Christie Projector DWU700-GS User Manual

							   Operation
GS Series User Manual41
020-001044-02 Rev. 1 (07-2016)
Saturation
Note the following about adjusted saturation:
• The saturation can be adjusted independently for each color (R,G,B,C,M, and Y).
• A saturation level of 0 removes all color from that region.
• A saturation level of 254 sets the color region to have maximum color.
• A saturation level of 127 does not change the saturation.
Gain
Note the following about adjusted gain: • The gain can be adjusted independently for each color (R,G,B,C,M,Y, and W).
• The range of input is 0 to 254.
• The gain changes the intensity level of the respective color.
• A gain level of 127 disables the HSG controls for that color.
• A gain level less than 127 darkens the respective color.
• A gain level of 254 sets the color region to have maximum gain; however, clipping occurs on the signal.
• A gain of 127 is the nominal setting.
• White provides three gain level controls, one each for the R,G,B component of white. 
						

							   Operation
GS Series User Manual42
020-001044-02 Rev. 1 (07-2016)
Light Source menu
The Light Source menu sets the light source mode and power preferences.
Menu itemDescriptionOptions
Light Source 
Mode Sets the light source mode.
• Constant Power
• Constant Intensity
• ECO 1/ECO 2
• Rental Mode—Adjusts to the lowest fan  speeds and switches  the laser diode power 
to the minimum setting.
Constant Power Sets the value of the laser diode power. —
Constant 
Intensity Sets the value for the Constant Intensity 
mode to maintain constant brightness.
The light sensor monitors the light level and 
consumes more power as
 the laser brightness 
decays naturally over time. When the laser 
setting reaches the maximum power, it 
remains at this setting.
Note the following:
• Light sensor must be calibrated for  Constant Intensity mode to work properly. 
The calibration must be  performed after the 
laser diode replacement.
• Constant Intensity mode  is disabled if Light 
Sensor Calibration is not completed.
• Constant Power mode and Constant  Intensity mode conflict with each other. 
When one function is  enabled, the other 
function is automatically disabled.
• When Constant Intens ity mode is enabled, 
the Dymanic Black and RealBlack functions 
are automatically disabled. —
Light Source 
Info Displays information about the light source in 
the projector. • Total Projector Hours—Displays the current 
total number of hours the projector has been 
used.
• LD Hours—Displays the current total number  of hours the laser diode has been used.
Light Sensor Calibrates the light sensor. —
Light Source
1.  Light Source Mode
2.  Constant Power
4.  Light Source Info
5.  Light Sensor Constant Power
3.  Constant Intensity 
						

							   Operation
GS Series User Manual43
020-001044-02 Rev. 1 (07-2016)
Status menu
The read-only Status menu lists a variety of details about the standard and optional components 
currently detected in the projector.
For DHD models
Status
Model Name
Sync On Green
Main Sync Type Serial Number
Native Resolution
Firmware
Main Input
Main Signal Format
Main Pixel Clock
Main Horz Refresh
Main Vert Refresh
PIP/PBP Input
PIP/PBP Signal Format
PIP/PBP Pixel Clock
PIP/PBP Sync Type
PIP/PBP Horz Refresh
PIP/PBP Vert Refresh
Light Source Power
Total Projector Hours
Standby Mode
Lens Lock Settings
IP Address
DHCP
System Temperature 0.5W Mode
Allow
Light Source Hours
LC Hours
No DHD850-GS 
						

							   Operation
GS Series User Manual44
020-001044-02 Rev. 1 (07-2016)
For DW U models
Status
Model Name
Sync On Green
Main Sync Type Serial Number
Native Resolution
Firmware
Main Input
Main Signal Format
Main Pixel Clock
Main Horz Refresh
Main Vert Refresh
PIP/PBP Input
PIP/PBP Signal Format
PIP/PBP Pixel Clock
PIP/PBP Sync Type
PIP/PBP Horz Refresh
PIP/PBP Vert Refresh
Light Source Power
Total Projector Hours
Standby Mode
Lens Lock Settings
IP Address
DHCP
System Temperature 0.5W Mode
Allow
Light Source Hours
LC Hours
No DWU850-GS 
						

