Christie Projector J Series 2.0, 2.4, And 3.0kW User Manual
Have a look at the manual Christie Projector J Series 2.0, 2.4, And 3.0kW User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 476 Christie manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Section 7: Specifications J Series 2.0, 2.4, and 3.0kW User Manual7-3020-100707-01 Rev. 1 (10-2011) 7.1.9 Blemishes 7.1.10 Pixel Defects 7.2 Feature Set 7.2.1 Airflow 7.2.2 Air Filters (Optional) 7.2.3 Dust Sealing 7.2.4 ILS (Intelligent Lens System) Red screen No blemishes Green screen No blemishes Blue screen No blemishes White screen No blemishes Black screen No blemishes Red 0 bright, up to 1 dark Green 0 bright, 0 dark Blue 0 bright, up to 2 dark non-adjacent Air intakes Front of projector Air exhaust Hot lamp exhaust: rear of projector Filter media types Dust filter Fog filter Filter access Service-interchangeable via access panel Dust sealed DMDs Gasket sealed Motorized lenses and lens mount with position encoding Zoom, focus, horizontal and vertical offsets Accuracy ±2 pixel Manual control 1/3 pixel fine movement control per button press on any applicable User Interface (e.g., remote). Calibration User Configurable Calibration ModesAutomatic calibration on lens change detection Automatic calibration on power-up Manual calibration Calibration time < 10 secs when required Bore sight 3-point +- 4 degrees adjustment and lockable without removing covers Travel time stop to stop Zoom and Focus 10 sec nominal (depends on lens type) Offsets 5 sec (nominal (depends on lens type) Manual Lens Movement Manual over-ride permissible for zoom and focus
7-4J Series 2.0, 2.4, and 3.0kW User Manual020-100707-01 Rev. 1 (10-2011) Section 7: Specifications 7.2.5 Projection Lens Compatibility Lens Throw Ratio 7.2.6 Automatic Fans 7.2.7 Constant Lamp Output Management Lens type Reverse Telecentric Internal-focus Motorized zoom and focus with position feedback NOTE: Calculated Throw distance values are subject to a ±5% lens tolerance Throw Ratio Lens DescriptionPart NumberSXGA+HDWUXGA FixedLens ILS 0.73:1SX+/0.67:1HD118-100110-xx 0.73 0.67 0.67 Lens ILS 1.2SX+/1.1HD 118-100117-xx 1.2 1.1 1.1 ZoomLens ILS 1.25-1.6SX+/1.16-1.49HD 118-100111-xx 1.25-1.6 1.16-1.49 1.16-1.49 Lens ILS 1.5-2.0SX+/1.4-1.8HD118-100112-xx 1.5-2.0 1.4-1.8 1.4-1.8 Lens ILS 2.0-2.8SX+/1.8-2.6HD118-100113-xx 2.0-2.8 1.8-2.6 1.8-2.6 Lens ILS 2.8-4.5SX+/2.6-4.1HD118-100114-xx 2.8-4.5 2.6-4.1 2.6-4.1 Lens ILS 4.5-7.5SX+/4.1-6.9HD 118-100115-xx 4.5-7.5 4.1-6.9 4.1-6.9 Lens ILS 7.5-11.2SX+/6.9-10.4HD118-100116-xx 7.5-11.2 6.9-10.4 6.9-10.4 Temperature sensitive fan speed control Fans automatically adjust to required speed to maintain projector at proper operating range as function of outside ambient temperature. Standby All fans are off, except integrated LVPS fan, when projector is in standby. Temperature range 5 to 40 degrees C Transition steps Smooth speed transitions with no abrupt audible changes. (Factory Optional) Yellow notch filter Fixed filter to enhance color space LiteLOC Automatically adjusts lamp output to maintain constant lumens setting within operating range of lamp.
