Christie Projector LWU421 User Manual

							19Network Guide020-000475-02 Rev. 1 (06-2012)
LX501/LX601i/LW401/LW551i/LWU421/LWU501i
3.1.3 Network Settings
Displays and configures network settings.
Item Description
Common Setup
Configures the settings common to wireless and wired LAN.
Projector Name Configures the name of the projector.
The length of the Projector Name can be up to 64 
alphanumeric characters. Only alphabets, numbers and 
following symbols can be used. 
  !"#$%&'()*+,-./:;?@[\]^_`{|}~ and space. 
Particular projector name is pre-assigned by default.
sysLocation (SNMP) Configures the location to be referred to when using SNMP.
The length of the sysLocation can be up to 255 alphanumeric 
characters. Only numbers ‘0-9’ and alphabet ‘a-z’, ‘A-Z’ can 
be used.
sysContact (SNMP) Configures the contact information to be referred to when 
using SNMP.
The length of the sysContact can be up to 255 alphanumeric 
characters. Only numbers ‘0-9’ and alphabet ‘a-z’, ‘A-Z’ can 
be used.
AMX D.D.
(AMX Device 
Discovery)
Configures the AMX Device Discovery setting to detect the 
projector from the controllers of AMX connected to the same 
network. For the details of AMX Device Discovery, visit the 
AMX web site. URL: http://www.amx.com (as of Jun. 2012)
(continued on next page) 
3. Web Control
3.1 Projector Web Control (continued) 
						

							20Network Guide020-000475-02 Rev. 1 (06-2012)
LX501/LX601i/LW401/LW551i/LWU421/LWU501i
3.1 Projector Web Control - Network Settings (continued)
3. Web Control
ItemDescription
Wireless Setup Configures the wireless LAN settings.
Mode Select "Ad-Hoc" or "Infrastructure".
IP Configuration Configures network settings.
DHCP ON Enables DHCP.
DHCP OFF Disables DHCP.
IP Address Configures the IP address when DHCP is disabled.
Subnet Mask Configures the subnet mask when DHCP is disabled.
Default 
Gateway Configures the default gateway when DHCP is disabled.
DNS Server Address Configures the DNS server address.
Ch Select from “1” to “11” a channel to use in the Ad-Hoc mode.
Encryption Select data encryption method.
WEP Key Input the WEP key. 
Either ASCII characters or hexadecimal numbers can be 
used during WEP key input. However, you cannot use a 
combination of both.The length of the key is defined as 
follows according to the WEP and character formats.
Encryption
ASCII characters HEX numbers
WEP 64bit 5 characters 10 characters
WEP 128bit 13 characters 26 characters
WPA Passphrase Input WPA Passphrase.  
Available number of input characters is 8 to 63. Only 
alphabets, numbers and following symbols can be used. 
 !"#$%&'()*+,-./:;?@ [\]^_`{|}~ and space
SSID Select an SSID from the list.  
If you require to set your unique SSID, select 
[Custom], then 
set your own SSID following the rules below. 
Maximum number of input characters is 32. 
Only alphabets, numbers and following symbols can be used.
 !"#$%&'()*+,-./:;?@[\]^_`{|}~ and space.
(continued on next page)
• Depending on the country where you are 
the channels may vary. In addition, depending on the 
country or region where you are may be required to use a 
wireless network card that confirm to the standards in the 
respective country or region.NOTE 
						

							21Network Guide020-000475-02 Rev. 1 (06-2012)
LX501/LX601i/LW401/LW551i/LWU421/LWU501i
Click the [Apply] button to save the settings. 3.1 Projector Web Control - Network Settings (continued)
ItemDescription
Wired Setup Configures the wired LAN settings.
IP Configuration Configures network settings.
DHCP ON Enables DHCP.
DHCP OFF Disables DHCP.
IP Address Configures the IP address when DHCP is disabled.
Subnet Mask Configures the subnet mask when DHCP is disabled.
Default 
Gateway Configures the default gateway when DHCP is disabled.
DNS Server Address Configures the DNS  server address.
Other Setup Configures other network settings.
Crestron e-Control Set whether to or not to use Crestron e-Control
®. 
If you choose Disable, the Logon window of Projector Web 
Control and not the selection window will be displayed at first 
of the Web Control.
3. Web Control
• The new configuration settings are activated after restarting the 
network connection. When the configuration settings are changed, you must 
restart the network connection. You can restart the network connection from 
Network Restart  on the main menu (
&41).
• If you connect the projector to an existing network, consult a network 
administrator before setting server addresses.
• The WEP Key, WPA passphrase and SSID settings will not be set if the invalid 
characters are used.
• The projector does not allow both wireless and wired LAN to be connected to 
the same network. Do not set the same network address for both wireless and 
wired LAN. NOTE 
						

