Christie Digital Systems Matrix 3500 Model 38-mx3001-01 Users Manual

							41
SETTING
This function turns Projection Lamp off when this projector detects
signal interruption and is not used for a certain period in order to
reduce power consumption and maintain Lamp-life.  (This projector is
shipped with this function ON.)
Power Management function operates to turn Projection Lamp off
when input signal is interrupted and any button is not pressed over 5
minutes.  This function operates as follows;
1. When any input signal is interrupted, “No signal” and counting
down display appears (for 5 minutes).
2. After counting down for 5 minutes, projector lamp and READY
indicator are turned off.
3. When READY indicator flashing, Projection Lamp can be
turned on again (Power Management mode).  
In this Power Management mode, Projection Lamp is
automatically turned on when input signal connected or
projector is operated with any button on Side Control or on
Remote Control Unit again.
Power management
On start
When this function is “On,” projector is automatically turned on just
by switching MAIN ON/OFF SWITCH on.
Note ; B e  sure to turn projector off properly (refer to section
“TURNING OFF PROJECTOR” on P22).  If projector is turned
off in wrong steps, On Start function does not operate
properly.
Time left until Lamp off.
Press SELECT button at this icon to
display other items.
Remote control
This projector has two different remote control codes; factory-set normal code (Code 1) and secondary code (Code 2). This
switching function prevents remote control operation mixture (jam) when operating several projectors or video equipment
together.  
When operating projector in “Code 2,”  both projector and Remote Control Unit must be switched to “Code 2.”  
To change code of Projector;Set Remote control in SETTING MENU to “Code 2.”
To change code of Remote Control Unit;Press both MENU and IMAGE buttons on Remote Control Unit together for over 10 seconds.
After changing code, make sure Remote Control operates properly.  
To return to normal code (Code 1), operate both projector and Remote Control in ways above again. 
NOTE : When batteries of Remote Control Unit are replaced or ALL-OFF switch is turned to “ALL-OFF,”  remote transmit
code automatically returns to normal code (Code 1).  
Lamp Mode
NOTE :After changing Lamp Mode, it can not be switched again for 90 seconds.
This Projector is equipped with 4 Projection Lamps and a number of using lamps can be switched to 4 lamps or 2 lamps.
Using 2 lamps maintain life of Projection Lamps.  
To change over Lamp Mode
1.  Press MENU button and ON-SCREEN MENU will appear.  Press POINT LEFT/RIGHT buttons to select SETTING and
press SELECT button.  Setting dialog box appears.
2. Press POINT DOWN button to move a red frame pointer to “Lamp mode”.  Set 4 lamps mode or 2 lamps mode by
pressing POINT LEFT/RIGHT button(s).  When Lamp Mode is set from 4 lamps mode to 2 lamps mode image
becomes little darker.  When Lamp Mode is set from 2 lamps mode to 4 lamps mode image become brighter
gradually.
Press SELECT button at this icon to
display previous items.
On start
Move a pointer to item and then
press POINT LEFT/RIGHT
button(s). 
						

							42
SETTING
Lamp counter reset
Move pointer to Lamp counter reset and then
press SELECT button.  
Move arrow to
replaced lamp number (Lamp 1, Lamp
2, Lamp 3 or Lamp 4) and then press
SELECT button.
USB
Projector mode
Select   when controlling a projector with computer.
NOTE:Before you control a projector by computer, install USB driver
(optionally sold parts) and set up computer following instruc-
tion in USB driver package. Contact your authorized dealer.
This Projector is equipped with USB port for interactive operation
between a projector and computer. Set mode following steps below.
Wireless Mouse mode
Select   when controlling a computer with Remote Control of
this projector.
Be sure to reset Lamp Counter when Lamp Assembly is replaced.  When Lamp Replace Counter is reset, LAMP
REPLACE indicator stops lighting.
Turn projector on, press MENU button and ON-SCREEN
MENU will appear.  Press POINT LEFT/RIGHT button(s) to
move a red frame pointer to SETTING Menu icon.1
Press POINT DOWN button to move a red frame pointer to
“Lamp counter reset” and then press 
SELECT button.2
Do not reset Lamp Replace Counter except after Projection lamp is
replaced.
Another confirmation dialog box appears and select [Yes] to
reset Lamp Replace Counter.4
Move arrow to replaced lamp number (Lamp 1, Lamp 2, Lamp 3
or Lamp 4) and then press 
SELECT button.  Message Lamp
replace counter Reset? is displayed. Move pointer to [Yes] and
then press SELECT button.3
NOTE:Be sure to reset correct lamp number otherwise LAMP
REPLACE indicator continues lighting.
Message Lamp replace counter Reset? is
displayed. Move pointer to [Yes] and then
press SELECT button.
Closes SETTING MENU.
Quit
1
24
3
Move a pointer to item and then
press POINT LEFT/RIGHT
button(s).
USB
Press SELECT button at this icon to
display previous items. 
						

