Cisco Router 800 Series Software Configuration Guide

 
E-5
Cisco 800 Series Software Configuration Guide
78-5372-06
Appendix E      ISDN BRI Cause Values
65 0041 Bearer capability not 
implemented.The network cannot provide the bearer 
capability (BC) requested by the user.
66 0042 Channel type not 
implemented.The network or the destination 
equipment does not support the requested 
channel type.
69 0045 Requested facility not 
implemented.The remote equipment does not support 
the requested supplementary service.
70 0046 Only restricted digital...

 
Appendix E      ISDN BRI Cause Values
E-6
Cisco 800 Series Software Configuration Guide
78-5372-06
85 0055 No call suspended. The network received a call resume 
request when there was not a suspended 
call pending. This might be a transient 
error that will be resolved by successive 
call retries.
86 0056 Call having requested call 
identity has been cleared.The network received a call resume 
request. The call resume request 
contained a Call Identity information 
element, which once indicated a...

 
E-7
Cisco 800 Series Software Configuration Guide
78-5372-06
Appendix E      ISDN BRI Cause Values
97 0061 Message type nonexistent or 
not implemented.The receiving equipment received an 
unrecognized message, either because 
the message type was invalid or because 
the message type was valid but not 
supported. Cause 97 is due to either a 
problem with the remote configuration or 
a problem with the local D channel.
98 0062 Message incompatible with 
call state or message type 
nonexistent.The remote...

 
Appendix E      ISDN BRI Cause Values
E-8
Cisco 800 Series Software Configuration Guide
78-5372-06
127 007F Interworking, unspecified. An event occurred, but the network does 
not provide causes for the action that it 
takes. The precise problem is unknown.
UNKNOWN N/A Unknown or local error. An event occurred, but the network does 
not provide causes for the action that it 
takes. The precise problem is unknown.
1. Cause value is shown in decimal format.
2. Hex value = hexadecimal translation of the...

IN-1
Cisco 800 Series Software Configuration Guide
78-5372-06
INDEX
Symbols
? commandA-6
Numerics
5ESS custom switchD-4, D-8, D-13
A
AAL1-13
AAL3/41-13
AAL51-13
AAL5MUXPPP encapsulation configuration 
example
7-12
AAL5SNAP encapsulation configuration 
example
7-11, 7-15
abbreviating commandsA-9
access lists
configuring
7-34 to 7-35
for UDP broadcasts control3-27
IP traffic3-30
network access restrictions3-31
session filtering1-25
ACK bits1-25
activating the POTS dial feature6-20
addressing,...

Index
IN-2
Cisco 800 Series Software Configuration Guide
78-5372-06
queues1-22
troubleshooting commands9-6 to 9-14
ATM adaptation layer
See AAL
ATM interface
See ATM
ATM OAM F5 continuity check support, 
configuring
8-44
audience, userxxviii
authentication protocols
See PPP authentication protocols
B
basic calls, making6-13
basic telephone service
See POTS dial peer
b flash command
B-7
boot commandsB-7
bootstrap program
See ROM monitor
bridge, replacing
4-9 to 4-12
bridging
configuration example
7-15...

IN-3
Cisco 800 Series Software Configuration Guide
78-5372-06
Index
configuring2-9 to 2-33, 3-12
description1-10 to 1-11
recommanded protocol3-5
Cisco 800 series and Cisco SOHO series 
routers, overview
1-2
Cisco 831 router VPN connections4-5
Cisco documentationxxxiii
Cisco Easy VPN Client, configuring8-49
Cisco IOS software documentation, 
accessing
xxxiii
class-based weighted fair queuing
See CBWFQ
command(s)
copy running-config startup-config
A-10
debug atm errors9-11
debug atm events9-12
debug atm...

Index
IN-4
Cisco 800 Series Software Configuration Guide
78-5372-06
undoingA-9
xmodemB-13
command variables
listing
A-7
TFTP downloadB-7
committed access rate
See CAR
Common Application Programming Interface
See CAPI
common applications
6-69
configuration
before configuring
2-1
caller ID6-47
caller ID for the Net3 switch6-47
call forwarding method6-49
call forwarding service6-49
CHAP2-26, 3-12
CLIR6-51
feature by feature7-1, 8-1
PIAFS6-70
prefix filter6-53
prefix number6-52
private IP network to...

IN-5
Cisco 800 Series Software Configuration Guide
78-5372-06
Index
DHCP server7-30
dial backup4-24, 7-53 to 7-58
dialer interface7-6
dial-on-demand routing for PPPoE 
client
8-52
dial peers7-74
dynamic routing7-14 to 7-20
Easy IP (Phase 1)7-24 to 7-26
Easy IP (Phase 2)7-26 to 7-33
EIGRP, IP7-20 to 7-21
Ethernet interface4-21, 4-57, 7-4
extended access list7-34
global parameters7-4
H.3237-74 to 7-76
interleaving7-72
IP EIGRP7-20 to 7-21
IP parameters7-63
IP Precedence7-72 to 7-73
local call...

Index
IN-6
Cisco 800 Series Software Configuration Guide
78-5372-06
debug ATM commands9-10 to 9-14
debug atm errors command9-11
debug atm events command9-12
debug atm packet command9-13 to 9-14
debug commands, ROM monitorB-14 to B-16, 
B-18
debug message
cause values
6-26
CSM events6-25
CSM states6-23
formats6-22
debug POTS commands6-51
default settings, RCAPI5-5
destination-pattern command1-19
dev commandB-7
DHCP
configuring DHCP server
4-56
IP address assignment4-56
DHCP and Easy IP (Phase 2)1-17
DHCP...