Dell 1909w Users Guide

Dell 1909W Flat Panel Monitor Users Guide
file:///T|/htdocs/monitors/1909W/en/ug/setup.htm[11/8/2012 2:53:45 PM]
Back to  Contents Page
Setting Up the Monitor
Dell™ 1909W  Flat Panel Monitor  Users Guide
  Attaching  the Stand
  Connecting  the Monitor
   Organizing Your  Cables
  Attaching  the Soundbar (optional)
   Removing the Stand 
Attaching the Stand
NOTE:  The  stand  is detached  when  the monitor is shipped from  the factory.
NOTE: This is applicable  for a  monitor with a  stand. When  the...

Dell 1909W Flat Panel Monitor Users Guide
file:///T|/htdocs/monitors/1909W/en/ug/setup.htm[11/8/2012 2:53:45 PM]
 WARNING: Before  you begin any of the procedures in this section, follow  the  Safety Instructions.
To connect your  monitor to  the computer: 1.  Turn off your  computer  and  disconnect the power cable.
2 .  Connect either  the white (digital  DVI-D) or the blue (analog VGA)  display  connector  cable  to  the corresponding  video  port on the back  of your  computer.  Do not use both...

Dell 1909W Flat Panel Monitor Users Guide
file:///T|/htdocs/monitors/1909W/en/ug/setup.htm[11/8/2012 2:53:45 PM]
 
NOTE: The  Graphics are used for the purpose  of illustration only. Appearance of the computer  may vary.
Connecting the USB cable
After you have  completed connecting  the DVI/VGA cable, follow  the procedure below  to  connect the USB  cable  to  the computer  and  complete  your  monitor setup:
1.  Connect the upstream  USB  cable  (cable supplied) to  the monitor upstream  port and  then...

Dell 1909W Flat Panel Monitor Users Guide
file:///T|/htdocs/monitors/1909W/en/ug/setup.htm[11/8/2012 2:53:45 PM]
After attaching  all necessary  cables to  your  monitor and  computer, (See Connecting  Your  Monitor for cable  attachment,) use the cable  management slot to organize all cables as shown
above.
Attaching the Dell Soundbar
CAUTION : Do not use with any device other than  Dell Soundbar.
 NOTE:  Soundbar Power Connector  +12V  DC output is for optional  Dell Soundbar only.
1. Working from  the...

Dell 1909W Flat Panel Monitor Users Guide
file:///T|/htdocs/monitors/1909W/en/ug/setup.htm[11/8/2012 2:53:45 PM]
NOTE: To prevent  scratches on the LCD  screen while  removing the stand,  ensure that  the monitor is placed on a  clean surface.
NOTE:  This is applicable  for a  monitor with a  stand. When  the OptiPlexTM USFF 780/  OptiPlexTM SFF 980 AIO stand  is bought, please refer to  the respective AIO stand  setup
guide for set  up  instructions.
To remove the stand:
1.  Rotate the stand  to  allow...

Dell 1909W Flat Panel Monitor Users Guide
file:///T|/htdocs/monitors/1909W/en/ug/operate.htm[11/8/2012 2:54:10 PM]
Back to  Contents Page
Operating the Monitor
Dell™ 1909W  Flat Panel Monitor  Users Guide
  Using the Front Panel Controls
   Using the On -Screen Display (OSD) Menu
  Setting  the Maximum Resolution
  Using the Dell Soundbar (Optional)
  Using the Tilt ,Rotation
  Rotating the monitor
  Adjusting the Rotation Display Settings of Your  System
Using the Front Panel
Use  the control buttons on...

Dell 1909W Flat Panel Monitor Users Guide
file:///T|/htdocs/monitors/1909W/en/ug/operate.htm[11/8/2012 2:54:10 PM]
Automatic Adjust /AdjustUp
Auto Adjustment allows  the monitor to  self-adjust  to  the incoming video  signal. After using  Auto Adjustment, you can  further tune
your  monitor by using  the Pixel  Clock  (Coarse)  and  Phase (Fine) controls under Image Settings.
NOTE : Auto Adjust  does  not occur if you press  the button while  there are no active video  input signals  or attached...

Dell 1909W Flat Panel Monitor Users Guide
file:///T|/htdocs/monitors/1909W/en/ug/operate.htm[11/8/2012 2:54:10 PM]
Using the On-Screen Display (OSD) Menu
 
Accessing the Menu System
NOTE: If  you change  the settings and  then  either  proceed to  another menu  or exit  the OSD menu,  the monitor automatically saves those  changes.  The  changes are also  saved  if you
change  the settings and  then  wait  for the OSD menu  to  disappear.
1.  Push the MENU button to  launch the OSD menu  and  display...

Dell 1909W Flat Panel Monitor Users Guide
file:///T|/htdocs/monitors/1909W/en/ug/operate.htm[11/8/2012 2:54:10 PM]
 
 NOTE: 
AUTO ADJUST  is only  available  when  you use the analog  (VGA) connector.
2.
 Push the  and   buttons to  move  between  the setting  options.  As you move  from  one  icon to  another,  the option name is highlighted.  See the following table for a  complete  list
of all the options available  for the monitor.
3.
 Push the MENU button once  to  activate the highlighted option....

Dell 1909W Flat Panel Monitor Users Guide
file:///T|/htdocs/monitors/1909W/en/ug/operate.htm[11/8/2012 2:54:10 PM]
 
 AUTO  ADJUST
Even though  your  computer  recognizes your  monitor on startup, the Auto Adjustment function optimizes the display  settings for use with your  particular
setup.
 
 
NOTE:  In most cases,  Auto Adjust  produces the best image for your  configuration.
 
NOTE:  AUTO ADJUST  option is only  available  when  you are using  the analog  (VGA) connector.
INPUT SOURCE Use  the...