							43
APPENDIX
OPERATING WIRELESS MOUSE
INSTALLATION
Wireless Remote Control Unit is not only able to operate this projector but also usable as a wireless mouse for most
Personal Computers.  POINT buttons and two CLICK buttons are used for wireless mouse operation.
This Wireless Mouse function is available only when PC mouse pointer is displayed on a projected screen.  When ON-
SCREEN MENU or any message / dialog box is displayed on screen instead of PC mouse pointer, this Wireless Mouse
function can not be used.
Connect mouse port (or USB port) of your computer to Control
Port (or USB connector) of this projector with Control Cable (or
USB cable). (Refer to page 13, 14 for connection.)
Turn a projector on first, and then turn on your computer.  When
computer is switched on first, Wireless Mouse may not work
properly.
1
2
To use Wireless Remote Control Unit as Wireless Mouse for a Personal Computer, installation of mouse driver (not supplied)
is required.  Make sure that mouse driver is properly installed in your computer.  And make sure that mouse port (or USB
port) of a Personal Computer is activated.
OPERATING WIRELESS MOUSE
When controlling a PC mouse pointer, operate Wireless Mouse with POINT button, SELECT button, and RIGHT CLICK
button on Wireless Remote Control Unit.
Used to move PC mouse pointer.  Pointer is moved corresponding
with direction you are pressing.
POINT button
This button has same function as left button in a PC mouse.
SELECT (LEFT CLICK) button
This button has same function as right button in a PC mouse. This
button is not available for controlling this projector.
RIGHT CLICK button
Note :When your computer has no mouse
port, connect Serial Port of your
computer to Control Port of a projector
with Control Cable for Serial Port (not
supplied).
POINT button (Move pointer)
SELECT button
(left button of mouse)
RIGHT CLICK  button
(right button of mouse)
MAINTENANCE
WARNING TEMP. INDICATOR
Ventilation Slots of a projector may be blocked.  In such an event, reposition a projector so that Ventilation Slots are
not obstructed.
Air Filter may be clogged with dust particles.  Clean Air Filter by following section AIR FILTER CARE AND CLEANING
on next page.
1
2
If WARNING TEMP. Indicator remains on after performing above checks, Cooling Fans or Internal Circuits may be
malfunctioning.  Contact service personnel from an authorized dealer or a service station.3
WARNING TEMP. Indicator flashes red and projector is automatically turned off when an internal temperature of a projector
exceeds normal temperature.  Wait at least 5 minutes before turning on projector again. 
When WARNING TEMP. Indicator continues to flash, check items listed below. 
						

							44
APPENDIX
CLEANING PROJECTION LENS
Apply a non-abrasive camera lens cleaner to a soft, dry cleaning cloth.  Avoid using an excessive amount of cleaner.
Abrasive cleaners, solvents or other harsh chemicals might scratch lens.
When a projector is not in use, replace lens cover.
1
3
Lightly wipe cleaning cloth over lens.2
Follow these steps to clean projection lens:
AIR FILTER CARE AND CLEANING
Turn power off, and disconnect AC power cord from AC outlet.1
2
Air Filter prevents dust from accumulating on surface of Projection Lens and Projection  Mirror.  Should Air Filter
become clogged with dust particles, it will reduce Cooling Fans effectiveness and may result in internal heat
build up and adversely affect life of a projector.
Clean Air Filter following steps below: 
3
4
RECOMMENDATION
We recommend avoiding dusty/smoky environments when operating a projector.  Usage in these
environments may cause poor image quality.
When using under dusty or smoky conditions, dust may accumulate on liquid crystal panel, lens, or optical elements inside it.
This condition may degrade quality of projected image.
When above symptoms are noticed, contact your authorized dealer or service station for proper cleaning.
Pull out air filter from a projector.
Pulling up center frame of air filter top, separate air filter top and
sheet from air filter base.
Clean each parts with brush or wash out dust and particles. Be
sure to dry them out.
Assemble sheet and air filter and replace air filter to a projector.5
AIR FILTER
AIR FILTER
TOP
AIR FILTER
BASESHEET
CAUTION
Do not operate a projector with Air Filter
removed.  Dust may accumulate on LCD
Panel and Mirror degrading picture quality.
Do not put small parts into Air Intake Vents.
It may result in malfunction of a projector. 
						