							22Network Guide020-000475-02 Rev. 1 (06-2012)
LX501/LX601i/LW401/LW551i/LWU421/LWU501i
3.1.4 Port Settings
Displays and configures communication port 
settings.
Item Description
Network Control Port1 
(Port:23) Configures command control port 1 (Port:23).
Port open Click the [Enable] check box to use port 23.
Authentication Click the [Enable] check box when authentication is required 
for this port.
Network Control Port2 
(Port:9715) Configures command control port 2 (Port:9715).
Port open Click the [Enable] check box to use port 9715.
Authentication Click the [Enable] check box when authentication is required 
for this port.
PJLink
TM Port   
(Port:4352) Configures the PJLinkTM port (Port:4352).
Port open Click the [Enable] check box to use port 4352.
Authentication Click the [Enable] check box when authentication is required 
for this port.
My Image Port
(Port:9716) Configures the My Image Port (Port:9716).
Port open Click the [Enable] check box to use port 9716.
Authentication Click the [Enable] check box when authentication is required 
for this port.
Messenger Port
(Port:9719) Configures the Messenger Port (Port:9719).
Port open Click the [Enable] check box to use port 9719.
Authentication Click the [Enable] check box when authentication is required 
for this port.
(continued on next page)
3. Web Control
3.1 Projector Web Control (continued) 
						

							23Network Guide020-000475-02 Rev. 1 (06-2012)
LX501/LX601i/LW401/LW551i/LWU421/LWU501i
ItemDescription
SNMP Port Configures the SNMP port.
Port open Click the [Enable] check box to use SNMP.
Trap address Configures the destination of the SNMP Trap in IP format.
• The address allows not only IP address but also domain 
name if the valid DNS server is setup in the 
Network 
Settings. The maximum length of host or domain name is up 
to 255 characters.
Download MIB file Downloads a MIB file from the projector.
Network Bridge Port Configures the Bridge port number.
Port number Input the port number. 
Except for 41794, 9715, 9716, 9719, 9720, 5900, 5500, 4352 
between 1024 and 65535 can be set up. It is set to 9717 as 
the default setting.
Click the [Apply] button to save the settings. 3.1 Projector Web Control - Port Settings (continued)
• The new configuration settings are activated after restarting the 
network connection. When the configuration settings are changed, you must 
restart the network connection. You can restart the network connection from 
Network Restart  on the main menu(
&41).
NOTE
3. Web Control 
						

							24Network Guide020-000475-02 Rev. 1 (06-2012)
LX501/LX601i/LW401/LW551i/LWU421/LWU501i
3.1.5 Mail Settings
Displays and configures e-mail addressing 
settings.
Item Description
Send Mail Click the [Enable] check box to use the e-mail function. 
Configure the conditions for sending e-mail under the 
Alert 
Settings.
SMTP Server Address Configures the address of the mail server in IP format.
• The address allows not only IP address but also domain 
name if the valid DNS server is setup in the 
Network 
Settings. The maximum length of host or domain name is up 
to 255 characters.
Sender E-mail address Configures the sender e-mail address. 
The length of the sender e-mail address can be up to 255 
alphanumeric characters.
Recipient E-mail address Configures the e-mail address of up to five recipients. You 
can also specify the [to] or [cc] for each address. The 
length of the recipient e-mail address can be up to 255 
alphanumeric characters.
Click the [Apply] button to save the settings.
• You can confirm whether the mail settings work correctly using the 
[Send Test Mail] button. Please enable Send mail setting before clicking the 
[Send Test Mail]. 
• If you connect the projector to an existing network, consult a network 
administrator before setting server addresses. NOTE
3. Web Control
3.1 Projector Web Control (continued) 
						

							25Network Guide020-000475-02 Rev. 1 (06-2012)
LX501/LX601i/LW401/LW551i/LWU421/LWU501i
3.1.6 Alert Settings
Displays and configures failure & alert settings.
Item Description
Cover Error The lamp cover has not been properly fixed.
Fan Error The cooling fan is not operating.
Lamp Error The lamp does not light, and there is a possibility that interior 
portion has become heated.
Temp Error
There is a possibility that the interior portion has become heated.
Air Flow Error The internal temperature is rising.
Cold Error There is a possibility that the interior portion has become 
overcooled.
Filter Error Filter time over.
Other Error Other error.
If displaying this error, please contact your dealer.
Schedule Execution 
Error Schedule Execution error. (
&27)
Lamp Time Alarm Lamp time over Alarm Time setting.
Filter Time Alarm Filter time over Alarm Time setting.
Filter Status Notification The status to clean the air filter is changed.
Transition Detector 
Alarm Transition Detector Alarm. (
&
SECURITY menu in the 
Operating Guide )
Cold Start When the projector is supplied with the power, it works as 
below.
• 
If the STANDBY MODE is set to the NORMAL:the projector's 
power status changes from “OFF” to “Standby state”.
• If the STANDBY MODE is set to the SAVING:the projector's power 
status changes from “Standby state” to “ON (lamp is turned on)”.
(& SETUP menu in the Operating Guide
)
Authentication Failure
The SNMP access is detected from the invalid SNMP community.
Refer to &Troubleshooting  in the Operating Guide  for further detailed 
explanation of Error except Other Error and Schedule Execution Error .
3. Web Control
3.1 Projector Web Control (continued) 
						