Section 7: Specifications J Series 2.0, 2.4, and 3.0kW User Manual7-5020-100707-01 Rev. 1 (10-2011) 7.2.8 Shutter 7.2.9 Lamps 7.2.10 Status LED 7.2.11 Electronics/SW Open Light transmitted to projection lens Closed All light blocked - no light on screen Ushio Xenon bubble lamp system Lamps are accessed from the rear of the projector Status LEDs # LED STATES Lamp1 Off – Lamp off Yellow – Lamp time has expired and lamp should be replaced Green – Lamp is on and operating correctly Flashing red – Lamp has malfunctioned Flashing yellow – Lamp door is open Comm2 Flashing red – Error has occurred. Details are displayed on the status display Status3 Off – AC power is off Yellow – AC is present but projector is in standby Green – Power is powered up and operating normally Flashing red – Error has occurred. Details are displayed on the status display Shutter4 Green – Shutter is open Yellow – Shutter is closed FEATURE COMMENTS Image Device Supports 3 chip DMD operation Video Format Re-Sizing All video formats can be resized to fill screen either horizontally or vertically while maintaining aspect ratio Picture in Picture Supported Built-in 2D keystone and geometry correction Supported Auto-scaling Supported Auto-de interlacing Supported Edge blending Supported Warping Supported Tiling (max array size) 3x3 Standard Image Processor & 2x2 Dual Image Processor Blanking and Image positioning Supported Brightness, contrast, color, and uniformity User settable control Image orientation Can display image front/rear screen, normal/inverted (ceiling) Electronics HW access Mounted at the back of the projector Number of option cards 6 user inter-changeable – hot swappable Number of processor cards 2 user inter-changeable Number of option slots 4, option cards; 1, processor card Arbitrary Gamma User definable gamma curves
7-6J Series 2.0, 2.4, and 3.0kW User Manual020-100707-01 Rev. 1 (10-2011) Section 7: Specifications 7.3 Image Processor Performance 7.4 Input (Source Signal) Compatibility 7.4.1 Analog (Only) Input 7.4.2 Twin HDMI Input Min input pixel rate 13 Mpix/s Max input pixel rate 165 Mpix/s Standard Mode 330 Mpix/s High Bandwidth modeStandard Image Processor Dual Image Processor Max input resolution 2048x1536 (QXGA) Min input resolution 640x400 Max input frame rate with Dual Image Processor Card120Hz at 2048x1080 92Hz at 2048x1536*Dual Image Processor (DIPC) required * QXGA with sources that can output minimum blanking Max imput frame rate with Standard Image Processor Card50Hz at 2048x1536 (QXGA) *With sources that can output minimum blanking, otherwise lower vertical rates Processing 10 bit throughout * * Except Dual-DVI input in dual-link mode (dual 8 bit input paths into 10 bit processing) Source switching time Switch time 1 second Switch time 3 secondsLow bandwidth signals 3D signals Connectors 5 female BNC, 75 Ohm R/Pr G/Y B/Pb H/C V Color spaces/signal types RGB YPbPr A/D conversion 10 bits Connectors 2 independent HDMI inputs type A 2 loop-out HDMI connectors type A Color spaces/signal types RGB YCbCr (4:2:2) YCbCr (4:4:4) HDCP support HDMI 1.3 supported (not including audio) except: 12 bit color dithered to 10 bits; 16 bit color not supported HDMI 1.4a (Mirage Models)
