DELL 1133n User Manual

							Supplies
This chapter provides  information  on purchasing supplies,  accessories and  maintenance parts available  for your
machine.
This chapter includes:
How  to  purchase
Available  supplies
Replacing  the toner cartridge
Available  accessories may differ from  country to  country.  Contact  your  sales  representatives to  obtain the list of
available  accessories.
How to purchase
To order  Dell-authorized supplies and  accessories visit www.dell.com/supplies ,  or contact  your  local  Dell dealer or
the retailer  where you purchased  your  machine.  You  can  also  visit 
www.dell.com  or support.dell.com ,  select your
country/region, and  obtain information  on calling for service.
Available supplies
When  supplies reach  their lifespan, you can  order  the following types of supplies for your  machine:
Type Average yield
[a]Part  number
Standard  capacity toner cartridge Approx.  1,500 pages3J11D
High  capacity toner cartridge Approx.  2,500 pages2MMJP
[a] Declared yield  value  in accordance with ISO/IEC 19752.
To

 replace a  toner cartridge see 
Replacing  the toner cartridge .
Depending on the options and  job mode used, the toner cartridge’s  lifespan may differ.
You  must  purchase supplies,  including toner cartridges, in the same  country where you purchased  your  machine.
Otherwise, it  will be incompatible with your  machine since the system  configuration of these vary from  country to
country.
Dell does  not recommend  using  non-genuine Dell  toner cartridge such as refilled or remanufactured  toners.  Dell
cannot guarantee  non-genuine  Dell toner cartridges  quality.  Service  or repair  required  as a  result  of using  non-
genuine  Dell toner cartridges  will not be covered under the machine warranty.
Replacing the toner cartridge
Click  this link  to  open an animation about  replacing a  toner cartridge.
When  a  toner cartridge has  reached its  estimated cartridge life:
End  of  life  Replace new  cart  message  appears on the display.
At this stage,  the toner cartridge needs to  be replaced. Check the type of the toner cartridge for your  machine (See
Available  supplies ).
1 .  Open the front door.
2 .  Pull the toner cartridge out.
 
						

							3.  Take a  new toner cartridge out of its  package.
4 .  Remove the paper protecting  the toner cartridge by pulling  the packing tape.
5.  Locate  the sealing  tape at the end  of the toner cartridge.  Carefully  pull the tape completely out of the cartridge
and  discard  it.
The  sealing  tape should be longer than  60  cm (23.6 inches) when  correctly  removed.
Holding the toner cartridge,  pull the sealing  tape straight to  remove it  from  the cartridge.  Be  careful
not to  cut the tape. If  this happens,  you cannot use the toner cartridge.
Refer to  the pictures on the cartridge wrapping paper.
6 .  Slowly shake  the cartridge five or six times  to  distribute  the toner evenly inside  the cartridge.  It will assure
maximum  copies per cartridge.
If  toner gets on your  clothing, wipe it  off with a  dry cloth  and  wash clothing in cold  water. Hot  water  sets
toner into fabric.
Do not touch the green underside  of the toner cartridge.  Use  the handle  on the cartridge to  avoid  touching
this area.
7 .  Hold  the toner cartridge by the handle  and  slowly  insert  the cartridge into the opening in the machine.
Tabs  on the sides of the cartridge and  corresponding  grooves within  the machine will guide the cartridge into the
correct position  until it  locks  into place  completely.
 
						

							8.  Close  the front door. Make sure  that  the cover is securely closed.
 
						

							Specifications
This chapter includes:
Hardware  specifications
Environmental  specifications
Electrical  specifications
Print media specifications
The  specification  values are listed  below,  specification  are subject to  change  without  notice. See www.dell.com or
support.dell.com  for possible changes in information.
Hardware specifications
Item Description
Dimensions Height 275.8 mm  (10.9 inches)
Depth 409 mm  (16.1 inches)
Width 416 mm  (16.4 inches)
Weight Machine  with consumables 10.59 Kg (23.35  lbs)
Package weight Paper 2.13  Kg (4.7  lbs)
Plastic 0.62  Kg (1.37 lbs)
Environmental specifications
Item Description
Noise Level
[a ]Ready  mode 26  dB(A)
Printing  mode 50  dB(A)
Temperature Operation 10  to  32  °C (50 to  90  °F)
Storage  (unpacked) 0 to  40  °C (32 to  104 °F)
Humidity Operation 20  to  80%  RH
Storage  (unpacked) 10  to  80%  RH
[a] Sound  Pressure Level, ISO 7779. Configuration  tested: machine basic installation,  A4 paper, simplex  printing.
Electrical specifications
Power requirements  are based on the country/region  where the device is sold. Do not convert  operating  voltages.
Doing so might damage  the device and  void  the product warranty.
Item Description
Power rating
[a ]
110 volt models AC 110 - 127 V
220 volt models AC 220 - 240 V
Power consumption Average operating  mode Less  than  370 W
Ready  mode Less  than  45  W
Power save mode Less  than  10  W
Power off mode Less  than  1 W
[a] See the rating label on the machine for the correct voltage, frequency (hertz) and  type of current for your
machine.
Print media specifications
Print media weight[a ]/Capacity[b]
 
