Daewoo Fr 330 Service Manual

Serv ic e M an ual
R efr ig era to r
M odel:  F R -330
DA EW OO E LEC TR O NIC S C O ., L T D .
S/M  N o. :  F R33000011
 

co nte n ts
1 . S PEC IF IC AT IO N ......................................................................................1
2 . N AM E O F P A R TS  .....................................................................................2
3 . R EFR IG ER AN T C YC LE  D IA G RAM  .........................................................3
4 . M AC HIN E R O OM  V IE W  A N D P A R T L IS T ................................................4
5 . M ETH O DS O F E XC HAN G IN G  M AIN  P A R TS...

1.Specification
Refrigerant
R134a
COOLING System
Refrigeration System
Defrost System
Defrost Operation
Cold Control
Freezer
Refrigerator
Total
Height
Width
Depth
Net Weight
-1-207L
268L 100g
Fan Cooling Convection Type
Air Forced Convection
Forced Fin-Evaporator Type
57Kg External
Dimension1636mm
600mm
729mm Automatic Start & Stop
Adjustable Dial
Capacity  61L
 

2. NAME OF PARTS
-2-
 

3. REFRIGERANT CYCLE DIAGRAM
-3-
 

NO PART NAME NO PART NAME NO PART NAME
1 BASE CAB AS7 WI-CON PIPE 13BASE COMP AS
2 COMPRESSOR 8 DRYER AS 14 BRACKET EARTH
3 P-RELAY AS 9 PIPE SUC AS 15 POWER CORD AS
4 PIPE VAPORI AS 10 PIPE SUC CONN 16 ABSORBER PIPE A
5 ABSORBER PIPE B 11 BOX POWER AS
6 PIPE HOT 12 HARNESS EARTH
4. MACHINE ROOM VIEW AND PART LIST
-4-
 

(1) Freezing room louver
1) Unscrew, remove the F-louver by 
   pulling forward with inserting 
   screwdriver into the hole of F louver.
2) Assemble it by pressing triangle
   shape (        ) by hand.
(2) R control box
1) After pressing both bottom surfaces
   of shade and pull forward.
2) To exchange the interior lamp,
   unscrew the lamp counterclockwise.
3) Remove two screws 
5. METHODS OF EXCHANGING MAIN PARTS
-5-
 

Methode of exchanging main parts
4) Pull slightly forward with instant force.
5) Remove the housing
6) After romoving the control switch knob  
   and two screws for fixing control switch,
   change the control switch to new one.
-6-
 

Methode of exchanging main parts
(3) Bimetal
1) Cut off the wire bind.
2) Take out the bimetal.
(4) Glass tube heater
1) Remove 2 screws that fasten the evaporator.
2) Slightly pull the evaporator to the arrows
    direction.
3) Move the entire eveporator upward the pipe
    center to the arrows direction.
    (Do not crumble the part A of the 
     accumulator during the process.)
-7-
Evaporator fastening screw
BIMETAL
 

Methode of exchanging main parts
4) Cut the both ends of glass tube heater tube
    heater lead wires and insulate and seal lead
    tip remaining in refrigerator with tape etc.
5) Pull out the glass tube heater from the heater
    supporter with heater covers remaining.
    (upper and lower) (Do not apply much 
    power on the heater supporter.)
6) Install the heater covers (upper and lower) 
    on a new glass tube heater. (Make the cover
    with holes the lower one)
7) Place the glass tube heater...