compaq presario 1200 series User Manual

							PRESARIO NOTEBOOK MAINTENANCE AND SERVICE GUIDE 1200XL SERIESREMOVAL SEQUENCE 21
Presario 1200 Series
Models: XL101-XL113, XL115, XL118-XL127
Removing the Hard Drive Mounting Bracket
To remove the hard drive mounting bracket, remove four screws from the top of the hard 
drive.
To replace the hard drive and mounting bracket, reverse these procedures. 
						

							22 REMOVAL SEQUENCEPRESARIO NOTEBOOK MAINTENANCE AND SERVICE GUIDE 1200XL SERIES
Presario 1200 Series
Models: XL101-XL113, XL115, XL118-XL127
Removing the CD/DVD Drive
Note: Illustrations may show parts removed that are not part of this procedure. It is 
necessary to remove only the parts listed in the written procedure.
To remove the CD/DVD Drive, complete the following steps:
1. Prepare the computer for disassembly (pg 10
).
2. Remove the palmrest cover with TouchPad (pg 13
).
3. Remove the keyboard (pg 15
).
4. Remove the heatspreader (pg 17
).
5. Close the display and turn the Notebook over (upside down).
6. Remove two screws from the underside of the Notebook that secure the CD or DVD 
drive to the chassis.
Continued on next page. 
						

							PRESARIO NOTEBOOK MAINTENANCE AND SERVICE GUIDE 1200XL SERIESREMOVAL SEQUENCE 23
Presario 1200 Series
Models: XL101-XL113, XL115, XL118-XL127
7. Turn the Notebook over (right side up) and open the display.
8. Remove two screws located at the back of the CD or DVD drive.
9. Disconnect the CD/DVD drive cable from the CD or DVD drive.
10. Remove the CD or DVD drive from the chassis.
To replace the CD/DVD drive, reverse these procedures. 
						

							24 REMOVAL SEQUENCEPRESARIO NOTEBOOK MAINTENANCE AND SERVICE GUIDE 1200XL SERIES
Presario 1200 Series
Models: XL101-XL113, XL115, XL118-XL127
Removing the Battery Charger Board
(Voltage Converter Board)
Note: Illustrations may show parts removed that are not part of this procedure. It is 
necessary to remove on the parts listed in the written procedure.
To remove the battery charger board, complete the following:
1. Prepare the Notebook for disassembly (pg 10
).
2. Remove the palmrest cover with TouchPad (pg 13
).
3. Remove the hard drive (pg 19
).
4. Remove one screw from the battery charger board, unplug the board from the 
connector on the system board, and lift it out of the chassis.
To replace the battery charger board, reverse these procedures.
Important: When replacing the battery charger board, ensure that the pins are aligned 
with the connector on the system board. 
						

							PRESARIO NOTEBOOK MAINTENANCE AND SERVICE GUIDE 1200XL SERIESREMOVAL SEQUENCE 25
Presario 1200 Series
Models: XL101-XL113, XL115, XL118-XL127
Removing the Modem
To remove the modem, complete the following steps:
1. Prepare the computer for disassembly (pg 10
).
2. Remove the palmrest cover with TouchPad (pg 13
).
3. Remove the keyboard (pg 15
).
4. Remove the heatspreader (pg 17
).
5. Remove three screws securing the modem, and disconnect the modem from the 
connector on the system board.
Continued on next page. 
						

							26 REMOVAL SEQUENCEPRESARIO NOTEBOOK MAINTENANCE AND SERVICE GUIDE 1200XL SERIES
Presario 1200 Series
Models: XL101-XL113, XL115, XL118-XL127
6. Disconnect the modem cable from the modem.
To replace the modem, reverse these procedures. 
						

							PRESARIO NOTEBOOK MAINTENANCE AND SERVICE GUIDE 1200XL SERIESREMOVAL SEQUENCE 27
Presario 1200 Series
Models: XL101-XL113, XL115, XL118-XL127
Removing the Display Panel Assembly
Note: Illustrations may show parts removed that are not part of this procedure. It is 
necessary to remove only the parts listed in the written procedure.
To remove the display panel assembly, complete the following steps:
1. Prepare the computer for disassembly (pg 10
).
2. Remove the palmrest cover with TouchPad (pg 13
).
3. Remove the keyboard (pg 15
).
4. Remove the heatspreader (pg 17
).
5. Disconnect the backlight cable attached to the display panel assembly from the 
connector on the system board.
Continued on next page. 
						

							28 REMOVAL SEQUENCEPRESARIO NOTEBOOK MAINTENANCE AND SERVICE GUIDE 1200XL SERIES
Presario 1200 Series
Models: XL101-XL113, XL115, XL118-XL127
6. For units with Thin Film Transistor (TFT) displays, disconnect the display data cable 
from the LVDS connector as shown in 
1 and 2 below. For units with High-
Performance Addressing (HPA) displays, disconnect the display data cable from the 
CMOS connector as shown in 
3 below.
Continued on the next page. 
						

							PRESARIO NOTEBOOK MAINTENANCE AND SERVICE GUIDE 1200XL SERIESREMOVAL SEQUENCE 29
Presario 1200 Series
Models: XL101-XL113, XL115, XL118-XL127
7. Close the display, carefully push in 1 on the hinge covers, and then lift 2 the covers 
off the hinges.
8. Support the back of the display panel and remove two screws from each of the hinges.
Continued on the next page. 
						

							30 REMOVAL SEQUENCEPRESARIO NOTEBOOK MAINTENANCE AND SERVICE GUIDE 1200XL SERIES
Presario 1200 Series
Models: XL101-XL113, XL115, XL118-XL127
9. If the display data cable has the LVDS connector on the end as shown below, remove 
the connector by 
1 grasping the edges of the connector and 2 gently pulling out the 
cable.
Ä
ÄÄ Ä
CAUTION: For TFT displays, the connector on the end of the flex cable must be 
removed before the cable can be routed through the slot on the upper CPU cover.
10. Gently pull the flex data cable and backlight cable attached to the display panel 
through the slot on the upper CPU cover and lift the display panel off of the unit.
Important: When removing the display panel assembly, take note of the correct routing 
position for the display flex cable for use during replacement.
Note: For TFT displays, Compaq recommends replacing the LVDS connector on the end 
of the display flex cable after the display panel assembly has been removed from the 
unit.
To replace the display panel, reverse these procedures.