Dell 1609WX Projector Users Guide
Have a look at the manual Dell 1609WX Projector Users Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 327 Dell manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Index51 Index A Adjusting the Projected Image 18 Adjusting the Projector Height 18 lower the projector Elevator button 18 Elevator foot 18 Tilt adjustment wheel 18 Adjusting the Projector Zoom and Focus 19 Focus ring 19 Zoom tab 19 C Changing the Lamp 41 Connecting the Projector Composite video cable 13 Connecting a Computer with a RS232 cable 10, 11 Connecting with a Component Cable 14, 15 Connecting with a Composite Cable 13 Connecting with an HDMI Cable 16 Connecting with an S-video Cable 12 DVI-D adapter 16 HDMI cable 16 Power cord 8, 9, 10, 11, 12, 13, 14, 15, 16 RS232 cable 10, 11 S-video cable 12 To Computer 8, 9 USB to USB cable 8, 9 VGA to VGA cable 8, 9 VGA to YPbPr cable 14 YPbPr to VGA cable 15 YPbPr to YPbPr cable 15 Connection Ports Audio input connector 7 Audio output connector 7 Composite video connector 7 DVI-D input connector 7 Power cord connector 7 RS232 connector 7 Security cable slot 7 S-video connector 7 USB remote connector 7 VGA-A input (D-sub) connector 7 VGA-A output (monitor loop-through) 7 VGA-B input (D-sub) connector 7 Contact Dell 5, 22, 39 Control Panel 21 D Dell
52Index contacting 47 M Main Unit 6 Control panel 6 Elevator button 6 Focus ring 6 IR receiver 6 Lens 6 Zoom tab 6 O On-Screen Display 25 Auto-Adjust 27 Display (in PC Mode) 30 Display (in Video Mode) 31 Input Select 26 Lamp 32 Language 33 Main Menu 26 Others 34 Picture (in PC Mode) 28 Picture (in Video Mode) 29 Set Up 27 P phone numbers 47 Powering On/Off the Projector Powering Off the Projector 17 Powering On the Projector 17 R Remote Control 24 IR receiver 22 S Specifications Audio 43 Brightness 43 Color Wheel Speed 43 Contrast Ratio 43 Dimensions 44 Displayable Color 43 Environmental 44 I/O Connectors 44 Lamp 43 Light Valve 43 Noise Level 43 Number of Pixels 43 Power Consumption 43 Power Supply 43 Projection Distance 43 Projection Lens 43 Projection Screen Size 43 Regulatory 44 RS232 Protocol 45 Uniformity 43 Video Compatibility 43 Weight 44 support contacting Dell 47 T telephone numbers 47
Galaxy 3 Series Programming Manual 48 4 = Conn. Retry If the attempt to initiate a remote servicing call fails, the panel can be programmed do repeat dial attempts. There are three further options: 1 = Retry Interval The dial attempts can be programmed to occur from 0-60 minutes. Setting the value to 0 disables the feature The default setting is 30 minutes. 2 = Retry Duration The length of time that the panel tries to do a remote servicing call can be programmed from 0-24 hours. setting the value to 0 disables the feature. The default setting is 6 hours. 3 = Redial Mode In the event of a remote servicing session terminating unexpectedly, the panel enters one of the three program- mable modes that follow. 0 = Off The panel does not try to re-establish a connection. 1 = Retry The panel initiates a remote servicing call to re-establish a connection. The retries will be as per option 47.4.4.1 (Retry Interval) and 47.4.4.2 (Retry Duration). 2 = Direct The panel access mode changes to allow direct access for 30 minutes. This mode operates as per option 47.1=Service when Direct Access is selected. 5 = Control Upload This option controls whether a connection is established when only engineer or user programming data is uploaded. This feature has three options. 1 = Eng Prog Only initiates a connection when engineering programming has been modified. 2 = User Prog Only initiates a connection when user programming has been modified. 3 = Either Initiates a connection when either engineering or user programming has been modified. 6 = Remote Maint This option controls the mode for automatically initiating communications for remote routine inspection and maintenance. The panel uploads only the most recent information available from 61=Diagnostics. No other panel programming is uploaded. There are two sub-options that control this: 47 - Remote Access (contd)
Galaxy 3 Series Programming Manual 49 47 - Remote Access (contd) 1 = Schedule This option controls the schedule for the initiation of communication for remote routine inspection. The sched- ule can be set from 0-365 days. The default is 0 days which disables the function. 2 = Advice This option controls the method by which communication is initiated. It can be initiated automatically by the schedule programmed above or manually by user entry of the Service PIN code, with or without a notification message. There are three options. The default value for each is disabled. 1 = Code Only Entry of a Service PIN code automatically initiates a remote servicing connection to call back number 1. The Service PIN code can only be modified by remote users. When the Service PIN code is entered, it resets any scheduled connection timers. 2 = Code + Notice This enables the remote servicing notification timer, and display of remote servicing notification. The remote service notification message is not displayed if the system is set. It only becomes active when the panel is unset. The message REMOTE CALL INIT, A=SP PIN ENTER is displayed on the keypad after entry of a valid manager type user code. 3 = No Code/Notice This enables a remote servicing session without the need for a Service PIN code and the panel’s remote servicing notification message. This option uses the start and end times programmed in menu 47.4.2.1 and 47.4.2.2 respectively. 