D-Link Dir 600m Instalation Manual

							21
D-Link DIR-600 User Manual
Section 3 - Coniguration
Select Dynamic   (most  common)  or  Static.  Select  Static  if  your 
ISP  assigned  you  the  IP  address,  subnet  mask,  gatew ay,  and 
DNS server addresses. 
Enter your PPPoE user name.
Enter  your  PPPoE  password  and  then  retype  the  passw ord  in 
the next box.
Enter the ISP Service Name (optional).
Enter the IP address (Static PPPoE only).
Enter  the  Primary  and  Secondary  DNS  Server  Addresse s  (Static 
PPPoE only).
Enter a maximum idle time during which the Internet connection  
is  m a i n t a i n e d   d u r i n g   i n a c t i v i t y.   To   d i s a b l e   t h i s   f e a t u r e , 
enable Auto-reconnect. 
Maximum  Transmission  Unit  -  You  may  need  to  change  the 
MTU  for  optimal  performance  with  your  specific  ISP.  1492   is 
the default MTU.
Select either  Always-on, Manual , or Connect-on  demand .
PPPoE:
User Name: Password:
Service฀Name: IP Address: DNS฀
Addresses:
Maximum Idle  Time:
MTU:
Connection 
Mode Select:
Internet Setup
PPPoE 
Choose  PPPoE  (Point  to  Point  Protocol  over  Ethernet)  if  your  ISP  uses  a  PPPoE  connection.  Your  ISP  will  provide  
you  with  a  username  and  password.  This  option  is  typically  used  for  DSL  services.  Make  sure  to  remove  your  PPPoE 
software from your computer. The software is no longer needed and will not work through a router.  
						

							22
D-Link DIR-600 User Manual
Section 3 - Coniguration
Select Dynamic   (most  common)  or  Static.  Select  Static  if 
your  ISP  assigned  you  the  IP  address,  subnet  mask,  g ateway, 
and DNS server addresses. 
Enter the IP address (Static PPTP only).
Enter  the  Pr imar y  and  S econdar y  DNS  S er ver  Addresse s 
(Static PPTP only).
Enter the Gateway IP Address provided by your ISP.
The  DNS  ser ver  information  will  be  supplied  by  your   ISP 
(Internet Service Provider.)
Enter the Server IP provided by your ISP (optional). 
Enter your PPTP account name. 
Enter  your  PPTP  password  and  then  retype  the  passwo rd 
in the next box.
E n t e r   a   m a x i m u m   i d l e   t i m e   d u r i n g   w h i c h   t h e   I n t e r n e t  
connection  is  maintained  during  inactivity.  To  disa ble  this 
feature, enable Auto-reconnect. 
Maximum  Transmission  Unit  -  You  may  need  to  change  the 
MTU for optimal performance. 
Select either Always-on, Manual, or Connect-on demand.
 
IP Address:
Subnet Mask:
Gateway:DNS:
Internet Setup PPTP
Choose  PPTP  (Point-to-Point-Tunneling  Protocol  )  if   your  ISP  uses  a  PPTP  connection.  Your  ISP  will  provide  you  with 
a username and password. This option is typically used for DSL services. 
 ver฀IP:
PPTP Account:
PPTP Password:
 
Maximum Idle  Time:
MTU:
Connect Mode:  
						

							23
D-Link DIR-600 User Manual
Section 3 - Coniguration
Select Dynamic   (most  common)  or  Static.  Select  Static 
i f   yo u r   I S P   a s s i g n e d   yo u   t h e   I P   a d d re s s,   s u b n e t   m a s k , 
gateway, and DNS server addresses. 
Enter the IP address (Static L2TP only).
Enter  the  Primar y  and  Secondar y  DNS  Ser ver  Addresse s 
(Static L2TP only).
Enter the Gateway IP Address provided by your ISP.
The  DNS  ser ver  information  will  be  supplied  by  your   ISP 
(Internet Service Provider.)
Enter the Server IP provided by your ISP (optional). 
Enter your L2TP account name. 
Enter  your  L2TP  password  and  then  retype  the  passwo rd 
in the next box.
E n te r   a   m a x i m u m   i d l e   t i m e   d u r i n g   w h i c h   t h e   I n te r n e t  
connection  is  maintained  during  inactivity.  To  disa ble  this 
feature, enable Auto-reconnect. 
Maximum  Transmission  Unit  -  You  may  need  to  change  the 
MTU for optimal performance with your speciic ISP. 
Select either Always-on, Manual, or Connect-on demand.
L 
IP Address:
Subnet Mask:
Gateway:DNS:
Server฀IP:
L2TP Account: L2TP 
Password:
Maximum Idle  Time:  
MTU:  
Connect Mode:
Internet Setup
L2TP
Choose  L2TP  (Layer  2  Tunneling  Protocol)  if  your  IS P  uses  a  L2TP  connec tion.  Your  ISP  will  provide  you   with  a 
username and password. This option is typically used for DSL services.   
						

