D-Link Dgs1005g 5port Manual

D-Link DGS-1005D Unmanaged Gigabit Ethernet Switch 
 
LED Indicators 
The LED indicators of the Switch include Power, and Link/Act/Speed. The following shows the LED indicators for the 
Switch along with an explanation of each indicator. 
 
 
Figure 1-2. LED Indicators 
Comprehensive LED indicators display the conditions of the Switch and status of the network. A description of these 
LED indicators follows (see LED Indicators). The LED indicators of the Switch include Power, Link/Act/Speed. The 
Cable...

D-Link DGS-1005D Unmanaged Gigabit Ethernet Switch 
 
Rear Panel Description 
DC Power Jack: 
Power is supplied through an external AC power adapter. Check the technical specification section for information about 
the AC power input voltage. 
 
 
 
Figure 1-3.  Rear panel view of the Switch 
10/100/1000BASE-T Ports: 
Five (5) Gigabit Ethernet, Auto-Negotiating ports (10/100/1000Mbps) 
Comprehensive LED indicators display the conditions of the Switch and status of the network.  
 
 
 
 
 
 
 
 
 
 
 
 
 
  

D-Link DGS-1005D Unmanaged Gigabit Ethernet Switch 
 
SECTION 2 
 
Installation 
 
 Package  Contents 
Before You Connect to the Network 
 Installing the Switch 
 Power  On 
 
Package Contents 
Open the shipping carton of the Switch and carefully unpack its contents. The carton should contain the following items: 
 
 One DGS-1005D 5-Port 10/100/1000BASE-T Gigabit Ethernet Switch 
 One external power adapter 
 Wall-mounting kit 
 CD with documentation  
 
If any item is missing or damaged, please...

D-Link DGS-1005D Unmanaged Gigabit Ethernet Switch 
 
Mounting the Switch on a Wall 
The DGS-1005D can also be mounted on a wall. Two mounting slots are provided on the bottom of the switch for this 
purpose. Please make sure that the front panel is exposed in order to view the LEDs. Please refer to the illustration below: 
A.)  Mounting on a cement wall  
1. Mount the Nylon screw anchors into a cement wall. 
2. Drive the T3 x 15L screws into the Nylon screw anchors. 
3. Hook the mounting holes of the...

D-Link DGS-1005D Unmanaged Gigabit Ethernet Switch 
 
Section 3  
Connecting The Switch 
 
Switch To End Node 
Switch To Hub or Switch 
Connecting To a Server 
 
 
Switch To End Node 
End nodes include PCs outfitted with a 10, 100, or 1000 Mbps RJ-45 Ethernet/Fast Ethernet Network Interface Card (NIC) 
and most routers. 
An end node can be connected to the Switch via a twisted-pair Category 3, 4, 5, or 5e UTP/STP cable. The end node can be 
connected to any of the ports of the Switch.   
 
 
Figure 3-1....

D-Link DGS-1005D Unmanaged Gigabit Ethernet Switch 
 
 
Figure 3-2. Switch connected to a port on a hub or switch using either a straight or crossover cable–any 
standard Ethernet cable is fine 
 
Connecting To Network Backbone or Server 
Any of the five Gigabit Ethernet ports are ideal for uplinking to a network backbone or network server.  
 
 
Figure 3-3. Connection to a Server 
 
 
 
 
  

D-Link DGS-1005D Unmanaged Gigabit Ethernet Switch 
 
Appendix A 
Technical Specifications 
 
General 
Standards: IEEE 802.3ab 1000BASE-T 
IEEE 802.3u 100BASE-TX 
IEEE 802.3 10BASE-T 
IEEE 802.3x Flow Control 
IEEE 802.1p priority Queues 
Protocol: CSMA/CD 
Data Transfer 
Rate: 10Mbps (Half-duplex)  Ethernet: 
20Mbps (Full-duplex) 
100Mbps (Half-duplex)  Fast Ethernet: 
200Mbps (Full-duplex) 
Gigabit Ethernet: 2000Mbps  (Full-duplex) 
 
Topology: Star 
Network Cables: Ethernet:  2-pair UTP Cat. 3,4,5,...

D-Link DGS-1005D Unmanaged Gigabit Ethernet Switch 
 
Performance 
Transmission 
Method: Store-and-forward 
RAM Buffer: 128KBytes per device 
Filtering Address 
Table: 4K MAC address per device 
Packet Filtering/ 
Forwarding Rate: Full wire speed 
MAC Address 
Learning: Self-learning, auto-aging  

D-Link DGS-1005D Unmanaged Gigabit Ethernet Switch 
 
Glossary 
1000BASE-SX – A short laser wavelength on multimode fiber optic cable for a maximum length of 550 meters. 
1000BASE-LX – A long wavelength for a long haul fiber optic cable for a maximum length of 10 kilometers. 
100BASE-FX – 100Mbps Ethernet implementation over fiber. 
100BASE-TX – 100Mbps Ethernet implementation over Category 5 and Type 1 Twisted Pair cabling. 
10BASE-T – The IEEE 802.3 specification for Ethernet over Unshielded Twisted...

D-Link DGS-1005D Unmanaged Gigabit Ethernet Switch 
  latency – The delay between the time a device receives a packet and the time the packet is forwarded out of the 
destination port. 
line speed – See baud rate. 
main port – The port in a resilient link that carries data traffic in normal operating conditions. 
MDI – Medium Dependent Interface. An Ethernet port connection where the transmitter of one device is connected to 
the receiver of another device. 
MDIX – Medium Dependent Interface Cross-over....