Cisco Asdm 7 User Guide
Have a look at the manual Cisco Asdm 7 User Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 53 Cisco manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
14-3 Cisco ASA Series Firewall ASDM Configuration Guide Chapter 14 Configuring Inspection for Management Application Protocols DCERPC Inspection DCERPC inspect maps inspect for native TCP communication between the EPM and client on well known TCP port 135. Map and lookup operations of the EPM are supported for clients. Client and server can be located in any security zone. The embedded server IP address and Port number are received from the applicable EPM response messages. Because a client may attempt multiple connections to the server port returned by EPM, multiple use of pinholes are allowed, which have user configurable timeouts. Fields DCERPC Inspect Maps—Table that lists the defined DCERPC inspect maps. Add—Configures a new DCERPC inspect map. To edit a DCERPC inspect map, choose the DCERPC entry in the DCERPC Inspect Maps table and click Customize. Delete—Deletes the inspect map selected in the DCERPC Inspect Maps table. Security Level—Select the security level (high, medium, or low). –Low Pinhole timeout: 00:02:00 Endpoint mapper service: not enforced Endpoint mapper service lookup: enabled Endpoint mapper service lookup timeout: 00:05:00 –Medium—Default. Pinhole timeout: 00:01:00 Endpoint mapper service: not enforced Endpoint mapper service lookup: disabled. –High Pinhole timeout: 00:01:00 Endpoint mapper service: enforced Endpoint mapper service lookup: disabled –Customize—Opens the Add/Edit DCERPC Policy Map dialog box for additional settings. –Default Level—Sets the security level back to the default level of Medium. Add/Edit DCERPC Policy Map Configuration > Global Objects > Inspect Maps > DCERPC > DCERPC Inspect Map > Basic/Advanced View The Add/Edit DCERPC Policy Map pane lets you configure the security level and parameters for DCERPC application inspection maps. Fields Name—When adding a DCERPC map, enter the name of the DCERPC map. When editing a DCERPC map, the name of the previously configured DCERPC map is shown. Description—Enter the description of the DCERPC map, up to 200 characters in length. Security Level—Select the security level (high, medium, or low). –Low Pinhole timeout: 00:02:00
14-4 Cisco ASA Series Firewall ASDM Configuration Guide Chapter 14 Configuring Inspection for Management Application Protocols GTP Inspection Endpoint mapper service: not enforced Endpoint mapper service lookup: enabled Endpoint mapper service lookup timeout: 00:05:00 –Medium—Default. Pinhole timeout: 00:01:00 Endpoint mapper service: not enforced Endpoint mapper service lookup: disabled. –High Pinhole timeout: 00:01:00 Endpoint mapper service: enforced Endpoint mapper service lookup: disabled –Default Level—Sets the security level back to the default level of Medium. Details—Shows the Parameters to configure additional settings. –Pinhole Timeout—Sets the pinhole timeout. Because a client may use the server information returned by the endpoint mapper for multiple connections, the timeout value is configurable based on the client application environment. Range is from 0:0:1 to 1193:0:0. Default is 2 minutes. –Enforce endpoint-mapper service—Enforces endpoint mapper service during binding. –Enable endpoint-mapper service lookup—Enables the lookup operation of the endpoint mapper service. If disabled, the pinhole timeout is used. Enforce Service Lookup Timeout—Enforces the service lookup timeout specified. Service Lookup Timeout—Sets the timeout for pinholes from lookup operation. GTP Inspection This section describes the GTP inspection engine. This section includes the following topics: GTP Inspection Overview, page 14-5 “Select GTP Map” section on page 14-5 “GTP Inspect Map” section on page 14-6 “IMSI Prefix Filtering” section on page 14-7 “Add/Edit GTP Policy Map (Security Level)” section on page 14-7 “Add/Edit GTP Policy Map (Details)” section on page 14-8 “Add/Edit GTP Map” section on page 14-9 NoteGTP inspection requires a special license.