							24
D-Link DIR-600 User Manual
Section 3 - Coniguration
Internet Setup
Dual฀Access฀(for฀Russia฀only)
There  are  two  main  steps  to  configure  a  Dual  Access   Internet  connection  for  Russia.  First,  configure  a  PPPoE  connection  (as  previously 
described  for  PPPoE  connections),  and  add  the  physi cal  WAN  IP  settings  as  instructed  from  the  ISP.  Second,  conigure  a  PPTP  connection 
(as  previously  described  for  PPTP  connections).  In  addition,  the  second  step  also  includes  an  option  t o  use  a  MAC  address  that  will  always 
be associated with the connection. The MAC address is entered manually or copied from the computer.   
						

							25
D-Link DIR-600 User Manual
Section 3 - Coniguration
Wireless Setup
Wireless  settings  for  the  router  may  be  configured  
manually  or  by  using  a  wizard.  To  use  the  wizard, 
click the  Wireless฀Connection฀Setup฀Wizard  button 
and  then  follow  the  steps  that  are  described  below. 
To  configure  the  wireless  settings  manually,  click 
the  Manual  Wireless  Connection  Setup  button. 
The  parameters  for  this  window  are  described  later 
in  this  section.  The  Wireless  Security  section  that 
directly  follows  this  Configuration  section  provide s  
additional  explanation  for  how  to  conigure  the  WEP, 
W PA ,   W PA 2 ,   a n d   W PA / W PA 2   w i r e l e s s   s e c u r i t y 
mode options. 
Click  Next to continue.
Enter  a  Wireless  Network  Name  in  the  textbox,  which 
is  also  know  as  the  SSID  and  select  the  desired  lev el 
of  wireless  security,  WEP,  WPA.  and  then  click  Next 
to continue.    
						

							26
D-Link DIR-600 User Manual
Section 3 - Coniguration 
Enter  a  Wireless  Security  Password  in  the  tex tbox  a nd  then  click 
Next  to continue.
This  window  displays  a  summary  of  your  wireless  security  settings.  
Please  print  this  out  or  record  this  information  in   a  safe  place  and 
then click  Save to continue.
The  Router  will  save  your  new  settings  and  reboot.  W hen  it  is  inished 
after 1-2 minutes, the opening Wireless Setup window is displayed.    
						

							27
D-Link DIR-600 User Manual
Section 3 - Coniguration
To  implement  Wi-Fi  protection,  or  WCN  2.0,  tick  the   Enable 
checkbox,  click  either  Generate  New  PIN or Reset  PIN  to 
Default ,  and  then  conigure  the Wi-Fi  settings  below.  Please 
see  the  Setting  Up  Wi-Fi  Protection  ( WCN  2.0  in  Win dows 
Vista)  section  later  in  this  manual  for  detailed  co niguration 
information.  
Check  the  box  to  enable  the  wireless  function.  If  y ou  do 
not  want  to  use  wireless,  uncheck  the  box  to  disable  all  the  
wireless functions. 
Ser vice  Set  Identifier  (SSID)  is  the  name  of  your  w ireless 
network .  Create  a  name  using  up  to  32  charac ters.  T he 
SSID is case-sensitive.
Indicates  the  channel  setting  for  the  DIR-600.  By  d efault 
the  channel  is  set  to  6.  The  Channel  can  be  changed  to 
fit  the  channel  setting  for  an  existing  wireless  ne twork  or 
to  customize  the  wireless  network.  The  Auto  Channel 
Selection   setting  can  be  selected  to  allow  the  DIR-600  to 
choose the channel with the least amount of interference.
Use  the  drop-down  menu  to  select  the  appropriate  Tr ansmission  Rate  in  Mbits  per  second.  Many  users  will  want  to  use  the 
default setting, Best (automatic).
Enable  Wi-Fi  Multimedia  to  enjoy  basic  quality  of  service  features.  WMM  prioritizes  traic  according  to  four  access  categories:  
voice, video, best efort, and background.  
Check  this  option  if  you  would  not  like  the  SSID  of   your  wireless  network  to  be  broadcasted  by  the  DIR -600.  If  this  option  is 
checked,  the  SSID  of  the  DIR-600  will  not  be  seen  b y  Site  Survey  utilities  so  your  wireless  clients  will  have  to  know  the  SSID 
of your DIR-600 in order to connect to it.
W 
Protected  Setup:
Enable 
Wireless 
Channel: Wireless 
Network Name:
Transmission  Rate:
WMM Enable: Enable 
Wireless:
Enable Hidden  Wireless:  
						