							   Operation
GS Series User Manual45
020-001044-02 Rev. 1 (07-2016)
Input Switching & PIP menu
The Input Switching & PIP menu determines ho w the main and PIP/PBP inputs are handled.
Menu itemDescriptionOptions
Main Input Selects an active input to be used as the main 
image. —
PIP/PBP Input Selects an active input to be used as the PIP/ PBP. —
PIP/PBP Enable Toggles between displaying two sources at  once (main and PIP/PBP images) or one 
source only. 
Refer to Inputs on page 71 and  PIP/PBP 
compatibility on page 75. • Selected checkbox—Turns the PIP/PBP 
source on
.
• Cleared checkbox—Turns the PIP/PBP source off.
Swap Changes the main image to PIP/PBP, and the  PIP/PBP to main image.
Swapping is available only when PIP/PBP is 
enabled. —
Size Selects the PIP/PBP size to small, medium, or  large. —
Main Layout Sets the location of the PIP/PBP image on the  screen. —
Timing Detection 
Mode Sets timing detection mode to wide or normal 
to support additional 
PC timings. When the 
projected picture is  not completed, this 
function is used to adjust the picture.
For 4:3 input sources not recognized by Wide 
mode (for example 1400 x 1050), perform 
Auto Image using Normal mode. • Normal mode—Supports 4:3 input sources.
• Wide mode—Supports 
the 16:9 input source 
and most 4:3 input sources. 
Source Info Displays the curre nt source settings. (Read-
only) —
Input key Lists or changes the sources. —
Input Switching & PIP VGA
1.  Main Input
HDMI1
2.  PIP/PBP Input
Medium
5.  Size
Top Right
6.  Main Layout
Auto Source
7.  Timing Detection Mode 3.  PIP/PBP Enable
4.  Swap
8.  Source Info
9.  Input Key
10. Blank on Signal Switch 
						

							   Operation
GS Series User Manual46
020-001044-02 Rev. 1 (07-2016)
PIP/PBP layout and size
A P indicates the primary source region (lighter color) and an asterisk (*) indicates both regions are 
the same size.
Blank on Signal 
Switch Blanks the screen before 
timing is stable when 
changing the source. • On—Blanks the screen
 before timing is 
stable when charging source.
• Off—Disables blanking the screen.
PIP/PBP LayoutPIP/PBP Size
SmallMediumLarge
PBP, Bigger Left
Over-Under, Bigger Upper
PBP, Bigger Right
Over-Under, Bigger Lower
PIP-Bottom Right
PIP-Bottom Left
PIP-Top Left
PIP-Top Right
Menu itemDescriptionOptions
PPP
PPP
PPP
PPP
PPP
PPP
PPP
PPP 
						

							   Operation
GS Series User Manual47
020-001044-02 Rev. 1 (07-2016)
Language menu
Select an available language for the on-screen display.
Test Pattern menu
Choose the required internal test pattern to display, or select Off to turn off a test pattern.
Web user interface
The web user interface provides an alternate way to access the menu functionality on the projector.
Language
Test Pattern
1. Off
2. Grid
3. White
4. Black
5. Checkerboard
6. Color Bars 
						

							   Operation
GS Series User Manual48
020-001044-02 Rev. 1 (07-2016)
Logging on to the web user interface
Log onto the web user interface by following the steps below.
1. Open a web browser and type th e IP address (in the address bar) assigned to your projector.
2. From the Access type list, select the log in level.
3. In the Password field, type the password.
4. From the Language list, select the appropriate language.
5. To access the Main window, click  Login. 
						

							   Operation
GS Series User Manual49
020-001044-02 Rev. 1 (07-2016)
Main tab–General
Displays information about the projector, its powe r status, and what is selected for the main and 
PIP/PBP input sources.  
Main tab–Status
Displays the current status of light source, cooling (fans), version numbers and signal (source) 
information.
Main tab–Lens
Controls the focus, lens shift,  and zoom adjustments for the lens.
PanelDescription
ControlSelects main source/PIP source, enables or  disables PIP/PBP, changes the layout or PIP size, 
swap, and change the test pattern.
Projector 
Information Checks the projector information 
for power status, Pic mute status, on-screen display status, IP 
address, and MAC address.
Switch Switches the on or off status of Power, Pic Mute, and on-screen display. 
						

							   Operation
GS Series User Manual50
020-001044-02 Rev. 1 (07-2016)