Cisco 6500e Manual

1-69
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Chapter 1      Product Overview
  Catalyst 6513-E Switch
Ta b l e 1 - 2 3 lists the features of the Catalyst 6513-E switch chassis. 
Table 1-23 Catalyst 6513-E Switch Features
Feature Description
Chassis
Thirteen horizontal slots. Slots are numbered from (1) top to (13) 
bottom. 
Supervisor engines
Supports Supervisor Engine 32, Supervisor Engine 720, Supervisor 
Engine 720-10GE, and Supervisor Engine 2T. 
NoteRefer to your software release...

1-70
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Chapter 1      Product Overview
  Catalyst 6513-E Switch
Clock and VTT moduleTwo clock modules provide clocking signals to the EOBC channel and 
the switching bus.
Three voltage termination (VTT) modules provide reference voltage for 
bus signals.
Fan tray
The chassis supports one hot-swappable fan tray. One fan tray model is 
available:
–WS-C6513-E-FAN(=)—1755 CFM
NoteThe fan tray contains 15 individual fans. The individual fans are not...

1-71
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Chapter 1      Product Overview
  Catalyst 6513-E Switch
Power supplySupports one or two power supplies. The following models are 
supported:
–WS-CDC-2500W (2500 W DC-input power supply).
–WS-CAC-3000W (3000 W AC-input power supply).
–WS-CAC-4000W-US (4000 W AC-input power supply).
–WS-CAC-4000W-INT (4000 W AC-input power supply).
–PWR-4000-DC (4000 W DC-input power supply).
–WS-CAC-6000W (6000 W AC-input power supply).
–PWR-6000-DC (6000 W...

1-72
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Chapter 1      Product Overview
  Catalyst 6513-E Switch
Ta b l e 1 - 2 4 lists the environmental and physical specifications of the Catalyst 6513-E switch chassis.
Table 1-24 Catalyst 6513-E Switch Specifications
Item Specification
Environmental
Temperature, operating Certified for operation: 32° to 104°F (0° to 40°C)
Designed and tested for operation: 32° to 131°F (0° to 55°C)
NoteThe Catalyst 6500 series switches are equipped with...

1-73
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Chapter 1      Product Overview
  Catalyst 6513-E Switch
Physical characteristics
Dimensions (H x W x D)
33.3 x 17.3 x 18.1 in. (84.6 x 43.9 x 46.0 cm). 
Chassis requires 20 RU1.
The Catalyst 6513-E switch chassis is designed to install in standard 
19-inch equipment racks that meet ANSI/EIA 310-D, IEC 60297, and 
ETS 300-119 standards.
Weight Chassis fully configured with 2 supervisor engines, 11 switching modules, 
and 2 power supplies:...

1-74
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Chapter 1      Product Overview
  Catalyst 6513-E Switch 

CH A P T E R
1-1
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
1
Preparing for Installation
NoteIn this publication, the term Catalyst 6500 series refers only to the switch chassis listed in Chapter 1. 
The Catalyst 6000 series switches (Catalyst 6006 and Catalyst 6009 switches) are described in a 
separate publication, the Catalyst 6000 Series Switch Installation Guide.
Planning a proper location for the switch and the layout of your equipment rack or wiring closet is 
essential for...

1-2
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Chapter 1      Preparing for Installation
  Safety
Safety
Safety warnings appear throughout this publication in procedures that may harm you if performed 
incorrectly. A warning symbol precedes each warning statement. The warnings below are general 
warnings that are applicable to the entire publication.
WarningOnly trained and qualified personnel should be allowed to install, replace, or service this equipment. 
Statement 1030
WarningThis...

1-3
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Chapter 1      Preparing for Installation
  Site Requirements
Temperature
Temperature extremes can cause a system to operate at reduced efficiency and cause a variety of 
problems, including premature aging and failure of chips, and failure of mechanical devices. Extreme 
temperature fluctuations can cause chips to become loose in their sockets. Observe the following 
guidelines:
Ensure that the system is operating in an environment no...

1-4
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Chapter 1      Preparing for Installation
  Site Requirements
If you are installing your Catalyst 6500 series switch in an enclosed or partially enclosed rack, we 
strongly recommend that you verify that your site meets the following guidelines:
Verify that there is a minimum of 6 inches (15 cm) of clearance between the sides of the rack and 
both the chassis air intake grill and the chassis air exhaust grill.
Verify that the ambient air...