Christie Projector M-Series User Manual

M-Series User Manual1-3020-100009-01 Rev.1 (07/08)
Should you encounter a problem with any part of the projector, contact your dealer. In most cases, 
servicing can be performed on site. If you have purchased the projector, fill out the information below 
and keep with your records.
Table 1.1 Purchase Record
* The serial number can be found on the rear of the projector.
Table 1.2 Ethernet Settings
1.3PROJECTOR OVERVIEW
The M-Series is a family of high resolution video/graphics 3 
chip HD and SXGA+...

Section 1: Introduction
M-Series User Manual1-4020-100009-01 Rev.1 (07/08)
• PIP and seamless switching
• LiteLOC™ for constant brightness maintenance
• Intelligent Lens System (ILS) 
• Motorized lens mount for all models
• Auto-setup feature
• Integrated ChristieNET 
• Networking ability through RS232 and RS422 connectors
• Status LED display on built-in keypad for easy projector status monitoring
• Control with remote keypad, wired remote, or built-in keypad
• Four input slots for Optional Input...

M-Series User Manual2-1020-100009-01 Rev.1 (07/08)
2 Installation and Setup
This section explains how to install, and setup the projector for delivery of superior image
quality. 
• 2.1 Projector Quick Setup and Installation
• 2.2 Detailed Setup and Installation
• 2.3 Connecting Sources 

Section 2: Installation and Setup
M-Series User Manual2-2020-100009-01 Rev.1 (07/08)
2.1 PROJECTOR QUICK SETUP AND INSTALLATION
The following instructions are for those preferring a quick setup. Refer to the remaining subsections 
for detailed setup instructions.
 
STEP 1 - INSTALLING A PROJECTION LENS
The projection lens, shipped separately from the projector, must be installed prior to setting up the 
projector. 
 Remove the lens plug from the lens opening in the projector before installing the lens....

M-Series User Manual2-3020-100009-01 Rev.1 (07/08)
 WARNING
Use of the lens security screws is required if the projector is hoisted or installed 
in an overhead position 
F
IGURE 2-1 - LENS INSTALLATIONFIGURE 2-2 - SECURITY SCREW LOCATION
FIGURE 2-3 - LENS PLACEMENT 

Section 2: Installation and Setup
M-Series User Manual2-4020-100009-01 Rev.1 (07/08)
STEP 2 - POSITIONING THE PROJECTOR
Place the projector on a sturdy, level surface and position it so that it is perpendicular to the screen at a 
suitable distance. The further back the projector is positioned for the screen, the larger the image will 
be.
To level the projector adjust its 3 feet. With the projector positioned perpendicular to the screen the 
image will appear rectangular instead of keystoned.
For more...

M-Series User Manual2-5020-100009-01 Rev.1 (07/08)
STEP 4 - CONNECTING THE LINE CORD
IMPORTANT: Use the line cord provided with the projector, or ensure you are using a line cord, 
power plug and socket that meet the appropriate rating standards. NOTE: Listed on the license label.
Connect the projectors line cord to the AC receptacle at the AC inlet of the projector, then push the 
wire clip over the plug to retain it. This prevents the line cord from inadvertent disconnection. Plug the 
3-pronged plug...

Section 2: Installation and Setup
M-Series User Manual2-6020-100009-01 Rev.1 (07/08)
2.2DETAILED SETUP AND INSTALLATION
2.2.1About the Projector
BUILT-IN KEYPAD
The built-in keypad is located on the side of the projector. Use it similarly to the IR remote to control 
the projector. An LCD display is located above the keypad for displaying projector status.
AC RECEPTACLE
The AC receptacle is located at the back of the projector. Use this receptacle to plug in an appropriately 
rated line cord. NOTE: The...

M-Series User Manual2-7020-100009-01 Rev.1 (07/08)
ADJUSTABLE FEET
Located on the underside of the projector are three adjustable feet. Raise or lower these feet when 
positioning the projector to ensure it is level on all sides so the displayed image will appear rectangular 
without any keystone.  
Refer to 2.2.5 Adjusting Projector Height/Tilt
 for instructions on how to adjust the projector’s feet. 
INPUT PANEL
All source connections are made to the input panel located at the back of the projector....

Section 2: Installation and Setup
M-Series User Manual2-8020-100009-01 Rev.1 (07/08)
FRONT & REAR IR SENSORS
The two IR sensors located on the projector receive transmissions from the IR remote from up to 100 
feet away. It is important to keep the transmission path to these sensors unobstructed for uninterrupted 
communications with the projector. The rear IR sensor is located at the back of the projector between 
the status LEDs and the front IR sensor is located next to the projector’s front...