							45
APPENDIX
LAMP MANAGEMENT
This Projector is equipped with 4 Projection Lamps to ensure brighter image and those lamps are controlled by Lamp
Management Function.  Lamp Management Function detects status of all lamps and shows status on screen or on LAMP
REPLACE indicator.  This function also automatically controls Lamp Mode when any of lamps is out for end of life or
malfunctions. 
Projection Lamp lights normally.
Lamp Replace Indicator
This LAMP REPLACE indicator lights yellow when any of Projection Lamps is nearing its end, and flashes when any of them
becomes out.  Check number of  lamp on Lamp Status Display and replace lamp.
Yellow Lamp
Dim Lamp
X Mark on Lamp
Red Lamp
LAMP REPLACE
INDICATOR
Projection Lamp is turned off.
Projection Lamp is nearing its end.  When image becomes
darker or color becomes unnatural, replace lamp.  (LAMP
REPLACE indicator lights yellow.)
(LAMP REPLACE indicator flashes yellow.)
Projection lamp is defective or fails to be turned on. Restart
a projector on, and make sure lamp is on. If this mark still
appears, replace lamp corresponding with number marked
X.LAMP STATUS
DISPLAY
1
4
3
2
Lamp Mode Changeover
Lamp Management Function automatically changes combination of lighting lamp (Lamp Mode) by detecting status of lamp.
When any of 4 lamps becomes out, Lamp Mode is changed over from 4 lamps to 2 lamps.  And when any of 2 lamps are out,
a projector operates with 1 lamp.  Lamp Mode can be switched to 4 lamps or 2 lamps manually.  Refer to SETTING section
on page 40, 41
.
1
24
31
4
3
2
4 LAMP MODE2 LAMP MODE
(Example)
13
24
1 LAMP MODE
(Example)
Lamp Status Display
Lamp Status Display appears on screen when power switch is on or changed input position (input 1, input 2, Input 3 or input 4).
This shows status of each lamp as; ON, OFF, NEAR END, or OUT.  Refer to following for each status.
30
LAMP STATUS
INPUT 1
1
24
3 
						

							46
APPENDIX
Check number of lamp to be replaced on Lamp Status Display.
Remove two screws on Lamp Cover and press button to open
Lamp Cover.  (See right figure.)
1
3
Loosen two screws and pull out Lamp Assembly to be replaced
by grasping handle.4
Turn off a projector and disconnect AC Power Cord.  Allow a
projector to cool down for at least 45 minutes.2
Replace Lamp Assembly with a new one and tighten two screws.
Make sure Lamp is set properly
6
Follow these steps to replace lamp assembly.
Replace Lamp Cover and tighten two screws. 
5
7
8
Connect AC Power Cord to a projector and turn a projector on.
Reset Lamp Replacement Counter. (Refer to section Lamp
Counter Reset on page 42.)
NOTE :Do not reset LAMP REPLACEMENT COUNTER when
lamp is not replaced.
BUTTON
SCREWS
LAMP
COVER
SCREWS
Make sure which number of lamp needs to be
replaced on Lamp Status Display.
Figure shows case of replacing LAMP 2.LAMP 1
LAMP 2LAMP 3
LAMP 4
CAUTION :DO NOT OPERATE A PROJECTOR WHILE ANY OF LAMPS IS REMOVED. IT MAY
RESULT IN MALFUNCTIONS, FIRE HAZARD, OR OTHER ACCIDENTS.
NOTES ON LAMP REPLACEMENT
To maintain quality of picture (better balance of color and brightness in entire screen), we recommend replacing
all 4 lamps at a time. 
LAMP REPLACEMENT
When the life of the Projection Lamp of this projector draws to an end,
the LAMP REPLACE indicator lights yellow.  If this indicator lights
yellow, replace the projection lamp with a new one promptly.
For continued safety, replace with a lamp assembly of
the same type.
Do not drop a lamp assembly or touch a glass bulb! The
glass can shatter and may cause injury.Allow a projector to cool, for at least 45 minutes before
you open Lamp Cover.  The inside of a projector can
become very hot.
REAR INDICATORS
CAUTION
READYLAMP
LAMP
REPLACEWARNING
TEMP.
WARNING
TEMP. READY
LAMP
REPLACELAMP
FRONT INDICATORS
LAMP REPLACE
INDICATOR 
						

