Cine Versum Cineversum Blackwing User Manual

							4.0  FEATURES AND CONNECTIONS
R599727 - BlackWing User Manual21 
CAUTION AGAINST FIRE AND ELECTRIC SHOCK
Since the power consumption of this unit is high, insert the power plug directly into a wall outlet.
When not using devices, remove the power plug from the wall outlet.
Do not use power cords for connection other than specified.
Do not use a power voltage different from that which is indicated.
Do not cut, tear or modify the power cords. Also, do not place a heavy object on, heat or stretch the power cords as
this may cause damage to the cords.
Do not insert or pull plugs with a wet hand. 
						

							5.0  BASIC OPERATIONS PROCEDURES
22R599727 - BlackWing User Manual
5.0 BASIC OPERATIONS PROCEDURES
5.1 First Startup
If setting for this unit is not completed, please refer to “ADJUSTMENTS AND SETTINGS”,  page 24 upon turning on
the power and perform the required setting accordingly. Once the basic setting is completed, this unit can be used
by simply performing the following operation procedures.
Removing the lens cap
Upon using, mount the lens cap to prevent soiling of the lens.
Turning on the power
•Insert the power plug to the power outlet
The main power turns on and the [STAND BY] indicator on the unit lights up.
•Press the [OPERATE ON] button for 1 second or more
The [OPERATE] indicator on this unit lights up and the projected image slowly appears.
Adjusting zoom (screen size)
•To enlarge the screen size, press the [ZOOM T] button
•To reduce the screen size, press the [ZOOM W] button
Adjusting focus
•To focus on nearer points, press the [FOCUS +] button
•To focus on farther points, press the [FOCUS -] button
Hiding the image temporarily
•Press the [HIDE] button.The displayed image will disappear.
NOTES:
 Upon projection, the image may flicker for a few seconds. This is not a malfunction.
When the light source is turned on, the lamp will slowly become brighter. It will take more than 1 minute for the
brightness to stabilize.
NOTES:
To adjust zoom and focus, set Zoom/Focus in the Options menu to Unlock (default setting Unlock).
When this is set to Lock, a not available message will be displayed upon pressing the [ZOOM T/W] or [FOCUS +/-]
button, indicating that the operation is disabled.
STAND BY
OPERATE
LAMP
TEMP
FA N
HIDE
light ON
STAND BY
OPERATE
LAMP
TEMP
FA N
HIDElight ON 
						

							5.0  BASIC OPERATIONS PROCEDURES
R599727 - BlackWing User Manual23 
•Press the [HIDE] button again the restore the image.
Turning off the power
•Press the [OPERATE OFF] button for 1 second or more
The [OPERATE] indicator turns off, the [STAND BY] indicator starts blinking and this unit switches to the cool down
mode. The cool down mode will last for about 60 seconds to allow the temperature of the light source to cool off.
This unit switches to the standby mode at the end of the cool down mode.
•You can pull out the power plug from the power outlet
The [OPERATE OFF] button will not work within approximately 1 minute after the light source has been
turned on. Start operation only after 1 minute’s time.
Do not pull out the plug when the [STAND BY] indicator is blinking. This may shorten the lamp life and
cause a malfunction.
PRECAUTIONS DURING USE
This unit makes use of a light source lamp that may reach a high temperature during projection. Do not allow projec-
tion under the following conditions. Doing so may cause fire or malfunction of the unit.
•Projection with the unit laid on its sides
•Projection with the unit installed in an unreasonable angle
•Avoid using this unit at an inclined angle. Doing so may cause unevenness in the color or shorten the lamp
life.
•Projection at a location that blocks the air inlets or exhaust vents
•Projection without removing the lens cap
STAND BY
OPERATE
LAMP
TEMP
FA N
HIDElight ON
light ON
STAND BY
OPERATE
LAMP
TEMP
FA N
HIDE
Blinking
OFF 
						

							6.0  ADJUSTMENTS AND SETTINGS
24R599727 - BlackWing User Manual
6.0 ADJUSTMENTS AND SETTINGS
The menus displayed on the screen are used to perform adjustment and setting for this unit.
6.1 How to start up the menus
Box like menu structure
The menu structure is built up with boxes which allow easy access to different parameters for setting up the projec-
tor. A menu box item can generate an adjustment box on the right of the main menu.
How to activate the menu structure
•Press the [MENU] on the RCU or Digital Control Panel located at the rear side of the projector.
•The main menu will be displayed.
How to select an item and make an adjustment
•Use the [UP] or [DOWN] keys to highlight the desired Menu
•Press [ENTER] to select
If the selected item has adjustment values, use the [LEFT] and [RIGHT] to change the value.
If the selected item has a sub menu, this sub menu will open. (Test Pattern, Pixel Adjust)
•Use the [EXIT] key to return to the previous menu, or to clear the menu screen when the main menu is dis-
played.
Image Adjust
Setup
Options
InformationGreen
Blue Red
GammaNormalACustomBColorTemp.
TestPatternUser2User1 D65
ENTERPixelAdjustENTER
WFOCUS
CHP LIGHT TEST
MENU EXIT
PRESET HIDEON OFF
OPERATE
ENTER
ZOOM FOCUST
W
T W
ZOOM+
-
FOCUS
MENU EXIT
OPERATE
OFF
HIDE RS232C Rx
TxOPERATE
ON
Remote ControlDigital Control Panel Navigation Keys 
						

