Cobra 2010wx Base Cb Tranciever Manual

							      Section VI Appendix  (Continued)
        Fig. 4. Microphone plug pin numbers viewed from rear of pin receptacle.
Be sure that the housing and the knurled ring of Fig. 3 are pushed back onto the
microphone cable before starting to solder. If the washer is not captive to the pin
receptacle body, make sure that it is  placed on the threaded portion of the pin
receptacle body before soldering.
If the microphone jack is used to hold the pin receptacle during soldering operation,
best results are obtained when the connections to pins 1 and 3 are made first and then
the connections to pins 2, 4 and 5. Use a minimum amount of solder and be careful
to prevent excessive solder accumulation on pins, which could cause a short between
the pin and the microphone plug housing.
6. When all soldering connections to the pins of the microphone are complete,
push the knurled ring and the housing forward and screw the housing onto the
threaded portion of the pin receptacle body. Note the location of the screw
clearance hole in the plug housing with respect to the threaded hole in the pin
receptacle body. When the housing is completely threaded into the pin
receptacle body, a final fraction of a turn either clockwise or counterclockwise
may be required to align the screw hole with the threaded hole in the pin
receptacle body. When these are aligned, the retaining screw is then screwed
into place to secure the housing to the pin receptacle body.
7. The two cable clamp retainer screws should now be tightened to secure the
housing to the microphone cord. If the cutting directions have been carefully
followed, the cable clamp should secure to the insulation jacket of the micro-
phone cable.
8. Upon completion of the microphone plug wiring, connect and secure the
microphone plug in the transceiver.
19 
						

							20
      Section VI Appendix  (Continued)
Fig. 2. Microphone Cable Preparation
To wire the microphone cable to the plug provided, proceed as follows.
Fig. 3. Microphone plug wiring.
1. Remove the retaining screw.
2. Unscrew the housing from the pin receptacle body.
3. Loosen the two cable clamp retainer screws.
4. Feed the microphone cable through the housing, knurled ring and washer as
shown Fig. 3B.
5. The wires must now be soldered to the pins as indicated in the above wiring tables.
If a vise or clamping tool is available it should be used to hold the pin receptacle
body during the soldering operation, so that both hands are free to perform the
soldering. If a vise or clamping tool  is not available, the pin receptacle body can
be held in a stationary position by inserting it into the microphone jack on the front
panel. The numbers of the pins of the microphone plug are shown in Fig 4, as
viewed from the back of the plug. Before soldering the wire to the pins, pre-tin the
wire receptacle of each pin of the plug. 
						

							21
If You Need Service
If You Think You Need Service, Call 773-889-3087
You may be asked to send your unit to the Cobra factory. It will be  necessary to
furnish the following,  in order to have the product serviced and returned.
1.For Warranty Repair,  include some form of proof-of-purchase, such as  a mechanical
reproduction or carbon or a sales receipt. If you send the original receipt it cannot be
returned.
2.Send the entire product. Must include CB unit and microphone.
3.Enclose a description of what is happening with the unit. Include a typed or clearly
printed name and address of where the unit is to be  returned.
4.Pack unit securely to prevent damage in transit. If possible, use the original packing
material.
5.Ship prepaid and insured by way of a traceable carrier  ( to  avoid  loss in transit)  such
as United Parcel Service (UPS), Roadway Parcel Service (RPS) or First Class Insured
Mail to Cobra  Factory  Service,  Cobra Electronics Corporation, 6500 W. Cortland
St., Chicago, IL 60707. Cobra is not responsible for units not received if package has
not been properly insured.
6.If the unit is in warranty, upon receipt of your unit it will either be repaired or exchanged
depending on the model. Please allow  approximately 3 to 4 weeks before contacting
us for status. If the unit is out of warranty a letter will automatically be sent informing
you of the repair charge or replacement charge. If you have any questions, please call
773-889-3087 for assistance.
For technical assistance, please call our Automated Help Desk
which can assist you by answering the most frequently asked
questions about Cobra products.
(773) 889-3087
24 hours a day, 7 days a week.
A Consumer Service Representative
 can be reached through this same number
8:00 am - 8:00 pm, Monday through Friday, CST.
Technical  assistance is also available on-line in the
Frequently Asked Question (FAQ) section at
www.cobraelec.com or by e-mail to [email protected] 
						

