Dell E2011h Users Guide

							 
Notes, Notices, and Cautions  
   
   
   
 
Information in this document is subject to change without notice.  
 
Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc.   is strictly forbidden.  
Trademarks used in this text:  Dell  and the  DELL  logo are trademarks of Dell Inc;   Microsoft  and  Windows  are either trademarks or registered trademarks of Microsoft Corporation in 
the United States and/or other countries ,  Intel  is a registered trademark of Intel Corporation in the U.S. and other countries; and ATI is a trademark of Advanced Micro Devices, 
Inc.  ENERGY STAR is a registered trademark of the U.S. Environmental Protection Agency. As an ENERGY STAR partner, Dell Inc. has determined that this product meets the 
ENERGY STAR guidelines for energy efficiency.  
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any 
proprietary interest in trademarks and trade names other than its own.  
Model E2011Ht, E2011Hc.   
 
June 2010 Rev. A00   About Your Monitor  
 
Setting Up the Monitor  
 
Operating the Monitor  
Troubleshooting   
Appendix  
     
NOTE:  A NOTE indicates important information that helps you make better use of your monitor. 
CAUTION:   A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.
 
WARNING:  A WARNING indicates a potential for property damage, personal injury or death.  
						

							Back to Contents Page    
 
About Your Monitor   
 
Package Contents    
Your monitor ships with the components shown below. Ensure that you have received all the components and  contact Dell  if something is missing.  Package Contents
Product Features
Identifying Parts and Controls
Monitor Specifications
Plug and Play Capability
LCD Monitor Quality and Pixel Policy
Maintenance Guidelines
  NOTE:  Some items may be optional and may not ship with your monitor. Some features or media may not be available in certain countries.
  NOTE:  To set up with an y  other stand, please refer to the  respective  stand setup guide for setup instructions.
  l Monitor  
l Stand  
  l Power Cable  
  l VGA Cable    
						

							     
Product Features  
The   flat panel display has an active matrix, thin - film transistor (TFT), liquid crystal display (LCD), and LED backlight. The monitor features 
include:  
■  50.8 cm (20 - inchyfYLHZDEOHDUHDGLVSOD\0HDVXUHGGLDJRQDOO\\f.   1600 X 900  resolution, plus full - screen support for lower resolutions.   
■  Tilt adjustment capability.  
■  Removable pedestal and Video Electronics Standards Association (VESA ) 100 mm mounting holes for flexible mounting solutions.   
■  Plug and play capability if supported by your system.   
 
■  On - Screen Display (OSD) adjustments for ease of set - up and screen optimization.   
 
■  Software and documentation media includes an information file (INF), Image color Matching File (ICM), PowerNap software application and product 
documentation.   
 
■  Energy Saver feature for Energy Star compliance.   
■  Security lock slot.  
■  Asset Management Capability.   
■  Capability to switch from wide aspect to standard aspect ratio while maintaining the image quality.   
■  EPEAT Gold Rating.  
■   Halogen Reduced .  
■  Arsenic - Free glass and Mercury Free for Panel only.  
■  Energy Gauge shows the energy level being consumed by the monitor in real time.  
■  PowerNap Software included (comes in the CD attached with the monitor).  
Identifying Parts and Controls  
Front View     l DVI Cable  
  l Drivers and Documentation  media   
l Quick Setup Guide    
l Product and Safety Information Guide    
						

							Back View  
 
Side View  Front View   Front panel controls
Label Description
1 Preset Modes (default, but configurable)
2 Brightness & Contrast (default, but configurable)
3 Menu
4 Exit
5 Power button  (with power light indicator)
Back view   Back view with monitor stand  
Label   Description   Use  
1   VESA mounting holes   (100 mm x 100 mm  -  
behind attached  VESA Plate ) Wall mount monitor using VESA - compatible wall mount kit (100 mm x 100 mm).   
2   Regulatory label Lists the regulatory approvals.
3   Stand release button  Release stand from monitor. 
4   Security lock slot   Secures monitor with security cable lock.   
5   Dell Soundbar mounting brackets Attaches the optional Dell Soundbar.
6   Barcode serial number label Refer to this label if you need to contact Dell for technical support.
7 Cable  management  slot Use to organize cables by placing them through the slot.  
						