14-5 Cisco ASA Series Firewall ASDM Configuration Guide Chapter 14 Configuring Inspection for Management Application Protocols GTP Inspection GTP Inspection Overview GPRS provides uninterrupted connectivity for mobile subscribers between GSM networks and corporate networks or the Internet. The GGSN is the interface between the GPRS wireless data network and other networks. The SGSN performs mobility, data session management, and data compression (See Figure 14-1). Figure 14-1 GPRS Tunneling Protocol The UMTS is the commercial convergence of fixed-line telephony, mobile, Internet and computer technology. UTRAN is the networking protocol used for implementing wireless networks in this system. GTP allows multi-protocol packets to be tunneled through a UMTS/GPRS backbone between a GGSN, an SGSN and the UTRAN. GTP does not include any inherent security or encryption of user data, but using GTP with the ASA helps protect your network against these risks. The SGSN is logically connected to a GGSN using GTP. GTP allows multiprotocol packets to be tunneled through the GPRS backbone between GSNs. GTP provides a tunnel control and management protocol that allows the SGSN to provide GPRS network access for a mobile station by creating, modifying, and deleting tunnels. GTP uses a tunneling mechanism to provide a service for carrying user data packets. NoteWhen using GTP with failover, if a GTP connection is established and the active unit fails before data is transmitted over the tunnel, the GTP data connection (with a “j” flag set) is not replicated to the standby unit. This occurs because the active unit does not replicate embryonic connections to the standby unit. Select GTP Map Add/Edit Service Policy Rule Wizard > Rule Actions > Protocol Inspection Tab >Select GTP Map 119935 Internet Corporate network 2 Corporate network 1 Home PLMN Gn Gp GRX Roaming partner (visited PLMN) MS SGSNGGSNGi
14-6 Cisco ASA Series Firewall ASDM Configuration Guide Chapter 14 Configuring Inspection for Management Application Protocols GTP Inspection The Select GTP Map dialog box lets you select or create a new GTP map. A GTP map lets you change the configuration values used for GTP application inspection. The Select GTP Map table provides a list of previously configured maps that you can select for application inspection. NoteGTP inspection requires a special license. If you try to enable GTP application inspection on a ASA without the required license, the ASA displays an error message. Fields Use the default GTP inspection map—Specifies to use the default GTP map. Select an GTP map for fine control over inspection—Lets you select a defined application inspection map or add a new one. Add—Opens the Add Policy Map dialog box for the inspection. GTP Inspect Map Configuration > Global Objects > Inspect Maps > GTP The GTP pane lets you view previously configured GTP application inspection maps. A GTP map lets you change the default configuration values used for GTP application inspection. GTP is a relatively new protocol designed to provide security for wireless connections to TCP/IP networks, such as the Internet. You can use a GTP map to control timeout values, message sizes, tunnel counts, and GTP versions traversing the security appliance. NoteGTP inspection is not available without a special license. Fields GTP Inspect Maps—Table that lists the defined GTP inspect maps. Add—Configures a new GTP inspect map. To edit a GTP inspect map, choose the GTP entry in the GTP Inspect Maps table and click Customize. Delete—Deletes the inspect map selected in the GTP Inspect Maps table. Security Level—Security level low only. –Do not Permit Errors –Maximum Number of Tunnels: 500 –GSN timeout: 00:30:00 –Pdp-Context timeout: 00:30:00 –Request timeout: 00:01:00 –Signaling timeout: 00:30:00. –Tunnel timeout: 01:00:00. –T3-response timeout: 00:00:20. –Drop and log unknown message IDs. IMSI Prefix Filtering—Opens the IMSI Prefix Filtering dialog box to configure IMSI prefix filters. Customize—Opens the Add/Edit GTP Policy Map dialog box for additional settings.
