Dell In1920 Users Guide

   
   
   
See  Solving Problems  for more information.  
Setting the Maximum Resolution  
To set the Maximum resolution for the monitor:  
1. Right - click on the desktop and select  Properties .   
2. Select the  Settings  tab.   
3. Set the screen resolution to 1440 x 900 (for IN1720) or 1366 x 768 (for IN1920).   
4. Click  OK .   
If you do not see 1440 x 900 (for IN1720 only) or 1366 x 768 (for IN1920 only) as an option, you may need to update your graphics card driver. Depending on 
your...

The Dell Soundbar is a stereo two channel system, mountable on Dell Flat Panel Displays.  The Soundbar has a rotary volume and on/off control to adjust the 
overall system level, a LED for power indication, and two audio headset jacks.  
 
   
Using the Tilt  
Tilt  
With the stand assembly, you can tilt the monitor for the most comfortable viewing angle.  
 
 
Back to Contents Page  1. Power ON/volume control
2.  Power indicator
3.  Headphone connectors 
NOTE:  The stand base is detached when the...

Back to Contents Page   
Setting Up Your Monitor   
 
IN1720/IN1920  Flat Panel Monitor   
Setting the display resolution to  1440 x 900 (for IN1720) or 1366 x 768 (for 
IN1920) ( Maximum)  
For optimal display performance while using the Microsoft Windows operating systems, set the display resolution to 1440 x 900 (for IN1720) or 1366 x 768 (for 
IN1920) pixels by performing the following steps:  
1. Right - click on the desktop and click  Properties .  
2. Select the  Settings  tab.  
3. Move the...

IN1720/IN1920  
Information in this document is subject to change without notice.  
2010  
Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc.   is strictly forbidden.  
Trademarks used in this text:  Dell  and the  DELL  logo are trademarks of Dell Inc.;   Microsoft and Windows  are either registered trademarks or trademarks of Microsoft Corporation in 
the United States and/or other countries. ENERGY STAR  is a registered trademark of the U.S....

Back to Contents Page    
 
Setting Up the Monitor   
IN1720/IN1920  Flat Panel Monitor Users Guide  
   Attaching the Stand  
   Connecting Your Monitor  
   Removing the Stand Base     
   Attaching the Dell Soundbar (Optional)  
   Removing the Stand for VESA wall mount  
   
Attaching the Stand  
 
 
   
Connecting Your Monitor  
To connect your monitor to the computer:  
1. Turn off your computer and disconnect the power cable.   
2. Connect the blue display connector cable to the corresponding...

 
Removing the Stand Base   
    CAUTION:  The graphics are used for the purpose of illustration only. Appearance on the computer may vary.
IN1720:  
 
   
IN1920:    
   

Attaching the Dell Soundbar(for IN1920 only)  
 
To attach the soundbar:  
Removing the Stand for VESA Wall Mount  
IN1720:  
 
   
IN1920:  To remove stand base from the monitor:  
1. Place the monitor panel on soft cloth or cushion on a stable flat table.  
2. Press and hold the release latch, while pulling the stand base away from the monitor.
NOTICE:  Do not use with any device other than the Dell Soundbar. 
1.  Working from the back of the monitor, attach Soundbar by aligning the two slots with the...

 
   
Back to Contents Page    
    To remove the stand assembly from the monitor:
1. Place the monitor panel on soft cloth or cushion on a stable flat table.
2. Remove the three screws on the stand of the monitor as shown above.
3. Remove the stand assembly from the monitor.  

Back to Contents Page    
 
Troubleshooting  
 
IN1720/IN1920  Flat Panel Monitor   
   Self - Test  
   Common Problems  
   Product Specific Problems  
   
Self - Test  
Your monitor provides a self - test feature that allows you to check whether your monitor is functioning properly. If your monitor and computer are properly 
connected but the monitor screen remains dark, run the monitor self - test by performing the following steps:   
1. Turn off both your computer and the monitor.   
2. Unplug the...

To run the built - in diagnostics:  
1. Ensure that the screen is clean (no dust particles on the surface of the screen).   
2. Unplug the video cable from the back of the computer or monitor. The monitor then goes into the self - test mode.   
3. Press and hold the 1st and 4th buttons on the front panel, simultaneously for 2 seconds. A gray screen appears.   
4. Carefully inspect the screen for abnormalities.   
5. Press the 4th button on the front panel again. The color of the screen changes to red....