7 = Service Pin This is a 6-digit numeric Service PIN code (default 987654), which initiates an automated call to the Remote Servicing application. The Service PIN code can only be changed from Galaxy Gold and sending the Service PIN code to the panel via the Send Remote Access Start Code. The Service PIN code cannot be the same as any other user codes on the system. This option is only available when option 47.4.6.1 (schedule) is greater than 0 and when option 47.4.6.2.1 (code only) are enabled. 8 = Send Panel ID When a remote servicing connection is established, this option allows panel identification and authentication. When enabled, the following sequence of events occur. Once a remote servicing connection is established, whether panel or PC initiated, the panel delays for a period as determined by Delay Time for incoming information from the remote servicing package. If a valid control character is received by the panel within the delay period, the panel transmits an identity string. If no character is received during the delay period the call is terminated. 9 = Delay Time This is the time that the panel delays for incoming information from the remote servicing package. The delay time can be set from 3-10 seconds. The default is 3 seconds
Galaxy 3 Series Programming Manual 50 Option 48 – Access Authorization This option allows access to be authorized for engineers for system programming and for managers in order to add/delete/change all user codes. 1 = Engineer The engineer code is assigned programmed as dual by default. This prevents the engineer from accessing engineer mode unless authorized to do so by a valid code. To gain access to the engineer menu a type 3.6 user must enter their code, and enable the Engineer Access option. This provides a five minute period during which a single entry of the engineer code provides access to engineering mode without causing a tamper alarm. Once the engineer mode has been accessed, there is no time limit on the access period. If the Engineer Mode option has not been enabled, or the code is not entered within the five minute period, then the Engineer code is invalid and has no effect. If the PIN is programmed without the #, the Engineer Access option does not require to be enabled to allow the engineer to gain access to engineer mode. The engineer code requires to be entered twice. The first entry activates a tamper alarm which is cancelled by the second entry. NOTE:Dual entry of the engineer code in a system requiring user authorization does not give access to engineer mode. 2 = Manager This option allows type 3.6 manager codes to be enabled for user code adding/deleting/changing. This option can only be enabled by the authorization code. However, this option is not used by default. Manager codes are always authorized. It can be enabled, if required, to comply with standards in certain regions. An authori- zation code must be assigned in Menu 42 Codes, before the function is enabled. 48 - Engineer Access
Galaxy 3 Series Programming Manual 51 Section 8: Engineer 1 Option 51 – Parameters This option allows the engineer to modify the system functions. Options can be selected using the A or B keys or by entering the two digit parameter number and pressing the ent key. The selected options can then be programmed by using the A key to increase or the B key to decrease the values assigned to the parameter; pressing the ent key accepts the new value and returns to the previous menu level. Any parameters that differ from this procedure are indicated in the following paragraphs. The parameters also prompt the engineer on which keys to press. For example, press: •1 then 6parameter 16 = Soak Time selected; •entcurrently soak time is displayed along with the programmable range 07 (1–14) days; • 08value of the required soak time, the display shows the new value 08 (1–14) days; •entaccept the programming and return to 16 = Soak Time displayed. NOTE:Default settings must be changed before programming in Menu Option 55 – Soak. Assigning Parameters to Groups Several of the parameters allow separate values to be assigned to the groups on the system. If groups have been enabled, the relevant parameters prompt for a group to be selected; when selected, the value is assigned to the group parameter using the procedure outlined in the previous example. The parameters that permit group selection are indicated in the following paragraphs. 51 - Parameters
Galaxy 3 Series Programming Manual 52 51 - Parameters (cont’d) Table 9. System Parameters Parameter Groups Galaxy 48 Galaxy 144 Galaxy 520 53RF Stop Mode not available99 9 54Keypad Access not available99 9 55Confirm not available99 9 56Force Restore not available99 9 57Bell Extend not available99 9 58Power Alarm not available99 9 59Part Tone not available99 9 60RF Parameters not available99 9 61Activity Mon not available99 9 62Lockout not available99 9 63Banner alerts not available99 9 64Set Override not available99 9 65Reset Levels not available99 9 66Min Pin Size not available99 9 67Level Format not available99 9 68Line Fail not available99 9 69Alert Inds not available99 9 70SWDC Set Dly not available99 9 71MF BL Enable not available99 9 72Max Alm Cause not available99 9Parameter Groups Galaxy 48 Galaxy 144 Galaxy 520 01B ell Ti me99 9 9 02B ell D elay99 9 9 03Abort Time99 9 9 04Exit Time99 9 9 05Entry Time99 9 9 06System Reset99 9 9 07Tamper Reset99 9 9 08No. Re-arms99 9 9 09Omi t All99 9 9 10Key 0 not available99 9 11Local Part99 9 9 12Banner not available99 9 13PA D elay99 9 9 14KEY/SW Level not available99 9 15System Text not available99 9 16Soak Time not available99 