Christie Projector Mirage 304K User Manual

							To maintain original brightness if a lamp fails when operating fewer than six lamps, BrightSelect
automatically strik es one of the inactive lamps.

						

							Setting up projector
pro
						

							5. Select 
Restore.
Renaming a pr ojector pro
						

							Backup, restore, and
upgrade pr
ojector 

						

							Importing a 
						

							Diagnostic tools
F ollow these procedures to help with diagnosing issues with Mirage 304K.
Viewing projector information View the licenses for the software added to the projector and the licenses of the software used to
operate the projector. The information is read-only.
1. To view the additional software added to the projector, select  MENU > Licenses.
2. To view the software licenses used to runthe projector, select  MENU > About.
Viewing lamp information
Monitor the states of the lamps and the number of hours used. 1. Select  MENU > Status >  Lamp Info.
2. Use the right arrow to select the lamp list.
3. For a detailed view of a specific lamp, select  Enter.
Adding lamp end-of-life indicator
Specify the number of hours remaining before issuing an end-of-life indicator for the lamp. 1. Select  MENU > Configuration >  Lamp > Lamp Life Warning at (Hours) .
2. Select  Enter.
3. Use the right and left arrows to specify the number of hours remaining before issuing a lamp end-of-life warning.
4. To save the adjustment, select  Enter.
Freezing an image
Use the Freeze Image diagnostic tool to examine in detail a still version of an incoming image.
For example, in moving images sometimes it is difficult to observe artifacts such as external de-
interlacing/resizing and signal noise. 1. Select  MENU > Admin  > Diagnostics.
2. To enable freezing of an image, select  Freeze Image and select Enter.
3. To return to normal operation, select  Enter again to clear the checkbox.  
Mirage 304K (Bm.1) User Manual
36
020-101778-04 R
 ev. 1 (07-2016)
Copyright  
						

							Test patterns
Use the projector  and light engine test patterns to assist with configuration of the projector and to
diagnose any issues that may occur.
Selecting a test pattern 21 test patterns are available to assist with the configuration of the projector and to diagnose any
issues that may occur.
1. From the side panel home page, use the arrows to select  Test Pattern.
You can also select the test patterns from  MENU > Test Pattern .
2. Scroll through the list of test patterns.
3. Select the required test pattern.
4. To confirm your selection, select  Enter.
Modifying grey level test pattern characteristics Set the level of grey dispalyed in the full grey test patterns. 1. Select  MENU > Admin > Diagnostics .
2. Select  Test Pattern .
3. Select one of the grey test patterns: GREY SCALE 16 or FLAT GREY.
4. Select  Enter.
5. To change the grey scale of the test pattern, select  Test Pattern Grey Level and adjust the
slider to the value you want.
6. To confirm your selection, select  Enter.
Modifying ramp test pattern characteristics
Modify the characteristics for the associated ramp video signal test patterns.
1. Select  MENU > Admin > Diagnostics .
2. Select  Test Pattern .
3. Select one of the ramp test patterns: RGBW RAMP, HORIZONTAL RAMP, VERTICAL RAMP, or DIAGONAL RAMP.
4. Select  Enter.
5. To enable mvoement of the test pattern, select  Test Pattern Ramp Motion and select
Enter.
6. To change the slope of the ramp test pattern, select  Test Pattern Ramp Slope and adjust
the slider to the value you want.
7. To confirm your selection, select  Enter.
8. To change the level of the ramp test pattern, select  Test Pattern Ramp Level and adjust
the slider to the value you want.
9. To confirm your selection, select  Enter. Diagnostic tools
Mirage 304K (Bm.1) User Manual
37
020-101778-04 R
 ev. 1 (07-2016)
Copyright  
						

							Modifying grid test pattern characteristics
Modif y the characteristics for the associated gridl test patterns.
1. Select  MENU > Admin  > Diagnostics .
2. Select  Test Pattern .
3. Select one of the grid test patterns: SQUARE GRID or DIAGONAL GRID.
4. Select  Enter.
5. To change the pitch of the grid test pattern, select  Test Pattern Grid Pitch and adjust the
slider to the value you want.
6. To confirm your selection, select  Enter.
7. To change the color of the grid, select  Test Pattern Grid Color and select Enter.
8. To enable movement of the test pattern, select  Test Pattern Grid Motion and select Enter.
Enabling a speci
						

							Successful connection includes a visual cue on the screen, haptic feedback on the device, and
an auditory cue as well.
3.
Review the projector IP address and lamp hour information provided.
Running the Mirage 304K interrogator The interrogator captures diagnostic information Christie personnel uses to help diagnose and correct
any issues. 1. Insert a USB flash drive in the USB port on Mirage 304K.If two USB flash drives are inserted, the first flash drive inserted is the one recognized. The
USB flash drive must be formatted using the FAT 32 file system.
2. From the display panel, select  MENU > Admin > Interrogator .
3. Select  Run.
The interrogator file is stored at the root directory on the USB flash drive.
4. At the completion prompt, select  OK.
Monitoring Mirage 304K with SNMP The SNMP (simple network management protocol) interface provides a common way to manage
network devices from a single remote location.
With SNMP, you can configure trap notifications to be sent when certain events occur.
Setting the SNMP read community string The SNMP read community string is similar to a userid or password that allows access to the device. 1. Select  MENU  > Communications >  SNMP > SNMP Read Community .
2. Use the up and down arrows to enter the read community string.
3. To confirm your selection, select  Enter.
Con
						

							De