							Bottom View    
Monitor Specifications  
Flat Panel Specifications   
Left view     Right view  
Bottom view    
Label Description Use
1   AC power connector   To connect the monitor power cable.  
2 VGA connector  To connect your computer to the monitor using a VGA cable. 
3 DVI connector To connect your computer to the monitor using a DVI cable.
4   Stand lock  
To disable the stand release button and lock the stand assembly 
using an M3 machine screw.
Model E2011H
Screen type Active matrix  -   TFT LCD
Panel type  TN
Screen dimensions 50.8 cm  (20 - inches viewable image size)
Preset display area 462.8  (H) x  272. 0  (V) mm
Horizontal 462.8  mm (18.22 inches)
Vertical 272. 0  mm (10.71 inches)
Pixel pitch 0.277 mm
Viewing angle 160° (verticalyfW\S
						

							*[E2011H] color gamut (typical) is based on CIE1976 (79 % ) and CIE1931 (68%) test standards.   
Resolution  Specifications  
Video Supported Modes  
Preset Display Modes  
Electrical  Specifications  
Physical  Characteristics  Color gamut (Typical)    79%* (CIE1976)
Model E2011H
Horizontal scan range 30 kHz to 83 kHz (automatic)  
Vertical scan range 56 Hz to 75 Hz (automaticyf  
M aximum resolution 1600 X 900 at 60 Hz  
Model E2011H
Video display capabilities (DVI playback)
480p, 576p, 720p,   1080p  and 1080i
Display Mode   Horizontal Frequency 
(kHz)   Vertical Frequency 
(Hz)   Pixel Clock 
(MHz)   Sync Polarity 
(Horizontal/Vertical)  
720 x 400 31.5   70.0   28.3   - /+  
640 x 480  31.5   60.0   25.2   - / -  
640 x 480 37.5   75.0   31.5   - / -  
800 x 600 37.9   60.0   40.0   +/+  
800 x 600 46.9   75.0   49.5   +/+  
1024 x 768 48.4   60.0   65.0   - / -  
1024 x 768 60.0   75.0   78.8   +/+  
1152 x 864 67.5   75.0   108.0   +/+  
1280 x 1024 64.0   60.0   108.0   +/+  
1280 x 1024 80.0   75.0   135.0   +/+  
1600 x 900 60.0   60.0   97.8   +/ -  
Model E2011H
Video input signals Analog RGB, 0.7 Volts +/ - 5%, positive polarity at 75 ohm input impedance  
Digital DVI - D TMDS, 600mV for each differential line, positive polarity at 50 
ohm input impedance
Synchronization input signals Separate horizontal and vertical synchronizations, polarity - free TTL level, 
SOG (Composite SYNC on green)
AC input voltage/frequency/current 100 to 240 VAC/50 or 60 Hz  +  3 Hz/1.5 A (Max.)
Inrush current 120V:30A (Max.)  
240V:60A (Max.) 
Model E2011H
Connector type 15 - pin D - subminiature, blue connector; DVI - D, white 
connector
Signal cable type Digital: Detachable, DVI - D, Solid pins, shipped 
detached from the monitor 
Analog: Detachable, D - Sub, 15 pins, shipped attached 
to the monitor  
Dimensions (with stand)
Height
362.50 mm (14.27 inches)
Width
481.51 mm (18.96 inches)
Depth
151.70 mm (5.97 inches)
Dimensions (without stand)
Height 
287.61 mm (11.32 inches)  
						

							Environmental  Characteristics  
Power Management Modes  
If you have VESA's DPM™ compliance display card or software installed in your PC, the monitor can automatically reduce its power consumption when not in 
use. This is referred to as  Power Save Mode *. If the computer detects input from keyboard, mouse, or other input devices, the monitor automatically resumes 
functioning. The following table shows the power consumption and signaling of this automatic power saving feature:   
The OSD will only function in the normal operation mode. When any button is pressed in Active - off mode, the following message will be displayed:   
 
Activate the computer and the monitor to gain access to the  OSD.  
* Zero power consumption in OFF mode can only be achieved by disconnecting the main cable from the monitor.  Width
481.51 mm (18.96 inches)
Depth
60.00 mm (2.36 inches)
Stand dimensions
Height
291.66 mm (11.48 inches)
Width
251.10 mm (9.89 inches) 
Depth
151.70 mm (5.97 inches)
Weight
Weight with packaging
5.50 kg (12.13 lb)
Weight with stand assembly and cables
4.42 kg (9.73 lb)
Weight without stand assembly  
(For wall mount or VESA mount 
considerations  -   no cables) 2.90 kg (6.38 lb)
Weight of stand assembly 1.11 kg (2.45 lb) 
Model E2011H
Temperature
Operating 0° to 40 ° C 
Non - operating Storage:  - 20° to 60°C ( - 4° to 140°Fyf  
Shipping:  - 20° to 60°C ( - 4° to 140°Fyf
Humidity
Operating 10% to 80% (non - condensing)
Non - operating Storage: 5% to 90% (non - condensing)  
Shipping: 5% to 90% (non - condensing)
Altitude
Operating 4,850 m (15,902 ft) max
Non - operating 12,192 m (40,000 ft) max
Thermal dissipation 85.30 BTU/hour (maximum)  
61.42 BTU/hour (typical)
VESA Modes Horizontal Sync Vertical Sync  Video Power Indicator Power Consumption
Normal operation Active Active Active  Blue 18 W (typical)/25 W (maximum)
Active - off mode Inactive Inactive Blanked Amber Less than 0.5 W
Switch off - - - Off Less than 0.5 W
NOTE:  This monitor is  ENERGY STAR ®
- compliant.   
						

