D-Link Router AirPlus DI-614+ User Manual

51
Troubleshooting
2. The wireless client cannot access the Internet in the Infrastructure mode.
Make  sure  the  wireless  client  is  associated  and  joined  with  the 
correct router. To check this connection: Right-click on the Local Area 
Connection icon in the taskbar> select View Available Wireless Networks. 
The Connect  to  Wireless  Network  screen  will  appear.    Please  make 
sure  you  have  selected  the  correct  available  network,  as  shown  in 
the illustrations below.
Check that...

52
Troubleshooting
3.  Check that the drivers for the network adapters are installed properly.
You  may  be  using  different  network  adapters  than  those  illustrated  here,  but  this 
procedure  will  remain  the  same,  regardless  of  the  type  of  network  adapters  you  are 
using.
Go to Start.
Right-click on My 
Computer. 
Click Properties.
 
 
 
NOTE:  Screen  shots  taken  using 
Windows  XP.  If  you  are  using  a 
different  Operating  System  your 
screen may look different.
Select...

53
Troubleshooting
Double-click on Network 
Adapters.
Right-click on D-Link AirPlus 
DWL-650+ Wireless Cardbus 
Adapter.
Select Properties to check 
that the drivers are installed 
properly.
D-Link AirPlus DWL-650+ Wireless Cardbus 
Look under Device Status to 
check that the device is working 
properly. 
Click OK.
 
 
 
 
  

54
4.  Resetting the DI-614+ to Factory Default Settings
After you have tried other methods for troubleshooting your network, you 
may choose to Reset the DI-614+ to the factory default settings.  Remember 
that D-Link AirPlus products network together, out of the box, at the factory 
default settings.  
Troubleshooting
To hard-reset the D-Link AirPlus DI-614+ to Factory Default Settings, please do the 
following:
Locate the Reset button on the back of the DI-614+.
Use a paper clip to press the Reset...

55
Using the Network Setup Wizard in Windows XP
In this section you will learn how to establish a network at home or work, 
using Microsoft Windows XP.  
Note:  Please refer to websites such as http://www.homenethelp.com
and http://www.microsoft.com/windows2000  for information about networking 
computers using Windows 2000, Me or 98.
Go to Start>Control Panel>Network Connections
Select Set up a home or small office network
Networking Basics
When this screen appears, Click Next. 

56
 
Please follow all the instructions in this window:
Networking Basics
Click Next.
In  the  following  window,  select  the  description  that  best  fits  your  computer.  If 
your  computer  connects  to  the  internet  through  a  gateway/router,  select  the 
second option as shown.
Click Next. 

57
Enter a Computer description and a Computer name (optional).
Networking Basics
Click Next.
Enter a Workgroup name. All computers on your network should have the same 
Workgroup name.
Click Next. 

58
Please wait while the Network Setup Wizard applies the changes.
Networking Basics
When the changes are complete, click Next.
Please wait while the Network Setup Wizard configures the computer.  
This may take a few minutes. 

59
Networking Basics 
In the window below, select the option that fits your needs. In this example, Create a 
Network Setup Disk has been selected.  You will run this disk on each of the computers 
on your network. Click Next.
Insert a disk into the Floppy Disk Drive, in this case drive A. 

60
Networking Basics 
Please read the information under Here’s how in the screen below. After you complete 
the Network  Setup  Wizard  you  will  use  the Network  Setup  Disk to  run  the Network  Setup 
Wizard once on each of the computers on your network. To continue click Next.