							WARRANTY
22 Limited Two Year Warranty
COBRA ELECTRONICS CORPORATION warrants that its COBRA citizens band (CB)
radio, and the component parts thereof, will be free of defects in workmanship and
materials for period of two (2) year from the date of first consumer purchase. This warranty
may be enforced by the first consumer purchaser, provided that the product is utilized
within the U.S.A.
COBRA will, without charge, repair or replace, at its option, defective citizens band (CB)
products or component parts upon delivery to the COBRA factory Service Department,
accompanied by proof of the date of first consumer purchase, such as a duplicated copy
of a sales receipt.
You must pay any initial shipping charges required to ship the product for warranty service.
The return charges will be at CobraÕs expense, if the product is repaired or replaced under
warranty. For further details concerning procedures for obtaining service, see the ÒIf You
Need ServiceÓ section of the OwnerÕs Manual.
Exclusions: This limited warranty does not apply; 1) to any product damaged by accident;
2) in the event of misuse or abuse of the product or as a result of unauthorized alterations
or repairs; 3) if the serial number has been altered, defaced or removed; 4) if the owner
of the product resides outside the U.S.A.
All implied warranties, including warranties of merchantability and fitness for a
particular purpose are limited in duration to the length of this warranty.
COBRA shall not be liable for any incidental, consequential or other damages; including,
without limitation, damages resulting from loss of use or cost of installation.
Some states do not allow limitations on how long an implied warranty lasts and/or do
not allow the exclusion or limitation of incidental or consequential damages, so the
above limitations may not apply to you.
This limited warranty gives you specific legal rights, and you may also have other rights
which vary from state to state.
Cobra Electronics Corporation,
6500 W. Cortland Street,  Chicago, IL 60707 
						

							Amount
(Tax if applicable 
HH)
Shipping / handling           $3.50
Total
HH
        Description                                    Part No.          Cost Ea.  X  Qty.  =   Amount
    COBRA CB RADIO ACCESSORIES
CUT ALONG         DOTTED LINE
FOLD THIS FLAP OVER BOTTOM AND TAPE IT DOWN AND SIDES TO CLOSE
FOLD ALONG     THIS LINE FIRST
FOLD ALONG       THIS LINE SECOND
Allow 4 to 6 weeks delivery. Offer valid in Continental U.S. only. City                                  State         Zip
Please print clearlyÑthis is shipping label.
Name
Address (Not P.O. Box)
DC POWER CORD for 2010 GTL WX PC-2010 $5.00
CA-78, MOBILE POWER MICROPHONE
Amplified Power Microphone with 5-pin connector
for 2010 GTL WX CA-78 $39.95 CA-72 BASE STATION MICROPHONE with
5-pin connector for 2010 GTL WX CA-72 $53.95 AT-55 Cellular-Style Glass-Mount Antenna
for 2010 GTL WX AT-55 $24.95
ATW-400 DUAL BAND ANTENNA,  Magnetic
mount with 15 RG58U Cable and PL-259 connector ATW-400 $39.95
ATW-480 DUAL BAND ANTENNA 
Truck mirror
mount with 1.2 meter 3/8 fiberglass whip,
weather tunable ATW-480 $29.95
ATW-500 DUAL BAND ANTENNA 48 whip, magnet
mount with 16Õ 8240 cable & PL-259 connector ATW-500 $49.95
ATW-2000 DUAL BAND ANTENNA Truck mirror
mount, 48 stainless steel whip, weather tunable ATW-2000 $69.95 ATW-1000 DUAL BAND ANTENNA Magnet mount
with16 8240 cable and PL-259 connector ATW-1000 $89.95
93 ATW INDOOR DUAL BAND (CB/WEATHER)
BASE STATION ANTENNA with 15 ft. coaxial cableATW-93 $44.95
HH Illinois residents add 7%       HH Cook County, IL residents additional .75% (7.75% total)               HH Chicago, IL residents additional 1% (8.75% total)HH Indiana residents add 5%HH Michigan residents add 6 %HH Ohio residents add 6%HH Wisconsin residents add appropriate %
Cobra Accessories Dept.
6500 W. Cortland St., Chicago, IL 60707
or call 773-889-3087 for credit card orders.
 Make check or money order (no stamps) payable to : 
						

							PRINTED IN MALAYSIA            ©COBRA ELECTRONICS CORP. 1996         480-114-P-001FOLD HERE TO MAKE SELF MAILER
PLACE
STAMP
 HERE
Cobra®
Cobra Electronics Corporation
6500 W. Cortland Street
Chicago, IL 60707