							6.0  ADJUSTMENTS AND SETTINGS
R599727 - BlackWing User Manual25 
6.2 Menu Structure
6.3 Menu Configuration
Image Adjust Menu
•To adjust images.
a) Gamma
Switches the gradation characteristics of the image. Select your preference setting values according to the image to
be viewed.
b) Color Temp.
MAIN MENUSUBMENUAVAILABLE VALUES
Image Adjust MenuGamma Normal, A, B, Custom
Color Temp.D65, User1, User2
Test Pattern10 available test patterns *
Pixel AdjustH pixel adjust, V Pixel adjust
Setup MenuMenu Position9 available positions
Mask2.5%, 5%, Off
Flip HOn, Off
Flip VOn, Off
Picture Shift-30 to 30
Options MenuMenu Display15 sec, Off
Sleep Time15min, 30 min, 60 min, Off
RS 232C(bps)9600, 19200
Zoom/FocusLock, Unlock
Power SaveOn, Off
Information MenuSource & Lamp timeShows the Source and the Lamp time.
 * TEST PATTERN MENU
Press the [ENTER] button to switch to the test pattern image. Press the [ENTER] or [TEST] button to alter the test
pattern to be projected. Press the [EXIT] button to clear the menu screen. Press the [EXIT] button again to clear the
test pattern.
Setting Values:  Normal,A,B,Custom.
Default Value:  Normal
Setting to Custom enables you to set (adjust) to a gamma value of your preference via the computer that is
connected to the projector by using a Gamma adjustment software. (Default picture quality is equivalent to
Normal). Ask your dealer for the Gamma adjustment software or contact us at www.cineversum.com. 
						

							6.0  ADJUSTMENTS AND SETTINGS
26R599727 - BlackWing User Manual
Adjusts the color temperature of the projected image.
c) Red,Green,Blue
When you set the Color Temp. setting to User1 or User2, adjustment of Red,Green,Blue can be done.
d) Test Pattern
Use this to adjust focus, screen size or picture quality. There are 10 types of test patterns. Press the [ENTER] or
[TEST] button to alter the test pattern to be projected.
Press the [EXIT] button twice to clear the test pattern.
e) Pixel Adjust
Fine-tunes the image position in the horizontal/vertical directions.
This is not required under normal circumstances.
•H Pixel Adjust
Red,Green,Blue
•V Pixel Adjust
Red,Green,Blue
Setup Menu
a) Menu Position
Adjusts the display position of the menu screen.
b) Mask
Masks (Hides) the outer area of the projected image.
c) Flip H
Reverses image to the left or right.
d) Flip V
Setting Values:  D65,User1,User2
Default Value:  D65
Setting Values: -255 to 0
Default Value:  0
Setting Values: 1 to 7
Default Value:  4
Setting Values: 1 to 7
Default Value:  4
H/V Pixel Adjust allows fine-tuning of images in the horizontal/vertical directions up to ±3 pixels at intervals
of 1 pixel for each of Red, Green and Blue. Make use of a still image with a clear outline during adjustment.
This feature is intended for fine-tuning of images and therefore the effect upon adjustment may not be visible to the
eye.
Setting 
Values:
Default Value:
Setting Values:  2.5%,5%,Off
Default Value:  Off
Setting Values:  On,Off
Default Value:  Off 
						