							28
D-Link DIR-600 User Manual
Section 3 - Coniguration 1.  To  enable  wireless  security  on  the  Router,  use 
the  drop-down  menu  to  select  the  desired  option.  
To  enable  WEP,  select  E n a b l e   W E P   W i r e l e s s 
Security (basic).
2.   Next  to  Authentication ,  select  either O p e n   
or  Shared  Key .   S h a r e d   K e y   p r o v i d e s   g r e a t e r 
security.
3.   Select  either  64Bit  or  128Bit   encryption  from  the 
drop-down menu next to  WEP Encryption. 
4.   Next  to  Default฀ Key฀Type ,  select  WEP  Key  1  and 
enter  a  WEP  key  that  you  create.  Make  sure  you 
enter  this  key  exactly  on  all  your  wireless  devices . 
You may enter up to four diferent keys either using 
Hex   or  ASCII.  Hex  is  recommended  (letters  A-F  and 
numbers  0-9  are  valid).  In  ASCII  all  numbers  and 
letters are valid.
5.   Click  Save฀ Settings   to  save  your  settings.  If  you 
are  coniguring  the  Router  with  a  wireless  adapter, 
you  will  lose  connectivity  until  you  enable  WEP  on 
your  adapter  and  enter  the  same  WEP  key  as  you 
did on the Router.
NOTE: 
I t   i s   re co m m e n d e d   to   e n a b l e   e n c r y p t i o n   o n   yo u r   w i re l e s s 
Router  before  your  wireless  network  adapters.  Please   establish 
wireless  connectivity  before  enabling  encryption.  Y our  wireless 
signal  may  degrade  when  enabling  encryption  due  to  the  added 
overhead.  
						

							29
D-Link DIR-600 User Manual
Section 3 - Coniguration 1.  To  enable  Enable  WPA/WPA2  Wireless  Security 
(enhanced).
2.   Next  to  Cipher  Type ,  select  TKIP,  AES ,  or  
AUTO.
3.  Next to  PSK/EAP , select PSK.
4.  Next to  Network Key , enter a passphrase. The key 
is an alpha-numeric   
password between 8 and 63 characters long. 
The password can include symbols (!?*&_) and 
spaces. Make sure you enter this key exactly 
the same on all other wireless clients.
5.   Click  Save฀ Settings   to  save  your  settings.  If  you 
are  coniguring  the  router  with  a  wireless  adapter, 
you  will  lose  connectivity  until  you  enable  WPA/
WPA2  (whichever  of  the  three  options  you  have 
selected  above)  on  your  adapter  and  enter  the 
same network key as you did on the router.  
						

							30
D-Link DIR-600 User Manual
Section 3 - Coniguration 1.  To  enable  WPA/WPA2  for  a  RADIUS  ser ver,  next 
to  Security  Mode ,  selec  or Enable  WPA/WPA2 
Wireless Security (enhanced).
2.   Next  to  Cipher  Type ,  select  TKIP,  AES ,  or  
Auto.
3.  Next to  PSK/EAP , select EAP.
4.  Next  to  RADIUS฀ Server฀ 1   enter  the IP  Address  
of your RADIUS server.
5.  Next to  Port, enter the port you are using with your 
RADIUS server. 1812 is the default port.
6.  Next to  Shared Secret , enter the security key.
7.  If  you  have  a  secondary  RADIUS  server,  enter  its 
IP address, port, and secret key.
8.  Click  Save฀Settings  to save your settings.