compaq prosignia 190 User Manual

MAINTENANCE & SERVICE GUIDE
PROSIGNIA NOTEBOOK 190
INDEX PAGEPRODUCT DESCRIPTIONLEGAL NOTICEHOW TO USE THIS GUIDE
REMOVAL & REPLACEMENTILLUSTRATED PARTS CATALOGTROUBLESHOOTINGSPECIFICATIONS
Product Description
Right Side Components
>Models
>Top Cover
>Top Lights
>Left & Front
Components
>Right side 
Components
>Bottom of
Unit
>Rear
Connectors
>Power
Management
 
1PCI card slot
2Stereo 
speaker & 
headphone 
jack
3Mono 
microphone 
jack
4Security 
cable slot
5RJ-45 jack 
(for internal 
modems)
6RJ-11 jack...

MAINTENANCE & SERVICE GUIDE
PROSIGNIA NOTEBOOK 190
INDEX PAGEPRODUCT DESCRIPTIONLEGAL NOTICEHOW TO USE THIS GUIDE
REMOVAL & REPLACEMENTILLUSTRATED PARTS CATALOGTROUBLESHOOTINGSPECIFICATIONS
Product Description
Bottom of Unit
>Models
>Top Cover
>Top Lights
>Left &
Front
Components
>Right side
Components
>Bottom of 
Unit
>Rear
Connectors
>Power
Management
 
1Modem/NIC/combo 
card slot cover
2Keyboard retaining 
screw
3Serial number & 
label
4Primary battery 
release latch
5Hard drive release 
latch
6Hard...

MAINTENANCE & SERVICE GUIDE
PROSIGNIA NOTEBOOK 190
INDEX PAGEPRODUCT DESCRIPTIONLEGAL NOTICEHOW TO USE THIS GUIDE
REMOVAL & REPLACEMENTILLUSTRATED PARTS CATALOGTROUBLESHOOTINGSPECIFICATIONS
Product Description
Power Management
>Models
>Top Cover
>Top Lights
>Left & Front
Components
>Right side
Components
>Bottom of
Unit
>Rear
Connectors
>Power 
ManagementWhen an electrical outlet is not available or is not convenient, the pow\
er 
management of your battery plays a crucial role in the use of your perso\...

Using a New Battery Pack
Charge the battery pack in the computers primary battery bay or MultiBa\
y while 
connected to an external power source or while docked in the optional 
convenience base.
NOTE:A new battery pack should be fully charged before it is used for the fir\
st 
time. The battery pack will work without being fully charged, but the 
battery gauge will not show an accurate charge until the battery pack 
receives its first full charge.
Charging Battery Packs
Battery packs charge in the...

MAINTENANCE & SERVICE GUIDE
PROSIGNIA NOTEBOOK 190
INDEX PAGEPRODUCT DESCRIPTIONLEGAL NOTICEHOW TO USE THIS GUIDE
REMOVAL & REPLACEMENTILLUSTRATED PARTS CATALOGTROUBLESHOOTINGSPECIFICATIONS
Power Management Continued
Storing a Battery Pack
CAUTION:  to prevent damage to a battery pack, do not expose it to high temperatu\
res for extended periods
of time.
If the computer will be unused and unplugged from an external power sour\
ce for more than two weeks, remove and store 
the battery packs.
Maximizing...

cigarette lighter receptacle.
Plug an optional aircraft power adapter into the power connector on the \
computer and into the in-seat power supply 
available on some commercial aircraft. 
An optional aircraft power adapter can be used to run the computer, but \
cannot be used to charge a battery pack. 
If a charged battery pack is available, press the  suspend button to initiate Suspend (standby), then remove the discharged
battery pack and insert a charged battery pack. 
If neither external power nor a...

Calibration increases the accuracy of all battery charge displays. The c\
alibration utility supports all battery packs that can be 
used in the computer. Use the calibration utility both to check the cali\
bration of a battery pack and to calibrate or 
recalibrate a battery pack. A battery pack cannot be calibrated unless t\
he utility reports that it needs calibration. 
The following is a list of important information concerning the calibrat\
ion of a battery pack:A new battery pack can be charged,...

MAINTENANCE & SERVICE GUIDE
PROSIGNIA NOTEBOOK 190
INDEX PAGEPRODUCT DESCRIPTIONLEGAL NOTICEHOW TO USE THIS GUIDE
REMOVAL & REPLACEMENTILLUSTRATED PARTS CATALOGTROUBLESHOOTINGSPECIFICATIONS
Removal & Replacement
Serial Number Location
This section explains the removal and replacement procedures for the com\
puter.
>Preliminaries
>Serial 
Number 
Location
>Battery Pack
>DualBay
Drive
>MultiBay
Drive
>Hard Drive
>Modem
>Keyboard
>Memory
Module
>LED Cover
>RTC battery
>Display Panel
Assembly
>Button Board...