Christie Projector DHD600-G User Manual

							G Series User Manual020-000648-01  Rev. 3 (02-2014)
Section 4: Operation
4-42
4. Remove the old lamp: Loosen the three captive screws securing the lamp. 
Remove the lamp module slowly and carefully.
5.  Install the new lamp:  Replace the lamp with a new one and tighten the three screws. Make 
sure the lamp is set properly and secure.
6.  Close the lamp door:  Secure the captive screw. 
Put the lamp door back.
7.  Reset the lamp hours: Turn the projector ON and use “Reset Lamp Hours ” after the lamp 
module is replaced.
8.  Once "Reset Lamp Hours" is pressed, a pop up check box will be shown on \
screen to 
ask user to process Auto Brightness Calibration. 
It is strongly recommend to do Auto Brightness Calibration after changin\
g lamp to achieve 
best accuracy of Constant Intensity control. 
						

							G Series User Manual020-000648-01  Rev. 3 (02-2014)
Section 5: Troubleshooting
5-1
5.  TROUBLESHOOTING
If you are unable to resolve an issue using the information provided in \
this 
section, contact your reseller or service center. 
ProblemSolution
 
y No image appears 
on-screen  
-
Make sure all the cables and power connections are 
correctly and securely connected See “Installation”.
 
-
Check if the lamp is securely installed.
 
-
Make sure you have removed the lens cap and the 
projector is switched ON.
 
y Partial, scrolling 
or incorrectly 
displayed image  
-
Press “AUTO” on control panel or on remote control.
 
-
If you are using a PC (for Windows 95, 98, 2000, XP, 
Windows 7):
1. Click the “My Computer” > “Control Panel”  and then 
double - click 
“Display”.
2. Select the “Settings” tab.
3. Verify that your display resolution setting is lower 
than or equal to WUXGA (1920 × 1200).
4. Click on the “Advanced Properties” button. If the 
projector is still not projecting the whole image, 
change the monitor display:
4.1   Verify the resolution setting is lower than or equal 
to WUXGA (1920 × 1200).
4.2  Select the 
“Change” button under the “Monitor” 
tab.
4.3   Click on 
“Show all devices”. Next, select “Standard 
monitor types
” under the SP box; choose the 
resolution mode you need under the 
“Models” 
box. 
4.4  Verify that the resolution setting of the monitor  display is lower than or equal to WUXGA (1920 × 
1200). 
						

							G Series User Manual020-000648-01  Rev. 3 (02-2014)
Section 5: Troubleshooting
5-2
ProblemSolution
 
y Partial, scrolling 
or incorrectly 
displayed image  
-
If you are using a Notebook:
1. Adjust resolution of the computer.
2. Press the keys listed below for your notebook 
manufacturer to send signal out from notebook to 
projector. Example: [Fn]+[F4]
Notebook Brand Function  Keys
Acer [Fn]+[F5]
Asus [Fn]+[F8]
Dell [Fn]+[F8]
Gateway [Fn]+[F4]
IBM/Lenovo [Fn]+[F7]
HP/Compaq [Fn]+[F4]
NEC [Fn]+[F3]
Toshiba [Fn]+[F5]
Mac Apple System Preference 
 Display 
 
Arrangement   Mirror display
 
-
If you experience difficulty changing resolutions or your 
monitor freezes, restart all equipment including the 
projector.
 
y The screen of 
the Notebook 
or PowerBook 
computer is not 
displaying your 
presentation  
-
If you are using a Notebook PC 
Some Notebook PCs may deactivate their own screens 
when a second display device is in use. Each of them has 
a different method of reactivation. Please refer to your 
computer manual for detailed information.
 
y Image is unstable 
or flickering  
-
Use “Pixel Track” and “Pixel Phase” to correct it.
 
-
Change the monitor color setting on your computer.
 
y Image has vertical 
flickering bar  
-
Use “Auto Image” to make an adjustment.
 
-
Check and reconfigure the display mode of your graphic 
card to make it compatible with the projector.  
						

							G Series User Manual020-000648-01  Rev. 3 (02-2014)
Section 5: Troubleshooting
5-3
ProblemSolution
 
y Image is out of 
focus  
-
Make sure both lens caps (front and back) are removed.
 
-
Adjust lens focus to fit.
 
-
Make sure the projection screen is between the required 
distance. 
 
y The image is 
stretched when 
displaying 16:9 
DVD title  
-
When you play anamorphic DVD or 16:9 DVD, the 
projector will show the best image when the projector 
display mode is set to 16:9 in the OSD.
 
-
If you play 4:3 format DVD titles, please change the format 
to 4:3 in the projector OSD.
 
-
If the image is still stretched, you will also need to adjust 
the aspect ratio by setting the display format as 16:9 (wide) 
aspect ratio type on your DVD player.
 
y Image is too small 
or too large  
-
Adjust lens zoom to fit.
 
-
If it does not fill the screen properly, verify that the correct 
lens is in use or change the position of the projector.
 
y Lamp burns out or 
makes a popping 
sound  
-
If the lamp burns out, try power cycling the projector. If 
the lamp doesn't fire or if you hear it make a loud pop, the 
projector will not turn on until the lamp module has been 
replaced. 
						