14-7 Cisco ASA Series Firewall ASDM Configuration Guide Chapter 14 Configuring Inspection for Management Application Protocols GTP Inspection Default Level—Sets the security level back to the default. IMSI Prefix Filtering Configuration > Global Objects > Inspect Maps > GTP > IMSI Prefix Filtering The IMSI Prefix tab lets you define the IMSI prefix to allow within GTP requests. Fields Mobile Country Code—Defines the non-zero, three-digit value identifying the mobile country code. One or two-digit entries will be prepended by 0 to create a three-digit value. Mobile Network Code—Defines the two or three-digit value identifying the network code. Add—Add the specified country code and network code to the IMSI Prefix table. Delete—Deletes the specified country code and network code from the IMSI Prefix table. Add/Edit GTP Policy Map (Security Level) Configuration > Global Objects > Inspect Maps > GTP > GTP Inspect Map > Basic View The Add/Edit GTP Policy Map pane lets you configure the security level and additional settings for GTP application inspection maps. Fields Name—When adding a GTP map, enter the name of the GTP map. When editing a GTP map, the name of the previously configured GTP map is shown. Description—Enter the description of the GTP map, up to 200 characters in length. Security Level—Security level low only. Do not Permit Errors Maximum Number of Tunnels: 500 GSN timeout: 00:30:00 Pdp-Context timeout: 00:30:00 Request timeout: 00:01:00 Signaling timeout: 00:30:00. Tunnel timeout: 01:00:00. T3-response timeout: 00:00:20. Drop and log unknown message IDs. –IMSI Prefix Filtering—Opens the IMSI Prefix Filtering dialog box to configure IMSI prefix filters. –Default Level—Sets the security level back to the default. Details—Shows the Parameters, IMSI Prefix Filtering, and Inspections tabs to configure additional settings.
14-8 Cisco ASA Series Firewall ASDM Configuration Guide Chapter 14 Configuring Inspection for Management Application Protocols GTP Inspection Add/Edit GTP Policy Map (Details) Configuration > Global Objects > Inspect Maps > GTP > GTP Inspect Map > Advanced View The Add/Edit GTP Policy Map pane lets you configure the security level and additional settings for GTP application inspection maps. Fields Name—When adding a GTP map, enter the name of the GTP map. When editing a GTP map, the name of the previously configured GTP map is shown. Description—Enter the description of the GTP map, up to 200 characters in length. Security Level—Shows the security level and IMSI prefix filtering settings to configure. Permit Parameters—Tab that lets you configure the permit parameters for the GTP inspect map. –Object Groups to Add From object group—Specify an object group or use the browse button to open the Add Network Object Group dialog box. To object group—Specify an object group or use the browse button to open the Add Network Object Group dialog box. –Add—Add the specified country code and network code to the IMSI Prefix table. –Delete—Deletes the specified country code and network code from the IMSI Prefix table. –Permit Errors—Lets any packets that are invalid or that encountered an error during inspection to be sent through the ASA instead of being dropped. By default, all invalid packets or packets that failed during parsing are dropped. General Parameters—Tab that lets you configure the general parameters for the GTP inspect map. –Maximum Number of Requests—Lets you change the default for the maximum request queue size allowed. The default for the maximum request queue size is 200. Specifies the maximum number of GTP requests that will be queued waiting for a response. The permitted range is from 1 to 9999999. –Maximum Number of Tunnels—Lets you change the default for the maximum number of tunnels allowed. The default tunnel limit is 500. Specifies the maximum number of tunnels allowed. The permitted range is from 1 to 9999999 for the global overall tunnel limit. –Timeouts GSN timeout—Lets you change the default for the maximum period of inactivity before a GSN is removed. The default is 30 minutes. Timeout is in the format hh:mm:ss, where hh specifies the hour, mm specifies the minutes, and ss specifies the seconds. A value 0 means never tear down. PDP-Context timeout—Lets you change the default for the maximum period of inactivity before receiving the PDP Context for a GTP session. The default is 30 minutes. Timeout is in the format hh:mm:ss, where hh specifies the hour, mm specifies the minutes, and ss specifies the seconds. A value 0 means never tear down. Request Queue—Lets you change the default for the maximum period of inactivity before receiving the GTP message during a GTP session. The default is 1 minute. Timeout is in the format hh:mm:ss, where hh specifies the hour, mm specifies the minutes, and ss specifies the seconds. A value 0 means never tear down.