Section 7: Specifications J Series 2.0, 2.4, and 3.0kW User Manual7-7020-100707-01 Rev. 1 (10-2011) 7.4.3 Dual Link DVI Input 7.4.4 Video Decoder Input 7.4.5 Dual 3G/HD/SD - SDI Input 7.5 Control Signal Compatibility 7.5.1 Projector Control 7.5.2 Control Receiver Connectors 1 dual link DVI-I 1 analog 15-pin VGA Color spaces/signal types HDCP support A/D conversion 10 bits for single link DVI input 8 bits for dual link DVI inputs Frequency 165 MPixel/s analog 330 Mpix/s Dual link DVI (requires DIPC) Connectors 2 S-Video 4-pin miniature DIN 4 BNC, 75 Ohm 2 independent decoder channels for PIP Color space/Signal types Composite video Component video (SD and ED only) S-video Video Standards NTSC, NTSC 4.43, PAL, PAL M, PAL N, PAL 60, SECAM A/D conversion 10 bits Connectors BNC, 75 Ohm Color spaces/signal types Dual HD input SDI, HDSDI, 3GHz Number of transmitters 2 IR Modulation frequency Dual frequency (38 kHz) Range Min 35 m Wired Keypad 3 pin XLR Connection Max cable length 30 m (not supplied) Number of sensors 1 front, 1 rear Coverage 130 degrees coverage in-line with lens at 3 m distance Modulation (carrier) frequency Dual frequency (38 kHz)
7-8J Series 2.0, 2.4, and 3.0kW User Manual020-100707-01 Rev. 1 (10-2011) Section 7: Specifications 7.5.3 RS-232 7.5.4 RS-422 7.5.5 Ethernet 7.5.6 USB 2.0 Device Port 7.5.7 GPIO 7.5.8 DMX512 Interface 7.5.9 Built-In Keypad and Display 7.5.10 Convenience Light Number of ports 2 Connector 1 female 9-pin Dsub (IN) 1 male 9-pin Dsub (OUT) Max bit rate 115.2 kbps Flow control Xon/Xoff Number of ports 1 Connector 1 female 9-pin Dsub Max bit rate 115.2 kbps Power output 12 V ±5% @ 400mA maximum Number of ports 1 Standard 10/100 Base-T Connector Female RJ-45 Number of ports 1 Standard Not supported (non-functional) Number of I/O Lines 7 Connector Male 9-pin Dsub Output sink current (logic low) 100 mA @ 1V typical Power output 12 V ±5% @ 400mA maximum Connectors Two 5-pin XLR one male (input) and one female (output) DMX Chain Termination Configurable via software Key type Soft-touch keys Display type Graphics LCD backlight Illumination for Input Panel Provided by a dual-strip dedicated switch on the built-in keypad.
Section 7: Specifications J Series 2.0, 2.4, and 3.0kW User Manual7-9020-100707-01 Rev. 1 (10-2011) 7.6 Power Requirements 7.6.1 Lamp Specification 7.7 Physical Specifications 7.7.1 Size Parameter Lamp Power Requirement Rated Voltage 3000W 200 VAC - 240 VAC 2400W 200 VAC - 240 VAC 1900W 200 VAC - 240 VAC Rated Current 3000W 20 A 2400W 16 A 1900W 14 A Line Frequency All 50/60 Hz AC Input Coupler 3000W 32 A, 250 VAC, IEC 309 1900W 20 A, 250 VAC, IEC 320-C20 2400W 20 A, 250 VAC, IEC 320-C20 Line Cord 3000W 10AWG type SJT with plug, NEMA L6-30P, 30A 2400W 12AWG type SJT with plug, NEMA 6-20P, 20A 1900W 12AWG type SJT with plug, NEMA 6-20P, 20A Inrush Current All 60 A max Maximum Power Consumption 3000W 4000W 2400W 3200W 1900W 2800W Type Bubble Lamp Power Range Lamp Model 3000W 2000W min., 3000W max (software adjustable) 2400W 1500W min., 2400W max (software adjustable) 2000W 1200W min, 1900W max (software adjustable) Rated lamp life to 50% brightness (2 hrs on, 15 min. off duty cycle) 3000W 750 hrs. min 2400W 750 hrs. min 2000W 1000 hrs. min Warm-up time (to full output) 20 minutes max Operating position Full rotation allowed about the lamp axis, some portrait mode allowed, see Manual text Maximum product dimensions (L x W x H) (with lens removed)815mm (32”) x 621mm (24.5”) x 419mm (16.5”) Maximum shipping dimensions (L x W x H) 1041mm (41”) x 825mm (32.5”) x 749mm (29.5”)
7-10J Series 2.0, 2.4, and 3.0kW User Manual020-100707-01 Rev. 1 (10-2011) Section 7: Specifications 7.7.2 Adjustment 7.7.3 Weight 7.8 Reliability and Serviceability 7.8.1 Reliability 7.8.2 Serviceability 7.9 Environment 7.9.1 Temperature/Humidity/Altitude Product Alignment 50mm (2”) of vertical adjustment on 2 front feet and 2 rear feet. Maximum product weight (with lens removed) 72.5kg (160lb.) Maximum shipping weight (includes packaging) 91kg (200lb.) MTBF – excluding consumable components 11,000 hrs Consumable components Air filters, fans, lamps MTTR, average 30 min Time to replace any option card 1 minute maximum Time to replace lamp 1 minute maximum Time to replace projection lens 30 seconds maximum Time to replace air filter 1 minute maximum Operating temperature range 5 to 40 degrees C Storage temperature range -40 to 70 degrees C Humidity range 10% to 80%, non condensing Operating Altitude 10,000 ft. maximum
