Christie Projector DHD600-G User Manual

G Series User Manual020-000648-01  Rev. 3 (02-2014)
Section 4: Operation
4-2
4.1  Size and Position Menu
Size Presets
Display an image with the detected size, or resize the image by maximizing 
either the height, width or both, or resize to the maximum size possible\
 while 
keeping the original aspect ratio. 
y Auto: Display with the detected size.
 
y Native: Display in its native resolution.
 
y 4:3: Retain 4:3 aspect ratio.
 
y Letterbox: Display with the black borders on the top and bottom.
 
y Full...

G Series User Manual020-000648-01  Rev. 3 (02-2014)
Section 4: Operation
4-3
Pixel Phase
Analog RGB Signals only. Adjust pixel phase when the image still shows 
shimmer or noise after pixel tracking is optimized. Pixel phase can adju\
st the 
phase of the pixel-sampling clock relative to the incoming signal.
Horz Position
Move the image right or left within the area of available pixels.
Vert Position
Move the image up or down within the area of available pixels.
Digital Horz Zoom
Change the size of...

G Series User Manual020-000648-01  Rev. 3 (02-2014)
Section 4: Operation
4-4
 
y Off: No Geometric correction is applied to the image. 
 
y Horz Keystone: Adjust the keystone horizontally and make a more square 
image. Horizontal keystone is used to correct a keystoned image shape 
in which the left and right borders of the image are unequal in length, \
and 
the top and bottom are slanted to one of the sides. This is intended for\
 use 
with horizontally on-axis applications. For horizontally offset...

G Series User Manual020-000648-01  Rev. 3 (02-2014)
Section 4: Operation
4-5
 
y Pincushion/Barrel: Allow for correction for slight curved distortion fro\
m the 
lens or projection surface. 
B
A
D
C
 
y 4-Corner: Allow the image to be squeezed to fit an area defined by moving 
each of the four corners’ x and y position. 
AA
B
B
B
B
AA
 
y Rotation: Allow an image to be rotated – most commonly to level the 
image.  While the image is rotated, the software can crop any content th\
at 
begins to fall off...

G Series User Manual020-000648-01  Rev. 3 (02-2014)
Section 4: Operation
4-6
Auto Image
Force the projector to reacquire and lock to the input signal. This is u\
seful 
when signal quality is marginal. “Normal mode” can support all of the 4:3 input 
sources.
“Wide mode” can support all of the 16:9 input source & most of the 4:3 input 
source. For those 4:3 input sources not recognized by "Wide mode" (exam\
ple 
1400 x 1050), perform Auto Image using “normal mode”. 

G Series User Manual020-000648-01  Rev. 3 (02-2014)
Section 4: Operation
4-7
4.2  Image Settings Menu
Brightness
Adjust the intensity of the image.
Contrast
Adjust the degree of difference between the lightest and darkest parts o\
f the 
picture and change the amount of black and white in the image.
Color Space
Select a color space that has been specifically tuned for the input signal. 
Useful only for analog signals and certain digital sources.
Detail
Select the edge clarity of the image.
Video Options...

G Series User Manual020-000648-01  Rev. 3 (02-2014)
Section 4: Operation
4-8
 
y Video Black Level: Analyze the current input image and calculate an offs\
et 
value which is then added to the analog to digital converter black level\
 
value. This ensures optimum black level for each analog source.
 
y Detect Film: Control film mode detection and determine whether the 
original source of the input video was film or video.
 
y Closed Captions: Control closed caption display while audio is not muted\
. 
If...

G Series User Manual020-000648-01  Rev. 3 (02-2014)
Section 4: Operation
4-9
Advanced Image Settings
 
y Gamma: Select the appropriate gamma from Video, Film, Bright, and CRT.
 
y BrilliantColor™: Produce an expanded on-screen color spectrum that 
delivers enhanced color saturation for bright, true-to-life images.
 
y White Peaking: (video source only) Increase the brightness of whites t\
hat 
are near 100%.
 
y Color Temperature: Change the intensity of the colors. Select a listed 
relative warmth...

G Series User Manual020-000648-01  Rev. 3 (02-2014)
Section 4: Operation
4-10
4.3  Configuration Menu
Language
Allows you to select an available language for the OSD display, from Eng\
lish, 
French, German, Italian, Spanish, Chinese(simplified), Japanese, Korean, and 
Russian.
Lens Settings
 
y Focus and Zoom: Adjust the focus and zoom the image in or out.
 
y Lens Shift: Shift the lens up and down or left and right.
 
y Lock Lens Motors: Select this function to prevent all lens motors from 
moving. It...

G Series User Manual020-000648-01  Rev. 3 (02-2014)
Section 4: Operation
4-11
Menu Preferences
 
y Menu Horz Position: Change the horizontal position of the OSD.
 
y Menu Vert Position: Change the vertical position of the OSD.
 
y Show Messages: Display status messages on the screen.
 
y Menu Transparency: Change OSD menu background to be transparent.
 
y Splash Screen: Choose which splash screen is to be used.
 
y PIN Protect: The PIN (personal identification number) feature allows you 
to password...