							47
APPENDIX
This projector uses a high-pressure lamp which must be handled carefully and properly.  Improper
handling may result in accidents, injury, or create a fire hazard.
Lamp lifetime may differ from lamp to lamp and according to the environment of use.  There is no
guarantee of the same lifetime for each lamp.  Some lamps may fail or terminate their lifetime in a
shorter period of time than other similar lamps.
If the projector indicates that the lamp should be replaced, i.e., if the LAMP REPLACE INDICATOR
lights up, replace the lamp with a new one IMMEDIATELY after the projector has cooled down.  
( Follow carefully the instructions in the LAMP REPLACEMENT section of this manual.  )  Continuous
use of the lamp with the LAMP REPLACE INDICATOR lighted may increase the risk of lamp explosion.  
A Lamp may explode as a result of vibration, shock or degradation as a result of hours of use as its
lifetime draws to an end.  Risk of explosion may differ according to the environment or conditions in
which the projector and lamp are being used.
IF A LAMP EXPLODES, THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE TAKEN.
If a lamp explodes, disconnect the projector’s AC plug from the AC outlet immediately.  Contact an
authorized service station for a checkup of the unit and replacement of the lamp.  Additionally, check
carefully to ensure that there are no broken shards or pieces of glass around the projector or coming out
from the cooling air circulation holes.  Any broken shards found should be cleaned up carefully.  No one
should check the inside of the projector except those who are authorized trained technicians and who are
familiar with projector service.  Inappropriate attempts to service the unit by anyone, especially those who
are not appropriately trained to do so, may result in an accident or injury caused by pieces of broken
glass.  
LAMP HANDLING PRECAUTIONS
ORDER REPLACEMENT LAMP
Replacement Lamp can be ordered through your dealer.  When ordering a Projection Lamp, give the
following information to the dealer.
Model No. of your projector   : 38-MX3001-01
Replacement Lamp Type No. : 03-000749-01P
(Service Parts No. 610 307 1657) 
						

							48
APPENDIX
Check audio cable connection from audio input source.
Adjust audio source.
Press VOLUME (+) button.
Press MUTE button.
TROUBLESHOOTING
Before calling your dealer or service center for assistance, check matters below once again.
1. Make sure you have connected a projector to your computer or video equipment as described in section CONNECTING
PROJECTOR  on pages 12 ~ 15.
2. Check cable connection.  Verify that all computer, video and power cord are properly connected.
3. Verify that all power is switched on.
4. If a projector still does not produce an image, re-start your computer.
5. If an image still does not appear, unplug a projector from your computer and check your computer monitors
display.Problem may be with your graphics controller rather than with a projector.  (When you reconnect a projector, be
sure to turn a computer and monitor off before you power up a projector.  Power equipment back on in order of : Projector
and computer.)
6. If problem still exists, check following chart.
No power.Plug a projector into your AC outlet.
Turn MAIN ON/OFF switch to ON.
Press POWER ON/OFF switch to ON.
Make sure READY Indicator lights.
Wait 90 seconds after a projector is turned OFF when turning a projector back on.
NOTE :After pressing Power ON-OFF button to OFF, make sure a projector works as
follows:
1.  LAMP indicator lights bright and READY indicator turns off.
2. After 90 seconds, READY indicator lights green again and a projector may be
turned on by pressing Power ON-OFF button.
Check WARNING TEMP. and READY indicator. If both WARNING TEMP. and READY
indicator flashes, a projector can not be turned on.
(See TURNING ON/OFF PROJECTOR section on page 22.)
Check Projection Lamp.  (Refer to page 46.)
Image is out of
focus.Adjust focus of a projector.
Check Projection Lens to see if it needs cleaning.
NOTE : Moving a projector from a cool temperature location to a warm temperature location
may result in moisture condensation on Projection Lens.  In such an event, leave a
projector OFF and wait until condensation disappears.
Picture is Left/Right
reversed.Check Ceiling / Rear feature.  (See “SETTING” section on page 40.)
Problem:Try these Solutions
Picture is
Top/Bottom
reversed.Check Ceiling feature.  (See “SETTING” section on page 40.)
Some displays are
not seen during
Operation.Check Display feature.(See “SETTING” section on page 40.)
No image.Check connection between your computer or video equipment and a projector.
When turning a projector on, it takes about 30 seconds to display an image.
Check system that you select is corresponding with your computer or video equipment.
Make sure temperature is not out of Operating Temperature (5°C ~ 35°C).
No sound. 
						