14-9 Cisco ASA Series Firewall ASDM Configuration Guide Chapter 14 Configuring Inspection for Management Application Protocols GTP Inspection Signaling—Lets you change the default for the maximum period of inactivity before a GTP signaling is removed. The default is 30 minutes. Timeout is in the format hh:mm:ss, where hh specifies the hour, mm specifies the minutes, and ss specifies the seconds. A value 0 means never tear down. Tunnel—Lets you change the default for the maximum period of inactivity for the GTP tunnel. The default is 1 hour. Timeout is in the format hh:mm:ss, where hh specifies the hour, mm specifies the minutes, and ss specifies the seconds. A value 0 means never tear down Request timeout—Specifies the GTP Request idle timeout. T3-Response timeout—Specifies the maximum wait time for a response before removing the connection. IMSI Prefix Filtering—Tab that lets you configure the IMSI prefix filtering for the GTP inspect map. –Mobile Country Code—Defines the non-zero, three-digit value identifying the mobile country code. One or two-digit entries will be prepended by 0 to create a three-digit value. –Mobile Network Code—Defines the two or three-digit value identifying the network code. –Add—Add the specified country code and network code to the IMSI Prefix table. –Delete—Deletes the specified country code and network code from the IMSI Prefix table. Inspections—Tab that lets you configure the GTP inspect maps. –Match Type—Shows the match type, which can be a positive or negative match. –Criterion—Shows the criterion of the GTP inspection. –Value—Shows the value to match in the GTP inspection. –Action—Shows the action if the match condition is met. –Log—Shows the log state. –Add—Opens the Add GTP Inspect dialog box to add an GTP inspection. –Edit—Opens the Edit GTP Inspect dialog box to edit an GTP inspection. –Delete—Deletes an GTP inspection. –Move Up—Moves an inspection up in the list. –Move Down—Moves an inspection down in the list. Add/Edit GTP Map Configuration > Global Objects > Inspect Maps > GTP > GTP Inspect Map > Add/Edit GTP Map The Add/Edit GTP Inspect dialog box lets you define the match criterion and value for the GTP inspect map. Fields Match Type—Specifies whether traffic should match or not match the values. For example, if No Match is selected on the string “example.com,” then any traffic that contains “example.com” is excluded from the class map. Criterion—Specifies which criterion of GTP traffic to match. –Access Point Name—Match on access point name. –Message ID—Match on the message ID.
14-10 Cisco ASA Series Firewall ASDM Configuration Guide Chapter 14 Configuring Inspection for Management Application Protocols RADIUS Accounting Inspection –Message Length—Match on the message length –Version—Match on the version. Access Point Name Criterion Values—Specifies an access point name to be matched. By default, all messages with valid APNs are inspected, and any APN is allowed. –Regular Expression—Lists the defined regular expressions to match. –Manage—Opens the Manage Regular Expressions dialog box, which lets you configure regular expressions. –Regular Expression Class—Lists the defined regular expression classes to match. –Manage—Opens the Manage Regular Expression Class dialog box, which lets you configure regular expression class maps. –Action—Drop. –Log—Enable or disable. Message ID Criterion Values—Specifies the numeric identifier for the message that you want to match. The valid range is 1 to 255. By default, all valid message IDs are allowed. –Value—Specifies whether value is an exact match or a range. Equals—Enter a value. Range—Enter a range of values. –Action—Drop packet or limit rate (pps). –Log—Enable or disable. Message Length Criterion Values—Lets you change the default for the maximum message length for the UDP payload that is allowed. –Minimum value—Specifies the minimum number of bytes in the UDP payload. The range is from 1 to 65536. –Maximum value—Specifies the maximum number of bytes in the UDP payload. The range is from 1 to 65536. –Action—Drop packet. –Log—Enable or disable. Version Criterion Values—Specifies the GTP version for messages that you want to match. The valid range is 0-255. Use 0 to identify Version 0 and 1 to identify Version 1. Version 0 of GTP uses port 3386, while Version 1 uses port 2123. By default all GTP versions are allowed. –Value—Specifies whether value is an exact match or a range. Equals—Enter a value. Range—Enter a range of values. –Action—Drop packet. –Log—Enable or disable. RADIUS Accounting Inspection This section describes the IM inspection engine. This section includes the following topics: RADIUS Accounting Inspection Overview, page 14-11