						

							TypeSize Dimensions
Tray1 Manual  tray
Plain paper Letter
216

 x  279
 mm
(8.50

 x  11.00
inches)
60

 to  120
 g/m2
(16 to  32 lb bond)
250 sheets  of
80g/m
2 (20 lb
bond)
60
  to  163
 g/m2 (16
to

 43
 lb

 bond)
1 sheet
stacking
Legal216
 x  356 mm
(8.50

 x  14.00
inches)
US Folio
216

 x  330
 mm
(8.50

 x  13.00
inches)
A4
210

 x  297
 mm
(8.27

 x  11.69
inches)
Oficio
216

 x  343
 mm
(8.50

 x  13.50
inches)
JIS B5
182

 x  257
 mm
(7.17

 x  10.12
inches)
60

 to  90
 g/m2 (16
to

 24
 lb

 bond)
150 sheets  of
80  g/m
2 (20
lb bond)
ISO B5176
 x  250 mm
(6.93
 x  9.84
inches)
Executive
184

 x  267
 mm
(7.25

 x  10.50
inches)
A5
148

 x  210
 mm
(5.83

 x  8.27
inches)
A6
105

 x  148
 mm
(4.13

 x  5.83
inches)
Envelope Envelope Monarch
98

 x  191
 mm
(3.87

 x  7.50
inches) Not available  in
tray1
75

 to  90
 g/m2 (20
to

 24
 lb

 bond)
1 sheet
stacking
Envelope No. 10105
 x  241 mm
(4.12

 x  9.50
inches)
Envelope DL
110

 x  220
 mm
(4.33

 x  8.66
inches)
Envelope C5
162

 x  229
 mm
(6.38

 x  9.02
inches)
Envelope C6
114

 x  162
 mm
(4.49

 x  6.38
inches)
Thick paper Refer to  the Plain paper section Refer to  the Plain
paper section90  g/m
2 (24 lb
bond) 90  g/m2 (24 lb
bond)
1 sheet
stacking
Thin paper Refer to  the Plain paper section Refer to  the Plain
paper section60  to  70  g/m
2 (16
to  19  lb bond) 60  to  70  g/m2 (16
to  19  lb bond)
1 sheet
stacking
Transparency Refer to  the Plain paper section Refer to  the Plain
paper sectionNot available  in
tray1
138 to  146 g/m
2
(36.81  to  38.91 lb
bond)
1 sheet
stacking
 
						

							Labels[c]Letter, Legal,  US Folio, A4,  JIS B5,  ISO
B5,  Executive,  A5,  Statement Refer to  the Plain
paper sectionNot available  in
tray1
120 to  150 g/m2
(32 to  40  lb bond)
1 sheet
stacking
Card  stock Letter, Legal,  US Folio, A4,  JIS B5,  ISO
B5,  Executive,  A5,  Statement, PostCard
4x6 Refer to  the Plain
paper section
Not available  in
tray1
105 to  163 g/m
2
(28 to  43  lb bond)
1 sheet
stacking
Minimum  size (custom)
76

 x  127
 mm
(3.00

 x  5.00
inches) Not available  in
tray1
60

 to  163
 g/m2 (16
to

 43
 lb

 bond)
Maximum

 size (custom)
216

 x  356
 mm
(8.50

 x  14.02
inches)
[a ] If  media weight  is over 120 g/m2 (32 lb), load  a  paper into the tray  one  by one.
[b] Maximum capacity may differ depending on media weight, thickness, and  environmental conditions.
[c] Smoothness: 100 to  250 (sheffield).
 
