DELL 1133n User Manual

Do not push the paper width guide too  far causing the media to  warp.
If  you do not adjust  the paper width guide,  it  may cause paper jams.
Do not use paper with more  than  6 mm curl.
Loading paper in the tray
Tray  1
1.  Pull out the paper tray. And  adjust  the tray  size to  the media size you are loading (See Changing the tray
size ).
2 .  Flex or fan  the edge  of the paper stack to  separate  the pages before loading paper.
3.  And  place  paper with the side  you want  to  print  facing...

is useful  for single  page  printing on letterhead or colored paper.
Tips on using the manual  tray
If  you select Manual Feeder for Source  from  your  software application, you need  to  press   OK each  time
you print  a  page  and  load  only  one  type, size and  weight  of print  media at a  time in the manual tray.
To prevent  paper jams, do not add  paper while  printing when  there is still paper in the manual tray. This
also  applies  to  other types of print  media.
Print media should be...

CardStock●
Labels ●
Transparency ●
Envelope ●
Preprinted ●
Cotton ●
Recycled ●●
Archive ●●
( ● : supported, Blank: not supported)
The  media types are shown in the Printing Preferences .  This paper type option allows  you to  set  the type of paper
to  be loaded in the tray. This setting  appears in the list, so that  you can  select it.  This will let  you get  the best quality
printout.  If  not, the desired print  quality may not be achieved.
Plain: Normal  plain paper. Select this type if your...

When  selecting  envelopes, consider the following factors:
Weight: The weight  of the envelope  paper should not exceed  90 g/m2 otherwise, jam  may occur.
Construction: Prior  to  printing, envelopes should lie flat with less than  6 mm  curl, and  should not contain
air.
Condition: Envelopes should not be wrinkled,  nicked,  nor damaged.
Temperature: Use envelopes that  are compatible with the heat and  pressure  of the machine during
operation.
Use  only  well-constructed envelopes with sharp-and...

Do not use transparencies that  separates from  the backing sheet.
To prevent  transparencies from  sticking to  each  other,  do not let  the printed sheets  stack up  as they are being
printed out.
Labels
To avoid  damaging the machine,  use only  labels designed for use in laser  machines.
When  selecting  labels,  consider the following factors:
Adhesives: The adhesive  material should be stable  at your  machine’s  fusing temperature  of about  170
°C (338  °F).
Arrangement: Only  use labels with no...

Letterhead/ Preprinted  paper must  be printed with heat-resistant  ink that  will not melt,  vaporize,  or release
hazardous  emissions  when  subjected  to  the machine’s  fusing temperature  for 0.1 second.  Check your
machine’s  specification  to  view  the fusing temperature  of about  170 °C (338  °F).
Letterhead/ Preprinted  paper ink must  be non-flammable  and  should not adversely affect machine rollers.
Forms  and  letterhead should be sealed in a  moisture -proof  wrapping to  prevent...

3.  Press  the left/right  arrow until Paper  Setup  appears and  press  OK.
4 .  Press  the left/right  arrow until Paper  Source  appears and  press  OK.
5 .  Press  the left/right  arrow to  select the paper tray  you want.
6 .  Press   OK to  save the selection.
7 .  Press   Stop/Clear  (
) to  return  to  ready  mode.
Using the output support
The  surface of the output tray  may become hot if you print  a  large  number of pages at once. Make sure  that  you
do not touch the surface,  and  do not...