector can damage 
    fragile components.
    3
    Remove the display assembly bezel.
    4Remove the 4-mm screw securing the plastic flex-cable mounting 
    bracket to the top cover assembly.
    5Remove the six 3-mm screws (three on each side) from the right and 
    left sides of the panel.
    6Lift the display panel and flex cable out of the top cover assembly. 
     HINT: If you find a 
    kaption tape on the 
    standard connector, 
    remove it. 7Disconnect the flex cable from the two connectors (a ZIF and a 
    standard connector) on the display panel assembly.
    6-mm screw 
    strain relief pull loop
    flex cable 
    						
    							102Removing and Replacing Parts
    www.dell.com | support.dell.com
    Replacing the Display Panel
     HINT: Use a magnetic 
    screwdriver to reassemble 
    the display panel in the 
    display.1Connect the flex cable to the two connectors (ensure that the ZIF 
    connector is locked into place) on the back of the display panel.
    2Place the display panel assembly in the top cover, taking care that the 
    flex cable is in place and is not crushed or crimped.
    3Reinstall the 4-mm screw that secures the flex-cable mounting bracket 
    to the top cover.
    ZIF connector
    standard connectorinverter board
    panel 
    						
    All Dell manuals Comments (0)

    Related Manuals for Dell Inspiron 2500 Parts Manual