9 17Restart not available99 9 18Stop Set not available99 9 19Part Alarm99 9 9 20Power Delay99 9 9 21Reset Mgr. not available99 9 22PA reset99 9 9 23Print Codes not available99 9 24Exit Alarm99 9 9 25Global Copy not available99 9 26Forced not available99 9 27cct Debounce not available99 9 28Online print not available99 9 29Online level not available99 9 30Video99 9 9 31Delay Alarm99 9 9 32Show Alarms not available99 9 33Secure Code not available99 9 34 Comfort Time not available99 9 35Fail To Set99 9 9 36Battery Size not available99 9 37Standby Time not available99 9 38ATM Delay not available99 9 39ATM Timeout not available99 9 40Datelock not available not available not available not available 41Weekend Work not available99 9 42PIN Change not available99 9 43Timer Access not available not available not available not available 44Early Open not available99 9 45High Security not available99 9 46Res. Select not available99 9 47Set Confirm not available99 9 48Alarm Limits not available99 9 49Confirm Time not available99 9 50RF Bat Delay not available99 9 51RF Jam Delay not available99 9 52RF Stop Set not available99 9
Galaxy 3 Series Programming Manual 53 01 = Bell Time The duration of the Bells output activation is programmable within the range 0–30 minutes; the default is 15. Assigning a value of 00 minutes sets the Bell Time to infinity. This parameter can be assigned a different value for each group. The Entry/Exit Horn is subject to the Bell Time parameter in both the set and unset conditions. 02 = Bell Delay The delayed activation of the bell is programmable within the range 0–20 minutes; the default is 0. The Bell Delay is overridden by a comms failure (either a Comms Fail on the Communication Module or by the activation of a Line Fail zone used to monitor a digicom); an alarm condition in either of these conditions results in instant bells activation. This parameter can be assigned a different value for each group. 03 = Abort Time The abort function delays the activation of a full intruder alarm condition following an entry alarm. This param- eter has 2 sub-options: 1 = Abort Time The abort time is programmable within the range 0-300 seconds and can be assigned a different value for each group. The abort time will be initiated: • whenever a zone that is not on the entry route (Final, Entry and Exit zones) is activated — a user strays from the entry route; • a valid code is not entered before the entry time expires. The abort operation can be modified by adding a º or # to the programmed time. The standard abort operation is as follows: ƒFor entry route deviation, the signalling of an intruder alarm is delayed. ƒIf a valid code is entered before the entry time expires: (1) The intruder is not signalled. (2) The system does not require a system reset. ƒIf a valid code is not entered before the entry time expires or an entry timeout condition occurs: (1) The intruder is signalled at the end of the entry time. (2) The Abort timer starts on expiry of the entry time. ƒIf a valid code is entered within the programmed abort time: (1) If an abort output/channel is allocated to the alarmed group: a) The Abort signal is sent. b) The intruder condition is not restored. c) Intruder restore is not signalled. (2) If there is no abort output allocated to the alarmed group: a) The intruder condition is restored. b) Intruder restore is signalled ƒIf the programmed abort time is allowed to expire without a valid code being entered, then the system requires a system reset. The panel cannot be set until this occurs. NOTE:If reduced resets (51.55.3) is enabled, the alarm will be reset by the user code, if the alarm is unconfirmed. 51 - Parameters (cont’d)
Galaxy 3 Series Programming Manual 54 Modified Abort Operation Hash # abort alters the standard operation so that the signalling of the intruder condition is delayed until the end of the abort time. If the system is unset during the entry time or abort time, no alarm conditions will be signalled. Star º abort alters the standard operation so that if a user strays from the entry route within the entry time, the intruder is signalled as soon as the entry deviation occurs. NOTE 1:To comply with DD243:2002, the Standard abort operation must be used, with the abort time set to 001 seconds. NOTE 2:To comply with EN50131:2004 and DD243:2004, the Hash # abort operation must be used with the Abort Time set to 30 seconds or longer. 2=Bell Delay This option is either enabled or disabled. When enabled, it will hold off the start of any bell delay time pro- grammed in parameter 03, until the end of the abort time programmed above. 04 = Exit Time This parameter determines the time allowed to leave the premises via the exit route before the system sets. The Exit Time is programmable within the range 0–300 seconds; the default is 120 seconds. Infinite Exit Time Assigning a value of 000 seconds sets the Exit Time to infinity; an Exit terminator activation (Final or Push- set zone) is required to complete the setting of the system. The infinite Exit Time is normally used with a Push-set zone to terminate the setting and an Entry zone to start the unsetting procedure. NOTE:If the system is programmed to Autoset and the Exit Time is programmed to 000, the Exit Time will be set to 60 seconds for the Autoset — there is no requirement for a Push-Set zone to be activated. Setting Multiple Groups This parameter can be assigned a different value for each group. If more than one is group is being set, the longest exit time is adopted for all setting groups. 51 - Parameters (cont’d)