							26Network Guide020-000475-02 Rev. 1 (06-2012)
LX501/LX601i/LW401/LW551i/LWU421/LWU501i
The Alert Items are shown below.
ItemDescription
Alarm Time Configures the time to alert.
(Only Lamp Time Alarm and Filter Time Alarm.)
SNMP Trap Click the [Enable] check box to enable SNMP Trap alerts.
Send Mail Click the [Enable] check box to enable e-mail alerts.
(Except Cold Start and Authentication Failure
.)
Mail Subject Configures the subject line of the e-mail to be sent. 
The length of the subject line can be up to 100 alphanumeric 
characters.
(Except Cold Start and Authentication Failure
.)
Mail Text Configures the text of the e-mail to be sent. 
The length of the text can be up to 1024 alphanumeric 
characters, but if you are using some of special characters 
below the length may be shorter.
     Special characters  " ' : & , % \  
and space(Except Cold Start and Authentication Failure
.)
Click the [Apply] button to save the settings.
• The trigger of Filter Error e-mail is depending on the FILTER 
MESSAGE setting in the SERVICE item of the OPTION menu which defines 
the period until the filter message is displayed on the projector screen.  An 
e-mail will be sent when the usage time of the filter exceeds the time limit that is 
set. No notification e-mail will be sent if the FILTER MESSAGE is set to TURN 
OFF. (
&OPTION menu  in the Operating Guide )
• Lamp Time Alarm is defined as a threshold for e-mail notification (reminder) 
of the lamp time. When the lamp hour exceeds the limit that is configured in the 
Projector Web Control, an e-mail will be sent.
• Filter Time Alarm is defined as a threshold for e-mail notification (reminder) 
of the filter time. When the filter hour exceeds the limit that is configured in the 
Projector Web Control, an e-mail will be sent.
• Filter Status Notification  can be enabled for both or either one of  Status 
1 and 2. These notifications are equivalent to the changing of the  FILTER 
indicator on the projector. (Status 1: off to orange, Status 2: orange to red) 
Refer to the Operating Guide  for details of the FILTER indicator.
NOTE
3.1 Projector Web Control - Alert Settings (continued)
3. Web Control 
						

							27Network Guide020-000475-02 Rev. 1 (06-2012)
LX501/LX601i/LW401/LW551i/LWU421/LWU501i
3.1.7 Schedule Settings
Displays and configures schedule settings.
Item Description
Daily Configures the daily schedule.
Sunday Configures the Sunday schedule.
Monday Configures the Monday schedule.
Tuesday Configures the Tuesday schedule.
Wednesday Configures the Wednesday schedule.
Thursday Configures the Thursday schedule.
Friday Configures the Friday schedule.
Saturday Configures the Saturday schedule.
Specific date No.1 Configures the specific date (No.1) schedule.
Specific date No.2 Configures the specific date (No.2) schedule.
Specific date No.3 Configures the specific date (No.3) schedule.
Specific date No.4 Configures the specific date (No.4) schedule.
Specific date No.5 Configures the specific date (No.5) schedule.
3. Web Control
3.1 Projector Web Control (continued) 
						

							28Network Guide020-000475-02 Rev. 1 (06-2012)
LX501/LX601i/LW401/LW551i/LWU421/LWU501i
3.1 Projector Web Control - Schedule Settings (continued)
The schedule settings are shown below.
ItemDescription
Schedule Click the [Enable] check box to enable the schedule.
Date (Month/Day) Configures the month and date.
This item appears only when Specific date (No. 1-5) is 
selected.
Click the [Apply] button to save the settings.
The current event settings are displayed on the schedule list. To add additional 
functions and events, set the following items.
Item
Description
Time Configures the time to execute commands.
Command
[Parameter] Configures the commands to be executed.
Power  Configures the parameters for power control.
Input Source  Configures the parameters for input switching.
My Image Configures the parameters for My Image data display. (
&50)
Messenger Configures the parameters for Messenger data display. (
&51)
Slideshow Configures the Start/Stop parameters for the Slideshow.
Click the [Register] button to add new commands to the schedule list.
Click the [Delete] button to delete commands from the schedule list.
Click the [Reset] button to delete all commands and reset the schedule settings 
from the schedule list.
3. Web Control