							G Series User Manual020-000648-01  Rev. 3 (02-2014)
Section 6: Specifications
6-1
6.1  Inputs
6.  SPECIFICATIONS
NOTE: 
™"RB" means "reduced blanking".
Signal 
Type Resolution Frame Rate 
(Hz) HDMI VGA DisplayPort DVI Component  S- video  CVBS
PC 640x350
85● ●
640x400 85● ● ●
640x480 59●
640x480 60● ● ●●
640x480 72● ● ●
640x480 75● ● ●●
640x480 85● ● ●●
720x400 85● ● ●
768x480 60●
768x480 75●
768x480 85●
800x600 50● ●
800x600 56● ● ●
800x600 60● ● ●●
800x600 72● ● ●
800x600 75● ● ●●
800x600 85● ● ●●
848x480 50●
848x480 60●
848x480 75●
848x480 85●
960x600 50●
960x600 60● ●
960x600 75● 
						

							G Series User Manual020-000648-01  Rev. 3 (02-2014)6-2
Signal Type Resolution Frame Rate 
(Hz) HDMI VGA DisplayPort DVI Component  S- video  CVBS
PC 960x600
85●
1024x768 60● ● ●●
1024x768 75● ● ●●
1024x768 85● ● ●●
1064x600 50●
1064x600 60●
1064x600 75● ●
1064x600 85● ●
1152x720 50●
1152x720 60●
1152x720 75●
1152x720 85● ●
1152x864 60● ● ●
1152x864 70● ● ●
1152x864 75● ● ●
1152x864 85● ● ●
1280x720 50● ●
1280x720 60● ● ●●
1280x720 75● ● ●●
1280x720 85● ● ●●
1280x768 60● ● ●
1280x768 75● ● ●
1280x768 85● ● ●
1280x800 50● ● ●●
1280x800 60● ● ●●
1280x800 75● ● ●
1280x800 85● ● ● 
						

							G Series User Manual020-000648-01  Rev. 3 (02-2014)
Section 6: Specifications
6-3
Signal Type Resolution Frame Rate 
(Hz) HDMI VGA DisplayPort DVI Component  S- video  CVBS
PC 1280x960
60● ● ●
1280x960 75● ● ●
1280x960 85● ● ●
1280x1024 50● ●
1280x1024 60● ● ●●
1280x1024 75● ● ●●
1280x1024 85● ● ●●
1360x768 50●
1360x768 60●
1360x768 75●
1360x768 85●
1366x768 60● ● ●●
1400x900 60● ● ●●
1400x1050 50● ●
1400x1050 60● ● ●●
1400x1050 75● ● ●
1440x900 60● ● ●
1440x900 75●
1600x900 60●
1600x1200 50●
1600x1200 60● ● ●●
1680x1050 50● ●
1680x1050 60● ● ●●
1680x1050 75●
1704x960 50●
1704x960 60●
1728x1080 50● 
						

							G Series User Manual020-000648-01  Rev. 3 (02-2014)6-4
Signal Type Resolution Frame Rate 
(Hz) HDMI VGA DisplayPort DVI Component  S- video  CVBS
PC 1728x1080
60●
1864x1050 50●
1864x1050 60●
1920X1080 50● ●
1920X1080 60● ● ●
1920X1200RB 60 ● ●●●
1920X1200RB 50 ● ●●●
NTSC NTSC (M, 4.43) 60 ● ●
PAL PAL (B,G,H,I) 50
● ●
PAL (N) 50 ● ●
PAL (M) 60 ● ●
SECAM SECAM (M) 50 ● ●
480i 60● ● ●●
576i 50● ● ●●
EDTV 480p
60● ● ●●
576p 50● ● ●● 
						

							G Series User Manual020-000648-01  Rev. 3 (02-2014)
Section 6: Specifications
6-5
Signal Type Resolution Frame Rate 
(Hz) HDMI VGA DisplayPort DVI Component  S- video  CVBS
HDTV 1080i
25● ● ●●
1080i 29● ● ●●
1080i 30● ● ●●
720p 50● ● ●●
720p 59● ● ●●
720p 60● ● ●●
1080s 23● ●
1080s 24● ●
1080p 23● ● ●●
1080p 24● ● ●●
1080p 25● ● ●●
1080p 29● ● ●●
1080p 30● ● ●●
1080p 50● ● ●●
1080p 59● ● ●●
1080p 60● ● ●● 
						

							G Series User Manual020-000648-01  Rev. 3 (02-2014)6-6
6.2  PIP/PBP Compatibility
Main
PIP/PBP HDMI DVI-D VGA Component S-Video CVBS RJ45 USB 
Type B
(mini) USB 
Type A Display
-
Port
HDMI -● - - -● ● ● ● ●
DVI-D ●-● ● ● ● - - --
VGA -● - - - - ● ● ● ●
Component - ●- - - - ● ● ● ●
S-Video -● - - - - ● ● ● ●
CVBS -● - - - - ● ● ● ●
RJ45 ●-● ● ● ● - - --
USB Type B 
(mini) ●
-● ● ● ● - - --
USB Type A ●-● ● ● ● - - --
DisplayPort ●-● ● ● ● - - --
● : PIP/PBP combinations are enabled
- : PIP/PBP combinations are disabled