							6.0  ADJUSTMENTS AND SETTINGS
R599727 - BlackWing User Manual27 
Inverts image upside down.
e) Picture Shift
When projecting images with black bands at the top and bottom (cinema image), use this to move the image up or
down while retaining one of the black bands at the upper or lower end.
Option Menu
a) Menu Display
Adjusts the display duration of the menu screen.
The menu screen display will not disappear automatically when this is set to On. Press the [EXIT] button to clear the
menu screen.
b) Sleep Time
Sets the lapse time before automatically switching the unit to the standby mode when there is no signal input.
c) RS232C (bps)
Sets the communication speed (signal transmission speed) when communicating with a computer using the RS-
232C terminal. Ensure that this is same as the rate set at the computer.
d) Zoom/Focus
Locks/Unlocks the power zoom/power focus functions of the projection lens.
e) Power Save
Switches the power (brightness) of the light-source lamp.
•It is possible to lower the power (brightness) of the light-source lamp when this is set to On, but the display will
appear darker than when this is set to Off.
•Adjustment of settings will be disabled for about 1 minute after the setting is changed. In this case, adjust set-
tings after a lapse of at least 1 minute.
•Altering the On,Off setting does not affect the lamp usage time (lamp life) of the light-source lamp.
Information Menu
a) Lamp Time
Displays the accumulated hours of usage of the light-source lamp.
b) Source
Automatically identifies the input video signal at the [DVI] terminal of this unit and displays the signal name
(1080p48, 1080p50 or 1080p60).
When there is no video signal input to the [DVI] terminal, or when there is input of a video signal that cannot be used
with this unit, no signal name will be displayed.
Setting Values:  On,Off
Default Value:  Off
Setting Values: -30 to 30
Default Value:  0
Setting Values:  15sec,On
Default Value:  15sec
Setting Values:  15min,30min,60min,Off
Default Value:  Off
Setting Values:  9600,19200
Default Value:  19200
Setting Values:  Lock,Unlock
Default Value:  Unlock
Setting Values:  On,Off
Default Value:  Off 
						

							6.0  ADJUSTMENTS AND SETTINGS
28R599727 - BlackWing User Manual
INPUT INFORMATION
When the input video signal is switched, a blue back image will appear for about 2 seconds.
When nothing is connected to the [DVI] terminal, or if there is no video signal, a No Signal DVI-D message will be
projected.
For a video signal that cannot be used with this unit, a Out of Range message will be projected.
Video input signals that can be used with this unit are 1080p48, 1080p50 and 1080p60 signals by DVI-D 
						

							7.0  ADVANCED SETTINGS
R599727 - BlackWing User Manual29 
7.0 ADVANCED SETTINGS
7.1 Picture Shift setting
When projecting images with black bands at the top and bottom (cinema image), use this to move the image up or
down while retaining one of the black bands at the upper or lower end. The default value is 0 (Off) and can be set
from -30 to +30.
7.2 Screen Masking
Mask adjustment affects only the edges of the projected image and are used to frame the projected image on to the
screen and to hide or black out unwanted information and noise. The masking can be set to 0% (off), 2.5% or 5%
Project the picture on the screen.
Default picture, shift value: 0. 
Press the MENU button to get the main menu on the screen.
Press up/down buttons to select SETUP, then press ENTER button.
Press Up/Down buttons to select Picture Shift, followed by pressing
the buttons Left/Right to modify the setting value.
Set value in the positive (+) direction to move the picture upwards
and negative (-) direction to move downwards.
Picture with value set to 30.
Press the MENU button to exit the OSD.The menu disappear from the
screen.
Image Adjust
Setup
Options
InformationGreen
Blue Red
GammaNormalACustomBColorTemp.
TestPatternUser2User1 D65
ENTERPixelAdjustENTER
Image Adjust
Options
InformationMenuPositionMaskOff5% 2.5%Setup
PictureShift FlipV
OnOff
On
0OffFlipH
Image Adjust
Options
InformationSetupMaskOff5% 2.5%
FlipVOnOff
OnOffFlipH
MenuPosition
PictureShift30 
						

							7.0  ADVANCED SETTINGS
30R599727 - BlackWing User Manual
7.3 Input balance
Introduction to calibration
When transporting signals, there is always a risk of deterioration of the information contained in the signals. 
During the projector installation, a proper colour calibration is required to benefit a well balanced colorimetry.
Gamma settings
The Gamma correction factor can be set to Normal (default), A , B or Custom.
Gamma is the relationship between the color values of the data and the color values displayed. The Gamma coeffi-
cient makes it possible to adjust the brightness of the midtones only without affecting the very bright and very dark
areas. If gamma is set too high, middle tones appear too dark. If it's set too low, middle tones appear too light.
A custom gamma table can be loaded by software from a computer connected to the projector through the RS-
Project the picture on the screen.
Press the MENU button to get the main menu on the screen.
Press up/down buttons to select SETUP, then press ENTER button.
Press Up/Down buttons to select Mask, followed by pressing the but-
tons Left/Right to select the setting value.
Picture with mask value of 2.5%
Press the MENU button to exit the OSD.The menu disappear from the
screen.
Image Adjust
Setup
Options
InformationGreen
Blue Red
GammaNormalACustomBColorTemp.
TestPatternUser2User1 D65
ENTERPixelAdjustENTER
Image Adjust
Options
InformationMenuPositionMaskOff5% 2.5%Setup
PictureShift FlipV
OnOff
On
0OffFlipH
Image adjust
Options
InformationSet upMaskOff5% 2.5%MenuPosition
PictureShift FlipV
OnOff
On
0OffFlipH