14-11 Cisco ASA Series Firewall ASDM Configuration Guide Chapter 14 Configuring Inspection for Management Application Protocols RADIUS Accounting Inspection Select RADIUS Accounting Map, page 14-11 Add RADIUS Accounting Policy Map, page 14-11 RADIUS Inspect Map, page 14-12 RADIUS Inspect Map Host, page 14-12 RADIUS Inspect Map Other, page 14-13 RADIUS Accounting Inspection Overview One of the well known problems is the over-billing attack in GPRS networks. The over-billing attack can cause consumers anger and frustration by being billed for services that they have not used. In this case, a malicious attacker sets up a connection to a server and obtains an IP address from the SGSN. When the attacker ends the call, the malicious server will still send packets to it, which gets dropped by the GGSN, but the connection from the server remains active. The IP address assigned to the malicious attacker gets released and reassigned to a legitimate user who will then get billed for services that the attacker will use. RADIUS accounting inspection prevents this type of attack by ensuring the traffic seen by the GGSN is legitimate. With the RADIUS accounting feature properly configured, the security appliance tears down a connection based on matching the Framed IP attribute in the Radius Accounting Request Start message with the Radius Accounting Request Stop message. When the Stop message is seen with the matching IP address in the Framed IP attribute, the security appliance looks for all connections with the source matching the IP address. You have the option to configure a secret pre-shared key with the RADIUS server so the security appliance can validate the message. If the shared secret is not configured, the security appliance does not need to validate the source of the message and will only check that the source IP address is one of the configured addresses allowed to send the RADIUS messages. NoteWhen using RADIUS accounting inspection with GPRS enabled, theASA checks for the 3GPP-Session-Stop-Indicator in the Accounting Request STOP messages to properly handle secondary PDP contexts. Specifically, the ASA requires that the Accounting Request STOP messages include the 3GPP-SGSN-Address attribute before it will temrinate the user sessions and all associated connections. Some third-party GGSNs might not send this attribute by default. Select RADIUS Accounting Map The Select RADIUS Accounting Map dialog box lets you select a defined RADIUS accounting map or define a new one. Fields Add—Lets you add a new RADIUS accounting map. Add RADIUS Accounting Policy Map The Add RADIUS Accounting Policy Map dialog box lets you add the basic settings for the RADIUS accounting map.
14-12 Cisco ASA Series Firewall ASDM Configuration Guide Chapter 14 Configuring Inspection for Management Application Protocols RADIUS Accounting Inspection Fields Name—Enter the name of the previously configured RADIUS accounting map. Description—Enter the description of the RADIUS accounting map, up to 100 characters in length. Host Parameters tab: –Host IP Address—Specify the IP address of the host that is sending the RADIUS messages. –Key: (optional)—Specify the key. –Add—Adds the host entry to the Host table. –Delete—Deletes the host entry from the Host table. Other Parameters tab: –Attribute Number—Specify the attribute number to validate when an Accounting Start is received. –Add—Adds the entry to the Attribute table. –Delete—Deletes the entry from the Attribute table. –Send response to the originator of the RADIUS message—Sends a message back to the host from which the RADIUS message was sent. –Enforce timeout—Enables the timeout for users. Users Timeout—Timeout for the users in the database (hh:mm:ss). RADIUS Inspect Map The RADIUS pane lets you view previously configured RADIUS application inspection maps. A RADIUS map lets you change the default configuration values used for RADIUS application inspection. You can use a RADIUS map to protect against an overbilling attack. Fields Name—Enter the name of the inspect map, up to 40 characters in length. Description—Enter the description of the inspect map, up to 200 characters in length. RADIUS Inspect Maps—Table that lists the defined RADIUS inspect maps. The defined inspect maps are also listed in the RADIUS area of the Inspect Maps tree. Add—Adds the new RADIUS inspect map to the defined list in the RADIUS Inspect Maps table and to the RADIUS area of the Inspect Maps tree. To configure the new RADIUS map, select the RADIUS entry in Inspect Maps tree. Delete—Deletes the application inspection map selected in the RADIUS Inspect Maps table and from the RADIUS area of the Inspect Maps tree. RADIUS Inspect Map Host The RADIUS Inspect Map Host Parameters pane lets you configure the host parameter settings for the inspect map.