						

							Getting started
This chapter gives  you step-by-step instructions for setting  up  the USB  connected machine and  software.
This chapter includes:
Setting  up  the hardware
Supplied software
System  requirements
Installing USB  connected machine’s  driver
Sharing your  machine locally
Setting up the hardware
This section shows  the steps to  set  up  the hardware,  as explained in the Quick Install Guide.  Make sure  you read the
Quick Install Guide  first and  follow  the steps below:
1 .  Select a  stable  location.
Select a  level,  stable  place  with adequate space  for air circulation.  Allow extra  space  to  open covers  and  trays.
The  area should be well ventilated and  away  from  direct  sunlight or sources of heat,  cold, and  humidity.  Do not
set  the machine close  to  the edge  of your  desk or table.
Printing  is suitable for altitudes under 1,000 m (3,281  ft.).  Refer to  the altitude setting  to  optimize  your  printing
(See 
Altitude adjustment ).
Place  the machine on a  flat, stable  surface so that  there is no incline greater than  2 mm  (0.08 inch). Otherwise,
printing quality may be affected.
2 .  Unpack the machine and  check  all the enclosed items.
3 .  Remove all tape.
4 .  Install the toner cartridge.
5 .  Load paper (See 
Loading  paper in the tray ).
6 .  Make sure  that  all cables are connected to  the machine.
7 .  Turn the machine on.
 
						

							This equipment  will be inoperable  when  mains  power fails.
Supplied software
After you have  set  up  your  machine and  connected it  to  your  computer, you must  install the printer software using
the supplied  CD. The  software CD provides  you with the following software.OS Contents
Windows
Printer driver: Use  this driver  to  take  full advantage  of your  machine’s  features.
Scanner driver: TWAIN  and  Windows Image Acquisition  (WIA)  drivers are available  for scanning
documents on your  machine.
Printer Settings Utility: This  program  allows  you to  set  up  printer’s other options from  your
computer  desktop.
Printer Status  Monitor: This  program  allows  you to  monitor the machine’s  status and  alerts you
when  an error occurs during printing.
SmarThru[a ]: This program  is the accompanying Windows-based software for your  multifunctional
machine.
Dell  Scan  and Fax Manager: You  can  find out about  Scan  Manager program  information  and
installed  scan  drivers condition.
Dell  1133  Laser MFP Toner Reorder: The  Dell 1133 Laser MFP  Toner Reorder  window  also
displays  the level of toner remaining and  allows  you to  order  replacement toner cartridge.
Firmware  Update Utility: This  program  helps you to  update printer’s firmware.
Macintosh
Printer driver: Use  this driver  to  take  full advantage  of your  machine’s  features.
Scanner driver: TWAIN  driver  is available  for scanning  documents on your  machine.
Linux
Unified Linux Driver: Use  this driver  to  take  full advantage  of your  machine’s  features.
SANE: Use this driver  to  scan  documents.
[a] Allows  you to  edit a  scanned image in various ways  using  a  powerful image editor  and  to  send the image by
email. You  can  also  open another image editor  program, such as  Adobe Photoshop,  from  SmarThru .  For  details, refer
to  the on screen help supplied  on the  SmarThru program  (See 
Smarthru).
System requirements
Before  you begin,  ensure that  your  system  meets the following requirements:
Microsoft® Windows®
Your  machine supports  the following Windows operating  systems.
OPERATING SYSTEM Requirement  (recommended)
CPU
RAMfree HDD
space
Windows® 2000 Intel® Pentium®  II  400 MHz (Pentium III  933 MHz) 64  MB  (128
MB)600 MB
Windows® XP Intel® Pentium®  III  933 MHz (Pentium IV  1 GHz) 128 MB  (256
MB)1.5 GB
Windows Server®
2003 Intel® Pentium®  III  933 MHz (Pentium IV  1 GHz)
128 MB  (512
MB)1.25  GB to  2
GB
Windows Server®
2008 Intel® Pentium®  IV  1 GHz (Pentium IV  2 GHz)
512 MB  (2048
MB)10  GB
Windows Vista® Intel® Pentium®  IV  3 GHz 512 MB  (1024
MB)15  GB
Windows® 7 Intel® Pentium®  IV  1 GHz 32 -bit or 64 -bit processor  or
higher 1 GB (2  GB)
16  GB
Support for DirectX®  9 graphics with 128 MB  memory (to enable the Aero theme).
DVD-R/W Drive
Windows Server®
2008 R2 Intel® Pentium®  IV  1 GHz (x86)  or 1.4 GHz (x64)  processors
(2  GHz or faster) 512 MB  (2048
MB)10  GB