Cisco 1812j Manual

 
4-9
Cisco 1800 Series Integrated Services Routers (Fixed) Hardware Installation Guide
OL-6425-03
Chapter 4      Power, Cable, and Antenna Connection Procedures
  Connecting the Radio Antennas to the Wireless Router
Figure 4-2 Dipole Antenna Orientation
127911 

 
4-10
Cisco 1800 Series Integrated Services Routers (Fixed) Hardware Installation Guide
OL-6425-03
Chapter 4      Power, Cable, and Antenna Connection Procedures
  Connecting the Radio Antennas to the Wireless Router 

CH A P T E R
 
5-1
Cisco 1800 Series Integrated Services Routers (Fixed) Hardware Installation Guide
OL-6425-03
5
Power-Up and Initial Configuration Procedures
This chapter describes how to power up your Cisco 1800 series fixed-configuration router and perform 
an initial configuration for network access. This chapter includes the following sections:
 Powering Up Cisco 1800 Series Fixed-Configuration Routers, page 5-1
 Configuring the Router, page 5-3
Powering Up Cisco 1800 Series Fixed-Configuration...

 
5-2
Cisco 1800 Series Integrated Services Routers (Fixed) Hardware Installation Guide
OL-6425-03
Chapter 5      Power-Up and Initial Configuration Procedures
  Powering Up Cisco 1800 Series Fixed-Configuration Routers
Power-Up Procedure
To power up your Cisco router and verify that it completes initialization and self-test, follow the 
procedure below. After you complete this procedure, you can configure the router.
If you encounter problems when you power on the router, see the “Troubleshooting”...

 
5-3
Cisco 1800 Series Integrated Services Routers (Fixed) Hardware Installation Guide
OL-6425-03
Chapter 5      Power-Up and Initial Configuration Procedures
  Configuring the Router
To use the CLI to configure the router, see the “Initial Configuration Using the Cisco CLI—Manual 
Configuration” section on page 5-7.
NoteIf the rommon 1> prompt appears, your system has booted in ROM monitor mode.
Verifying the Front Panel LED Indications
The front-panel indicator LEDs described in Ta b l e 5-1 provide...

 
5-4
Cisco 1800 Series Integrated Services Routers (Fixed) Hardware Installation Guide
OL-6425-03
Chapter 5      Power-Up and Initial Configuration Procedures
  Configuring the Router
 Completing the Configuration
You can configure your router by using one of the following tools:
 Cisco Router and Security Device Manager—See the “Initial Configuration Using Cisco Router and 
Security Device Manager” section on page 5-4.
 Setup command facility—See the “Initial Configuration Using the Setup Command...

 
5-5
Cisco 1800 Series Integrated Services Routers (Fixed) Hardware Installation Guide
OL-6425-03
Chapter 5      Power-Up and Initial Configuration Procedures
  Configuring the Router
The setup command facility prompts you for basic information about your router and network, and it 
creates an initial configuration file. After the configuration file has been created, you can use the CLI or 
SDM to perform additional configuration. 
The prompts in the setup command facility vary, depending on your router...

 
5-6
Cisco 1800 Series Integrated Services Routers (Fixed) Hardware Installation Guide
OL-6425-03
Chapter 5      Power-Up and Initial Configuration Procedures
  Configuring the Router
A summary of the available interfaces appears.
Current interface summary
Any interface listed with OK? value NO does not have a valid configuration
Interface                  IP-Address      OK? Method Status                ProtocolAsync1                     unassigned      YES unset  down...

 
5-7
Cisco 1800 Series Integrated Services Routers (Fixed) Hardware Installation Guide
OL-6425-03
Chapter 5      Power-Up and Initial Configuration Procedures
  Configuring the Router
shutdown
no ip address!interface FastEthernet4
shutdownno ip address!
interface FastEthernet5shutdownno ip address
!interface FastEthernet6shutdown
no ip address!interface FastEthernet7
shutdownno ip address!
interface FastEthernet8shutdownno ip address
!interface FastEthernet9shutdown
no ip address!interface Vlan1...

 
5-8
Cisco 1800 Series Integrated Services Routers (Fixed) Hardware Installation Guide
OL-6425-03
Chapter 5      Power-Up and Initial Configuration Procedures
  Configuring the Router
At any point you may enter a question mark ? for help.Use ctrl-c to abort configuration dialog at any prompt.Default settings are in square brackets [].
Would you like to enter the initial configuration dialog? [yes/no]:
If these messages do not appear, then the Cisco SDM software and a default configuration file were...