Cisco Router 800 Series Software Configuration Guide

xix
Cisco 800 Series Software Configuration Guide
78-5372-06
Contents
Configuring the Service Assurance Agent8-27
Configuring Secure Shell8-28
Configuring IP Named Access Lists8-29
Configuring International Phone Support8-29
Configuration Example8-30
International Tone, Cadence, Ring Frequency, and Impedance Support8-31
Configuring a Regional Analog Voice Tone8-31
Configuring an FXS Ring Cadence8-32
Configuring the FXS Voice Port Ring Frequency8-33
Configuring the Terminating Impedance8-33
International...

Contents
xx
Cisco 800 Series Software Configuration Guide
78-5372-06
Configuring Continuity Checking Debugging8-47
Configuring Generation of End-to-End F5 OAM Loopback Cells8-47
Example Output8-48
Configuring RADIUS Support8-49
Configuring Cisco Easy VPN Client8-49
Configuration Example8-50
Configuring Dial-on-Demand Routing for PPPoE Client8-52
Configuring DDR for a PPPoE Client8-53
Configuring Weighted Fair Queuing8-55
Configuring WFQ8-55
Example Configuration8-56
Configuring DSL Commands8-57...

xxi
Cisco 800 Series Software Configuration Guide
78-5372-06
Contents
ADSL Troubleshooting9-2
ADSL Cable Requirements9-2
G.SHDSL Troubleshooting9-3
show dsl interface Command9-3
ATM Troubleshooting Commands9-6
ping atm interface Command9-6
show interface Command9-7
debug atm Commands9-10
Before Using Debug Commands9-10
debug atm errors Command9-11
debug atm events Command9-12
debug atm packet Command9-13
Troubleshooting Telephone Interfaces9-15
Troubleshooting Serial Line Problems9-16
Synchronous CSU/DSU...

Contents
xxii
Cisco 800 Series Software Configuration Guide
78-5372-06
Modem Cannot Send or Receive Data9-37
Modem Cannot Send or Receive IP Data9-39
Modem Does Not Disconnect Properly9-41
Link Deactivates Too Quickly9-42
Link Does Not Deactivate or Stays Activated Too Long9-42
Poor Dial-Up Connection Performance9-43
Frame Relay Problems9-45
Frame Relay Link Is Down9-45
Cannot Ping Remote Router9-48
Cannot Ping End to End9-51
X.25 Problems9-51
No Connections over X.25 Link9-52
Excess Serial Errors on...

xxiii
Cisco 800 Series Software Configuration Guide
78-5372-06
Contents
Undoing CommandsA-9
Command-Line Error MessagesA-9
Saving Configuration ChangesA-10
Partition and SqueezeA-11
SummaryA-12
Where to Go NextA-13
ROM MonitorB-1
Entering the ROM MonitorB-2
Who Should Upgrade ROMMON and WhyB-3
Where to Find New Versions of ROMMONB-3
Performing the UpgradeB-3
Updating in Cisco IOS EXEC ModeB-5
ROM Monitor CommandsB-5
Command DescriptionsB-6
Disaster Recovery with TFTP DownloadB-7
tftpdnld Command...

Contents
xxiv
Cisco 800 Series Software Configuration Guide
78-5372-06
Command DescriptionB-16
Error ReportingB-17
Debug CommandsB-18
Exiting the ROM MonitorB-19
Common Port AssignmentsC-1
Provisioning an ISDN LineD-1
Before Ordering an ISDN LineD-1
Data and Voice ApplicationsD-2
Data and Voice Application FeaturesD-2
ISDN Switch TypesD-4
North American ISDN SwitchesD-4
International SwitchesD-5
NI1 Capability Packages and National ISDN Ordering CodesD-5
Capability Package RD-6
Capability Package SD-6...

xxv
Cisco 800 Series Software Configuration Guide
78-5372-06
Contents
Configure a Router and One DeviceD-15
Configuration Requirements for Switches Outside North AmericaD-15
1TR6 SwitchD-16
ISDN BRI Cause ValuesE-1
INDEX 

Contents
xxvi
Cisco 800 Series Software Configuration Guide
78-5372-06 

 
xxvii
Cisco 800 Series Software Configuration Guide
78-5372-06
About This Guide
This preface describes the audience for, organization of, and conventions used in 
this guide. It also provides information on how to access this guide and other 
Cisco documentation on the Documentation CD-ROM that ships with Cisco 
routers and is available on the World Wide Web. 
This document provides software configuration information for the following 
Cisco routers:
•Cisco 801, 802, 803, 804, 811, and 813 ISDN...

 
About This Guide
xxviii
Cisco 800 Series Software Configuration Guide
78-5372-06
Audience
This guide is intended for network administrators whose backgrounds vary from 
having no or little experience configuring routers to having a high level of 
experience. You can use this guide in the following ways:
You have configured the software using the Cisco Router Web Setup tool, 
and want to configure additional advanced software features using the 
command-line interface (CLI).
You want to configure the...