Cisco Sg3008 Manual

Smartport
Auto Smartport
166 Cisco Small Business 200, 300 and 500 Series Managed Switch Administration Guide (Internal Version) 
11
NOTEIf only the IP Phone and Host bits are set, then the Smartport type is 
ip_phone_desktop.
Multiple Devices Attached to the Port
The device derives the Smartport type of a connected device via the capabilities 
the device advertises in its CDP and/or LLDP packets.
If multiple devices are connected to the device through one interface, Auto 
Smartport considers each...

Smartport
Error Handling
Cisco Small Business 200, 300 and 500 Series Managed Switch Administration Guide (Internal Version)  167
11
 
Persistent status of an interface is disabled, the interface reverts to the default 
Smartport type when the attaching device to it ages out, the interface goes down, 
or the device is rebooted. Enabling Persistent status on an interface eliminates the 
device detection delay that otherwise occurs.
NOTEThe persistence of the Smartport types applied to the interfaces are...

Smartport
Common Smartport Tasks
168 Cisco Small Business 200, 300 and 500 Series Managed Switch Administration Guide (Internal Version) 
11
Common Smartport Tasks
This section describes some common tasks to setup Smartport and Auto 
Smartport.
Workflow1: To globally enable Auto Smar tpor t on the device, and to 
configure a por t with Auto Smar tpor t, perform the following steps:
STEP 1To enable the Auto Smartport feature on the device, open the Smartport > 
Properties page. Set Administrative Auto...

Smartport
Common Smartport Tasks
Cisco Small Business 200, 300 and 500 Series Managed Switch Administration Guide (Internal Version)  169
11
 
Workflow3: To adjust Smar tpor t macro parameter defaults and/or bind a 
user-defined macro pair to a Smar tpor t type, perform the following 
steps:
Through this procedure you can accomplish the following:
•View the macro source.
•Change parameter defaults.
•Restore the parameter defaults to the factory settings.
•Bind a user-defined macro pair (a macro and its...

Smartport
Configuring Smartport Using The Web-based Interface
170 Cisco Small Business 200, 300 and 500 Series Managed Switch Administration Guide (Internal Version) 
11
A second method of resetting single or multiple unknown interfaces is:
STEP 1In the Interface Settings page, select the Port Type equals to checkbox.
STEP  2Select Unknown and click Go.
STEP  3Click Reset All Unknown Smartports. Then reapply the macro as described above.
TIPThe reason that the macro failed might be a conflict with a...

Smartport
Configuring Smartport Using The Web-based Interface
Cisco Small Business 200, 300 and 500 Series Managed Switch Administration Guide (Internal Version)  171
11
 
-Enable by Auto Voice VL AN—This enables Auto Smartport, but puts it in 
operation only when Auto Voice VLAN is also enabled and in operation.   
Enable by Auto Voice VLAN is the default.
•Operational Auto Smartport—Displays the Auto Smartport status.
•Auto Smartport Device Detection Method—Select whether incoming 
CDP, LLDP, or both...

Smartport
Configuring Smartport Using The Web-based Interface
172 Cisco Small Business 200, 300 and 500 Series Managed Switch Administration Guide (Internal Version) 
11
NOTEChanges to Auto Smartport types cause the new settings to be applied to 
interfaces which have already been assigned that type by Auto Smartport. In this 
case, binding an invalid macro or setting an invalid default parameter value causes 
all ports of this Smartport type to become unknown. 
STEP 1Click Smartport > Smartport Type...

Smartport
Configuring Smartport Using The Web-based Interface
Cisco Small Business 200, 300 and 500 Series Managed Switch Administration Guide (Internal Version)  173
11
 
NOTEThere is no method to validate macro parameters because they do not have a type 
association. Therefore, any entry is valid at this point. However, invalid parameter 
values may cause errors to occur when the Smartport type is assigned to an 
interface, applying the associated macro.
Smartport Interface Settings
Use the Interface...

Smartport
Configuring Smartport Using The Web-based Interface
174 Cisco Small Business 200, 300 and 500 Series Managed Switch Administration Guide (Internal Version) 
11
The Reapply action also adds the interface to all newly-created VLANs.
STEP  2Smartport Diagnostic.
If a Smartport macro fails, the Smartport Type of the interface is Unknown. Select 
an interface which is of unknown type and click Show Diagnostic. This displays 
the command at which application of the macro failed. See the workflow area...

Smartport
Built-in Smartport Macros
Cisco Small Business 200, 300 and 500 Series Managed Switch Administration Guide (Internal Version)  175
11
 
•Persistent Status—Select to enable the Persistent status. If enabled, the 
association of a Smartport type to an interface remains even if the interface 
goes down, or the device is rebooted.   Persistent is applicable only if the 
Smartport Application of the interface is Auto Smartport. Enabling Persistent 
at an interface eliminates the device detection...