Cisco Prime Nerk 43 User Guide

  
19-17
Cisco Prime Network 4.3.2 User Guide
Chapter 19      Managing Ethernet Networks Using Operations, Administration, and Maintenance Tools
  Configuring CFM
Command Description
Maintenance Domain> 
Configure CFM Maintenance 
DomainA maintenance domain is a management space for the purpose of 
managing and administering a network. A single entity owns and 
operates a domain and is defined by the set of ports internal to it and 
at its boundary. Each maintenance domain can contain any number 
of...

  
19-18
Cisco Prime Network 4.3.2 User Guide
Chapter 19      Managing Ethernet Networks Using Operations, Administration, and Maintenance Tools
  Configuring E-LMI
Configuring E-LMI
The following E-LMI commands can be launched from the inventory by right-clicking an E-LMI node 
and choosing Commands > Configuration. Your permissions determine whether you can run these 
commands (see Permissions for Using Ethernet OAM Tools, page B-17). To find out if a device supports 
these commands, see the Cisco...

  
19-19
Cisco Prime Network 4.3.2 User Guide
Chapter 19      Managing Ethernet Networks Using Operations, Administration, and Maintenance Tools
  Configuring L-OAM
Command Description
Assign Template on InterfaceAssign template name
Configure MultiPoint To MultiPoint 
or Point To Point EVCConfigure OAM (L-OAM) on any full-duplex 
point-to-point or emulated point-to-point Ethernet link.
Enable OAM on Interface
Disable OAM on InterfaceEnable or disable OAM on the specified interface.
Enable E-LMI On...

  
19-20
Cisco Prime Network 4.3.2 User Guide
Chapter 19      Managing Ethernet Networks Using Operations, Administration, and Maintenance Tools
  Configuring L-OAM 

CH A P T E R
  
20-1
Cisco Prime Network 4.3.2 User Guide
EDCS-1524415
20
Monitoring Carrier Grade NAT Configurations
Carrier Grade NAT is a large-scale Network Address Translation (NAT) that provides translation of 
millions of private IPv4 addresses to public IPv4 addresses. These translations support subscribers and 
content providers with a bandwidth throughput of at least 10 Gbps full-duplex. 
Carrier Grade NAT addresses the IPv4 address completion problem. It employs Network Address and 
Port...

  
20-2
Cisco Prime Network 4.3.2 User Guide
EDCS-1524415
Chapter 20      Monitoring Carrier Grade NAT Configurations
  Viewing Carrier Grade NAT Properties in Logical Inventory
Viewing Carrier Grade NAT Properties in Logical Inventory
To view Carrier Grade NAT properties in logical inventory: 
Step 1In the Vision client, double-click the Cisco CRS device configured for Carrier Grade NAT.
Step 2In the Inventory window, click Logical Inventory > Carrier Grade NAT. 
The Carrier Grade NAT properties are...

  
20-3
Cisco Prime Network 4.3.2 User Guide
EDCS-1524415
Chapter 20      Monitoring Carrier Grade NAT Configurations
  Viewing Carrier Grade NAT Properties in Logical Inventory
Table 20-1 Carrier Grade NAT Properties in Logical Inventory
Field Description
CGN Name Name of the Carrier Grade NAT service.
Preferred Location Tab
Preferred Location Hyperlinked entry to the card in physical inventory.
Preferred Location (alias) Location of module in clear text.
Location Type Configured type of location:...

  
20-4
Cisco Prime Network 4.3.2 User Guide
EDCS-1524415
Chapter 20      Monitoring Carrier Grade NAT Configurations
  Viewing Carrier Grade NAT Properties in Physical Inventory
You can also display pool utilization by right-clicking a VNE and choosing Commands > Show > Pool 
Utilization.
Viewing Carrier Grade NAT Properties in Physical Inventory
To view Carrier Grade NAT properties in physical inventory (in this example, a Cisco CRS device): 
Step 1In the Vision client, double-click the Cisco CRS...

  
20-5
Cisco Prime Network 4.3.2 User Guide
EDCS-1524415
Chapter 20      Monitoring Carrier Grade NAT Configurations
  Configuring a CG NAT Service
Figure 20-2 Carrier Grade NAT Properties in Physical Inventory 
The field CGN Service is displayed, and the entry is hyperlinked to the associated Carrier Grade NAT 
service in logical inventory. 
Configuring a CG NAT Service
The following CG NAT commands can be launched from the inventory by right-clicking the appropriate 
node and choosing Commands >...

  
20-6
Cisco Prime Network 4.3.2 User Guide
EDCS-1524415
Chapter 20      Monitoring Carrier Grade NAT Configurations
  Configuring a CG NAT Service