Dell E177fp Users Guide

  Phase If satisfactory results are not obtained using the  Phase  adjustment, use the  Pixel Clock adjustment and then use Phase again.  
 
  NOTE: This function may change the width of the display image. Use the 'Horizontal' function of the 'Position' menu to center 
the display image on the screen.  
    Color 
Settings:   Adjusts the color temperature and saturation.  
 
    Normal Preset Selected to obtain the default (factory) color settings.  
    Blue Preset This color setting...

Automatic Save  
With the OSD open, if you make an adjustment and then either proceed to another menu, or exit the OSD, the monitor automatically saves any adjustments 
you have made. If you make an adjustment and then wait for the OSD to disappear the adjustment will also be saved.  
Reset  Functions  
Factory Preset Restoration         
 
  NOTE: When the OSD is locked, pressing the Menu button will take the user directly to the OSD settings menu, with OSD 
Lock preselected on entry. Select No( - ) to...

OSD Warning Messages  
A warning message may appear on the screen indicating that the monitor is out of sync.  
 
This means that the monitor cannot synchronize with the signal that it is receiving from the computer. Either the signal is too high or too low for the monitor to 
use. See  Specifications  for the Horizontal and Vertical frequency ranges addressable by this monitor. Recommended mode is 1280 X 1024 @ 60Hz.  
 
Occasionally, no warning message appears, but the screen is blank. This could also...

Soundbar Attachment to the Monitor  
   
 
Back to Contents Page  2. Power indicator 
3. Power/Volume control
1. Working from the rear of the monitor, attach the Soundbar aligning the two slots with the two tabs along the bottom rear of the monitor.
2. Slide the Soundbar to the left until it snaps into place.
3. Connect the Soundbar with the power brick.
4. Plug the power cables of the power brick into a nearby outlet. 
5. Insert the lime - green mini stereo plug from the rear of the Soundbar into the...

Back to Contents Page    
 
Product Specific Problems  
 
   Monitor Specific Troubleshooting   
  Common Problems  
  Product Specific Problems  
   
Monitor Specific Troubleshooting  
Self - Test Feature Check (STFC)  
Your monitor provides a self - test feature that allows you to check whether your monitor is functioning properly. If your monitor and computer are properly 
connected but the monitor screen remains dark, run the monitor self - test by performing the following steps:   
1. Turn off both...

Product Specific Problems   l Adjust Phase and Clock controls through OSD   
l Perform monitor reset   
l Check environmental factors   
l Relocate and test in  another  room   
Missing Pixels LCD screen has spots l Cycle power on - off   
l These are pixels that are permanently off and is a natural defect that occurs in LCD 
technology   
Stuck - on Pixels LCD screen has bright spots l Cycle power on - off   
l These are pixels that are permanently on and is a natural defect that occurs in LCD...

Back to Contents Page   signal  will 
appear.
No Input Signal when 
user controls pressed No picture, 
the LED light 
is green. 
When press 
+,  -  or 
Menu key, 
the message 
 No input 
signal  will 
appear. l Check the signal source Make sure the Computer is not in power saving by moving mouse or 
pressing any key on the keyboard.   
l Check whether the signal cable is plugged in and seated properly.  Re - plug the signal cable if 
necessary.   
l Re - boot the computer or video player.   
OSD Lock...

Back to Contents Page  
   
Using Your Monitor Stand   
DellT E177FP Flat Panel Monitor Users Guide   
  Attaching the Stand  
  Organizing Your Cables  
  Using the Tilt  
  Removing the Stand  
Attaching the Stand  
 
1. Place the stand on a flat surface.   
2. Fit the groove on the back of the monitor onto the two teeth of the upper stand.   
3. Lower the monitor so that the monitor mounting area snaps on/locks to the stand.  
Organizing Your Cables  
 
After attaching all necessary cables to your...

Tilt  
With the built - in pedestal, you can tilt the monitor for the most comfortable viewing angle.  
 
Removing the Stand  
After placing the monitor panel on a soft cloth or cushion, press and hold the LCD removal button, and then remove the stand.   
 
Back to Contents Page  NOTE: To prevent scratches on the LCD screen while removing the stand, ensure that the monitor is placed on a clean surface.