							49
Check cable connection between a projector and your computer.
Check mouse setting on your computer.
Turn a projector on before turning on a computer.
APPENDIX
SERVICE
WARNING: High voltages are used to operate this projector. Do not attempt to open cabinet.
You can often correct operating problems yourself. If a projector fails to work properly, see TROUBLESHOOT-
ING section on page 48, 49. To correct failure, try Solutions.
If after following all operating instructions, you find that service is necessary, contact Christie Service Station or
store where you purchased unit.
Give model number and explain difficulty. We will advise you how to obtain service.
This symbol on the nameplate means the product is Listed by Underwriters
Laboratories Inc.  It is designed and manufactured to meet rigid U.L. safety
standards against risk of fire, casualty and electrical hazards.
The CE Mark is a Directive conformity mark of the European Community (EC).
Remote Control Unit
does not work.Check batteries.
Check ALL-OFF switch on Remote Control Unit is set to “ON.”.
Make sure nothing is between Infrared Remote Receiver and Remote Control Unit.
Make sure you are not too far from a projector when using Remote Control Unit.
Maximum operating range is 16.4’ (5m).
Check transmitted signal mode from Remote Control Unit.
(See “SETTING” section on page 40.)
Problem:Try these Solutions
Wireless Mouse
function does not
work. 
						

							50
APPENDIX
User’s Manual
AC Power Cord
Wireless/Wired Remote Control Transmitter and Batteries
Remote Control Cable
VGA Cable and DVI Cable
MAC/VGA Adapter and DVI/VGA Adapter
3 Types Control Cable (For PS/2, Serial and ADB port) 
6 Types Light-Block Sheet (For option lens)
Lens Attachment (For option lens)
Protective Dust Cover
TECHNICAL SPECIFICATIONS
1.8 TFT Active Matrix type, 3 panels
Multi-media Projector
81.7 lbs (37 kg)
22.9 x 10 x 30.9 (581 mm x 252 mm x 783 mm) 
1600 x 1200 dots
5,760,000 (1600 x 1200 x 3 panels)
PAL, SECAM, NTSC, NTSC4.43, PAL-M and PAL-N
Up, Down, Left and Right
1100 TV lines (HDTV)
Projector Type
Net Weight
Dimensions (W x H x D)
Panel Resolution
Number of Pixels
Color System
Scanning Frequency
Horizontal Resolution
LCD Panel System
100 watt type x 4Projection Lamp
480i, 480p, 575i, 575p, 720p, 1035i, 1080i-50 and 1080i-60High Definition TV Signal
H-sync. 15 ~ 120 KHz, V-sync. 50 ~ 120 Hz
Motorized Lens Shift
DVI-I Terminal (Digital/Analog), RCA Type (Audio R and L)
and DIN 8-pin (Control port)Input 1 Jacks
BNC Type x 5 (R/Pr, G/Y, B/Pb, H/HV and V), RCA Type (Audio R and L)
and DIN 8-pin (Control port)Input 2 Jacks
BNC Type x 2 (VIDEO/Y, C), RCA Type (Audio R and L)
and DIN 4-pin (S-Video)Input 3 Jacks
HDB 15-pin Terminal (Analog), RCA Type (Audio R and L)
and DIN 8-pin (Control port)Input 4 Jacks
Specifications are subject to change without notice.
LCD panels are manufactured to the highest possible standards. At least 99.99% of the pixels are effective,
however a tiny fraction of the pixels (0.01% or less) may be ineffective by the characteristics of the LCD
panels.
Accessories
INT. SP. Stereo (R and L), 3 watt RMS (T.H.D. 10%)
41 ˚F ~ 95 ˚F (5 ˚C ~ 35 ˚C)
14 ˚F ~ 140 ˚F (-10 ˚C ~ 60 ˚C)
Built-in Speakers
Operating Temperature
Storage Temperature
0˚ to 5.7˚Feet Adjustment
Power Source : AA, UM3 or R06 Type x 2
Operating Range : 16.4’ (5m) / ±30˚
Dimensions : 2.2” x 1.3” x 7.6” (55mm x 34mm x 192mm)
Net Weight : 0.36 lbs (165 g) (including batteries)
Laser Pointer : Class 
IILaser  (Max. Output : 1mW / Wave length : 650±20nm)
Remote Control Transmitter
AC 100 ~120 V  (7.0 A  Max. Ampere), 50 / 60 Hz  (The U.S.A and Canada)
AC 200 ~ 240 V (3.5 A  Max. Ampere), 50 / 60 Hz  (Continental Europe)
Voltage and 
Power Consumption
Serial port in (DB 9), Serial port out (DB 9), USB port,
Audio Monitor out (RCA Type R and L) and Wired Remote Jack Other Jacks