DELL 2150cdn User Manual

Understanding the Printer Menus289
Symbol Set
Purpose:
To specify a symbol set for a specified font.
Va l u e s :
Font Size
Purpose:
To specify the font size for scalable typographic fonts.
Va l u e s :
Font size refers to the height of the characters in the font. One point equals 
approximately 1/72 of an inch.
 NOTE: The Font Size menu is only displayed for typographic fonts.
See also:
Courier BdIt Helvetica BdOb ZapfDingbats
DESKTOP ISO L5 PC-8 TK
DNGBTSMS ISO L6 PI FONT
ISO-11 LEGAL PS MATH
ISO-15...

290Understanding the Printer Menus
Pitch and Point Size
Font Pitch
Purpose:
To specify the font pitch for scalable mono spaced fonts.
Va l u e s :
Font pitch refers to the number of fixed-space characters in a horizontal inch of 
type. For nonscalable mono spaced fonts, the pitch is displayed, but cannot be 
changed.
 NOTE: The Font Pitch menu is only displayed for fixed or mono spaced 
fonts.
See also:
Pitch and Point Size
Form Line
Purpose:
To set the number of lines in a page.
Va l u e s :
mm series...

Understanding the Printer Menus291
The printer sets the amount of space between each line (vertical line spacing) 
based on the Form Line and Orientation menu items. Select the correct 
Form Line and Orientation before changing Form Line.
See also:
Orientation
Quantity
Purpose:
To set the default print quantity. (Set the number of copies required for a specific 
job from the printer driver. Values selected from the printer driver always 
override values selected from the operator panel.)
Va l u e s :...

292Understanding the Printer Menus
Draft Mode
Purpose:
To save toner by printing in the draft mode. The print quality is reduced when 
printing in the draft mode.
Va l u e s :
LineTermination
Purpose:
To add the line termination commands.
Va l u e s :
Default Color
Purpose:
To specify the color mode to Color or Black. This setting is used for a print 
job that does not specify a print mode.
Va l u e s :
EnableEnables the Hex Dump feature.
Disable
*Does not print in the draft mode.
EnablePrints in the...

Understanding the Printer Menus293
Network
Use the Network menu to change the printer settings affecting jobs sent to the 
printer through the wired or wireless network.
 NOTE: Values marked by an asterisk (*) are the factory default menu settings.
Ethernet
Purpose:
To specify the communication speed and the duplex settings of Ethernet. The 
change becomes effective after the printer is turned off and then on again.
Va l u e s :
Wireless Status
 NOTE: Wireless Status feature is available only when the...

294Understanding the Printer Menus
Wireless Setup
 NOTE: Wireless Setup is available only when the printer is connected using the 
wireless network.
Purpose:
To configure the wireless network interface.
Va l u e s :
 

Understanding the Printer Menus295
Manual 
SetupEnter (SSID)Specifies a name to identify the wireless 
network. Up to 32 alphanumeric characters can 
be entered.
Infra-
structureSelect when you configure the wireless setting through the 
access point such as a wireless router.
No SecuritySpecifies No Security to configure the wireless 
setting without specifying a security method 
from WEP, WPA-PSK-TKIP, and WPA-PSK-
AES.
WEP(64Bit)Specifies the WEP 64 bit key to use through the 
wireless network. Up to...

296Understanding the Printer Menus
Reset Wireless
 NOTE: Reset Wireless feature is available only when the printer is connected 
using the wireless network.
Purpose:
To initialize wireless network settings. After executing this function and 
rebooting the printer, all wireless network settings are reset to their default 
values.
Va l u e s :
Ad-hocSelect to configure the wireless setting without the access point 
such as a wireless router.
No SecuritySelect to configure the wireless setting without...

Understanding the Printer Menus297
TCP/IP
Purpose:
To configure TCP/IP settings. 
Va l u e s :
IP Mode Dual Stack*Uses both IPv4 and IPv6 to set the IP 
address.
IPv4 ModeUses IPv4 to set the IP address.
IPv6 ModeUses IPv6 to set the IP address.
 

298Understanding the Printer Menus
Protocol
Purpose:
To enable or disable each protocol. The change becomes effective after the 
printer is turned off and then on again.
Va l u e s :
IPv4 Get IP Address AutoIP*Sets the IP address automatically. A random 
value in the range of 169.254.1.0 to 
169.254.254.255 that is not currently in use 
on the network is set as the IP address. The 
subnet mask is set as 255.255.0.0.
BOOTPSets the IP address using BOOTP.
RARPSets the IP address using RARP. 
DHCPSets the...