							Pin Assignments  
VGA Connector  
 
 
 Pin 
Number 15 - pin Side of the Co nnected Signal 
Cable
1 Video - Red  
2 Video - Green
3 Video - Blue
4 GND
5 Self - test
6 GND - R
7 GND - G
8 GND - B
9 Computer 5V/3.3V
10 GND - sync
11 GND
12 DDC data
13 H - sync
14 V - sync
15 DDC clock
Pin 
Number 24 - pin Side of th e C o nnected  Signal 
Cable
1 TMDS RX2 -
2 TMDS RX2+
3 TMDS Ground
4 Floating
5 Floating
6 DDC Clock
7 DDC Data
8 Floating
9 TMDS RX1 -
10 TMDS RX1+
11 TMDS Ground
12 Floating
13 Floating
14 +5V/+3.3V power  
						

							Plug and Play Capability  
You can install the monitor in any Plug and Play - compatible system. The monitor automatically provides the computer system with its Extended Display 
Identification Data (EDID) using Display Data Channel (DDC) protocols so the system can configure itself and optimize the monitor settings. Most monitor 
installations are automatic; you can select different settings if desired. For more information about changing the monitor settings, see  Operating the Monitor .  
               
LCD Monitor Quality and Pixel Policy  
During the LCD Monitor manufacturing process, it is not uncommon for one or more pixels to become fixed in an unchanging state which are hard to see and 
do not affect the display quality or usability. For more information on Dell Monitor Quality and Pixel Policy, see Dell Support site at:  support.dell.com .  
Maintenance Guidelines  
Cleaning Your Monitor  
For best practices, follow the instructions in the list below while unpacking, cleaning, or handling your monitor:  
l To clean your antistatic screen, lightly dampen a soft, clean cloth with water. If possible, use a special screen - cleaning tissue or solution suitable for the 
antistatic coating. Do not use benzene, thinner, ammonia, abrasive cleaners, or compressed air.   
l Use a lightly - dampened, warm cloth to clean the monitor. Avoid using detergent of any kind as some detergents leave a milky film on the monitor.    
l If you notice white powder when you unpack your monitor, wipe it off with a cloth.   
l Handle your monitor with care as dark - colored monitors may scratch and show white scuff marks more than light - colored monitors.   
l To help maintain the best image quality on your monitor, use a dynamically changing screen saver and turn off your monitor when not in use.   
     
             
Back to Contents Page    15 Self test 
16 Hot Plug Detect
17 TMDS RX0 -
18 TMDS RX0+
19 TMDS Ground
20 Floating
21 Floating
22 TMDS Ground
23 TMDS Clock+
24 TMDS Clock -
WARNING:  Read and follow the  safety instructions
WARNING:  
						

							Back to Contents Page    
 
Appendix   
 
  Safety Instructions  
  FCC Notice (U.S. Only) and Other Regulatory Information   
  Contacting Dell  
   
WARNING: Safety Instructions  
For information on safety instructions, see the  Product Information Guide .   
FCC Notices (U.S. Only) and Other Regulatory Information  
For FCC notices and other regulatory information, see the regulatory compliance website located at: http://www.dell.com/regulatory_compliance.  
Contacting Dell  
For customers in the United States, call 800 - WWW - DELL (800 - 999 - 3355).  
Dell provides several online and telephone - based support and service options. Availability varies by country and product, and some services may not be 
available in your area. To contact Dell for sales, technical support, or customer service issues:  
 
Back to Contents Page  WARNING:  Use of controls, adjustments, or procedures other than those specified in this documentation may result in exposure to shock, 
electrical hazards, and/or mechanical hazards. 
NOTE:  If you do not have an active Internet connection, you can find contact information on your purchase invoice, packing slip, bill, or Dell product catalog. 
1. Visit  support.dell.com . 
2.  Verify your country or region in the  Choose A Country/Region  drop - down menu at the bottom of the page.  
3. Click  Contact Us  on the left side of the page.
4. Select the appropriate service or support link based on your need.
5.  Choose the method of contacting Dell that is convenient for you.