D-Link Dir655 B1 Manual

							87D-Link DIR-655 User Manual
Section 3 - Configuration
Stats
The screen below displays the Traffic Statistics. Here you can view the amount of packets that pass through the DIR-655 on both the Internet and the LAN 
ports. The traffic counter will reset if the device is rebooted.
Active Sessions  
						

							88D-Link DIR-655 User Manual
Section 3 - Configuration
Routing
The wireless client table displays a list of current connected wireless clients. This table also displays the connection time and MAC address of the 
connected wireless clients.
Wireless  
						

							89D-Link DIR-655 User Manual
Section 3 - Configuration
IPV6
IPV6 Routing  
						

							90D-Link DIR-655 User Manual
Section 3 - Configuration
Support  
						

							91D-Link DIR-655 User Manual
Section 4 - Connecting to a Wireless Network
WPS Button
Step 2 - Within 2 minutes, press the WPS button on your wireless client (or launch the software utility and start the WPS process).
The easiest and most secure way to connect your wireless devices to the router is WPS (Wi-Fi Protected Setup). Most wireless devices such as wireless 
adapters, media players, Blu-ray DVD players, wireless printers and cameras will have a WPS button (or a software utility with WPS) that you can 
press to connect to the DIR-655 router. Please refer to your user manual for the wireless device you want to connect to make sure you understand 
how to enable WPS. Once you know, follow the steps below:
Step 1 - Press the WPS button on the DIR-655 for about 1 second. The 
WPS button will start to blink.
Step 3 - Allow up to 1 minute to configure. Once the WPS light stops blinking, you will be connected and your wireless connection will be secure 
with WPA2.
Connect to a Wireless Network  
						

							92D-Link DIR-655 User Manual
Section 4 - Connecting to a Wireless Network
It is recommended to enable wireless security (WPA/WPA2) on your wireless router or access point before configuring your wireless adapter. If you 
are joining an existing network, you will need to know the security key or passphrase being used.
1. Click on the wireless icon in your system tray (lower-right corner).
2. The utility will display any available wireless networks in your area.
Windows® 7  
						

							93D-Link DIR-655 User Manual
Section 4 - Connecting to a Wireless Network
3. Highlight the wireless network (SSID) you would like to connect to and click 
the Connect button.
 If you get a good signal but cannot access the Internet, check your TCP/IP 
settings for your wireless adapter. Refer to the Networking Basics section in 
this manual for more information.
4. The following window appears while your computer tries to connect to the 
router.  
						

							94D-Link DIR-655 User Manual
Section 4 - Connecting to a Wireless Network
5. Enter the same security key or passphrase that is on your router and click 
Ok.
It may take 20-30 seconds to connect to the wireless network. If the connection 
fails, please verify that the security settings are correct. The key or passphrase 
must be exactly the same as on the wireless router.  
						

							95D-Link DIR-655 User Manual
Section 4 - Connecting to a Wireless Network
Windows Vista®
Windows Vista users may use the built-in wireless utility. If you are using another company’s utility, please refer to the user manual of your wireless 
adapter for help with connecting to a wireless network. Most utilities will have a “site survey” option similar to the Windows Vista utility as seen below.
Right-click on the wireless computer icon in your system tray (lower-right corner 
next to the time). Select Connect to a network.
If you receive the Wireless Networks Detected bubble, click on the center of 
the bubble to access the utility.
         or
The utility will display any available wireless networks in your area. Click on a 
network (displayed using the SSID) and click the Connect button.
If you get a good signal but cannot access the Internet, check you TCP/IP settings 
for your wireless adapter. Refer to the Networking Basics section in this manual 
for more information.  
						

							96D-Link DIR-655 User Manual
Section 4 - Connecting to a Wireless Network
Configure Wireless Security
It is recommended to enable wireless security (WPA/WPA2) on your wireless router or access point before configuring your wireless adapter. If you 
are joining an existing network, you will need to know the security key or passphrase being used.
2. Highlight the wireless network (SSID) you would like to connect to and 
click Connect.
1. Open the Windows Vista® Wireless Utility by right-clicking on the wireless 
computer icon in your system tray (lower right corner of screen). Select 
Connect to a network.