Section 7: Specifications J Series 2.0, 2.4, and 3.0kW User Manual7-11020-100707-01 Rev. 1 (10-2011) 7.10 Accessories and Service Components 7.11 Regulatory 7.11.1 Safety • CAN/CSA C22.2 No. 60950-1-07 2nd Edition • UL 60950-1, 2nd Edition • IEC 60950-1:2005, 2nd Edition • EN60950:2006 + A11:2009 Product NamePart NumberSold With ProductSold Separately Analog Input 108-309101-XX X X Dual Link DVI Input 108-312101-XX X X Video Decoder Input 108-310101-XX X X Dual 3G/HD/SD-SDI Input Card 108-313101-XX X X Twin HDMI Input 108-311101-XX X X DMX512 Interface 108-314101-XX X X Dust Filter X X Fog FilterX Lens ILS 0.73:1SX+/0.67:1HD 118-100110-XX X Lens ILS 1.25-1.6SX+/1.16-1.49HD 118-100111-XX X Lens ILS 1.5-2.0SX+/1.4-1.8HD 118-100112-XX X Lens ILS 2.0-2.8SX+/1.8-2.6HD 118-100113-XX X Lens ILS 2.8-4.5SX+/2.6-4.1HD 118-100114-XX X Lens ILS 4.5-7.5SX+/4.1-6.9HD 118-100115-XX X Lens ILS 7.5-11.2SX+/6.9-10.4HD 118-100116-XX X Lens ILS 1.2SX+/1.1HD 118-100117-XX X Lens ILS 1.2SX+/1.1HD 118-101103-XX X ILS Lens Conversion Kit 108-331108-XX X Lens Conversion Kit X CT MOUNT Xe Bubble 132-112105-XX X Kit Upgrade to Mirage X YNF Upgrade 132-110103-XX X AutoSTACK 108-308101-XX X Handle 104-108101-XX X Edge Blending CT 104-102101-XX X Remote IR Sensor 104-106101-XX X Portrait Adapter 118-116109-XX X
7-12J Series 2.0, 2.4, and 3.0kW User Manual020-100707-01 Rev. 1 (10-2011) Section 7: Specifications 7.11.2 Electro-Magnetic Compatibility Emissions • FCC CFR47, Part 15, Subpart B, Class A - Unintentional Radiators • CISPR 22: 2008-09/EN55022: 2006 + A1:2007 Class A - Information Technology Equipment Immunity • CISPR 24: 1997 +A1:2001+A2:2002/ EN55024: 1998 +A1:2001 +A2:2003 EMC Requirements - Infor- mation Technology Equipment 7.11.3 Environmental The product must conform to: • EU Directive (2002/95/EC) on the restriction of the use of certain hazardous substances (RoHS) in electrical and electronic equipment and the applicable official amendment(s). • EU Regulation (EC) No. 1907/2006 on the registration, evaluation, authorization and restriction of chemicals (REACH) and the applicable official amendments. • EU Directive (2002/96/EC) on waste and electrical and electronic equipment (WEEE) and the applicable official amendment(s). • China Ministry of Information Industry Order No.39 (02/2006) on the control of pollution caused by elec- tronic information products, the hazardous substances concentration limits (SJ/T11363-2006), and the appli- cable product marking requirement (SJ/T11364-2006). 7.11.4 Marking This product shall conform to all relevant Canadian, US, and European directives, standards, safety, health and environmental concerns and bears the following markings at product launch: •UL •CE • RoHS • WEEE • Future International Certifications to include: CCC, KC, PSE, c-tick, Gost-R, South Africa • International packaging recycling mark requirements: • EU Directive (94/62/EC) on packaging and packaging waste; • China packaging recycling mark standard (GB18455-2001); • Korea extended producer responsibility (EPR) separate discharge mark system under the act on the promo- tion of resource saving and recycling (2003); • United States society of the plastics industry (SPI) resin identification code (1988); • ISO standards on marking of plastics (11469:2000, 1043-1:2001, 1043-2:2000, 1043-3:1996, and 1043- 4:1998).