compaq presario 2800 User Manual

Removal and Replacement Procedures
Maintenance and Service Guide5–13
3. Remove the PM2.0 × 5.0 screw 1 that secures the mini PCI 
compartment cover to the base enclosure (Figure 5-10).
4. Lift the front edge of the cover and swing it back 2.
5. Remove the cover 3.
Figure 5-10. Removing the Mini PCI Communications 
Slot Cover
✎Mini PCI compartment covers are available with silver finish for 
Presario 2800 models and carbon finish for Evo Notebook 
N800c, N800v, and N800w models. These covers are included...

5–14Maintenance and Service Guide
Removal and Replacement Procedures
6. Disconnect the modem cable from the modem board 1 
(Figure 5-11).
✎The modem cable spare part number is 285268-001.
7. Spread the retaining tabs to release the mini PCI 
communications board 2. The board tilts up at a 
45-degree angle.
8. Remove the board by pulling it away from the connector 
at a 45-degree angle 3.
Figure 5-11. Removing a Mini PCI Communications Board
Reverse the above procedure to install a mini PCI...

Removal and Replacement Procedures
Maintenance and Service Guide5–15
5.7 Connector Cover
✎The connector cover is available with silver finish for Presario 
2800 models and carbon finish for Evo Notebook N800c, N800v, 
and N800w models. This cover is included in the Miscellaneous 
Plastics/Hardware Kit, spare part number 285261-001 for 
Presario 2800 models, and spare part number 286868-001 for Evo 
Notebook N800c, N800v, and N800w models.
1. Prepare the computer for disassembly (Section 5.3).
2. Turn the...

5–16Maintenance and Service Guide
Removal and Replacement Procedures
5.8 LED Cover
1. Prepare the computer for disassembly (Section 5.3).
2. Turn the computer bottom side up with the rear panel facing 
forward.
3. Remove the two black PM2.0 × 10.0 screws that secure the 
LED cover to the base enclosure (Figure 5-13).
Figure 5-13. Removing the LED Cover Screws
4. Turn the computer top side up with the front facing forward.
5. Open the computer.
LED Cover
Spare Part Number Information
LED cover288503-001...

Removal and Replacement Procedures
Maintenance and Service Guide5–17
6. Use a flat-bladed tool to pry forward on the four clips on the 
LED cover 1 (Figure 5-14).
7. Press the 
esc and F1 keys to reveal the left notch 2 in the LED 
cover.
8. Insert a flat-bladed tool into the left notch and lift the left side 
of the LED cover 3.
9. Press the 
Pause and Del keys to reveal the right notch 4 in the 
LED cover.
10. Insert a flat-bladed tool into the right notch and lift the right 
side of the LED cover 5....

5–18Maintenance and Service Guide
Removal and Replacement Procedures
5.9 Keyboard
Keyboards
Spare Part Number Information
Keyboards (for use with TouchPad models only)
Arabic
Belgian
Brazilian
Chinese
Czech
Danish
French
French Canadian
German
Greek/Polish
Hebrew
Hungarian
International
Italian285280-171
285280-181
285280-201
285280-AA1
285280-221
285280-081
285280-051
285280-121
285280-041
285280-151
285280-BB1
285280-211
285280-002
285280-061Korean
Latin American Spanish
Norwegian
Portuguese
Russian...

Removal and Replacement Procedures
Maintenance and Service Guide5–19
1. Prepare the computer for disassembly (Section 5.3).
2. Remove the LED cover (Section 5.8).
3. Lift the back edge of the keyboard 1 (Figure 5-15).
4. Slide the keyboard toward the back of the computer 2.
5. Lift the back edge of the keyboard and swing it forward 3 
until it rests on the palm rest.
Figure 5-15. Releasing the Keyboard 
268135-002.book  Page 19  Thursday, October 24, 2002  4:10 PM 

5–20Maintenance and Service Guide
Removal and Replacement Procedures
6. Remove the two PM2.0 × 4.0 screws 1 that secure the 
keyboard shield to the base enclosure (Figure 5-16).
7. Remove the keyboard shield 2.
Figure 5-16. Removing the Keyboard Shield
✎The keyboard shield is included in the Miscellaneous 
Plastics/Hardware Kit, spare part numbers 285261-001 and 
286868-001.
268135-002.book  Page 20  Thursday, October 24, 2002  4:10 PM 

Removal and Replacement Procedures
Maintenance and Service Guide5–21
8. Release the ZIF connector 1 to which the keyboard cable is 
connected and disconnect the keyboard cable 2 from the 
system board (Figure 5-17).
9. Remove the keyboard.
Figure 5-17. Removing the Keyboard
Reverse the above procedure to install the keyboard.
268135-002.book  Page 21  Thursday, October 24, 2002  4:10 PM 

5–22Maintenance and Service Guide
Removal and Replacement Procedures
5.10 Display
1. Prepare the computer for disassembly (Section 5.3).
2. Remove the LED cover (Section 5.8).
3. Close the computer and position the computer so the rear 
panel faces forward.
Displays
Spare Part Number Information
Displays
Contain parts with carbon finish for use with
Evo Notebook N800c, N800v, and N800w models
15-inch, UXGA
15-inch, SXGA+
15-inch, XGA
14-inch, XGA
Contain parts with silver finish for use with
Presario...