Christie Digital Systems Lx1500 Users Manual

11

Input / Output Terminals and Jacks
e	R/C j ACK
  When using the wired remote control, connect the 
wired remote control to this jack with a remote 
control cable (not supplied).
r	USB CONNECTOR (Series B)
  Use this connector when controlling a computer 
with the remote control of the projector. Connect 
the USB terminal of your computer to this 
connector with the USB cable (not supplied).
i	S-VIDEO INPUT j ACK
  Connect the S-VIDEO output signal from video 
equipment to this jack (p.21).
q	SERIAL...

1

y	FOCUS buttons
 Adjust the focus.  (p.27)
q	ZOOM buttons
 Zoom in and out the images.   (p.27)
t	ON/STAND-By button
 Turn the projector on or off.  (p.24)
i	INPUT 1/ button
   Select an input source either INPUT 1 or INPUT 2.  
  (pp.30-32)
r	AUTO PC AD j . button
 Automatically adjusts the computer image to its optimum setting.  (p.27)
o	INPUT 3/4 button
  Select an input source either INPUT 3 or INPUT 4. 
  (p.30)
e	  POINT button
  -  Select an item or adjust the value in  the On-...

13

Indicators
READY
LAMP
LAMP REPLACE
WARNINGTEMP.
WARNINGTEMP.
READY
LAMPREPLACE
LAMP
READY
LAMP
LAMP REPLACE
WARNINGTEMP.
WARNINGTEMP.
READY
LAMPREPLACE
LAMP
Front Indicators
Rear Indicators
q
w
e
r
q
w
e
r
e	WARNING TEMP  . indicator
  This indicator flashes red when internal projector 
temperature is too high. (pp.61, 68-69)
r LAMP REPLACE indicator
  This LAMP REPLACE indicator lights orange when 
any of projection lamps is nearing its end, and 
flashes when any of them becomes out.  Check 
which...

Remote Control
Part Names and Functions
q
t
e
!0
i
!4
r
!5
!3
!1
w
y
u
o
!7
!2
!8
!6
!9
@0
e	LIGHT button
 Light the buttons on the remote control for about 10 
seconds.
r MENU button
 Open or close the On-Screen MENU.  (pp.25-26)
t POINT ed 7 8 buttons
   –  Select an item or adjust the value in The ON-SCREEN MENU.
   –Pan the image in DIGITAL ZOOM +/– mode. (p.39)
y LENS SHIFT button
  Select the LENS SHIFT function.  (p.27)
!5 FOCUS buttons
 Adjust the focus.  (p.28)
u ZOOM buttons
 Zoom in and out...

Remote Control Battery Installation
123
Open the battery 
compartment lid.
Install new batteries into 
the compartment.
Replace the 
compartment lid.
Two AA size batteriesFor correct polarity (+ and –), be sure battery terminals are in contact with pins in the compartment.
To insure safe operation, please observe the following precautions :
 ● Use two (2) AA or LR6 type alkaline batteries.
  ● Always replace batteries in sets.
  ● Do not use a new battery with a used battery.
  ● Avoid contact with...

16

The eight different remote control codes (Code 1–Code 8) are assigned to this pro\
jector. Switching the remote 
control codes prevents interference from other remote controls when several projectors or video equipment 
next to each other are operated at the same time. Change the remote control code for the projector first before 
changing that for the remote control. See “Remote control” in the Setting Menu on page 50.
1
2
Remote Control Code
Part Names and Functions
Check the Reset Switch to...

17

Installation
Lens Installation
Before setting up a projector, install Projection Lens on a Projector.
1.   Before installation, check where a projector is used and prepare a suitable lens. For the specifications of 
Projection Lens, refer to the manual attached separately or contact sales dealer where you purchased the 
projector.
2.  For installation, refer to the installation manual accompanying a Projector.
When setting a projector after lens installation, be sure to replace a Lens Cap to protect...

1

Picture Level and Pitch Adjustment
Installation
Picture tilt and projection angle can be adjusted with 
handles on both sides of a projector.  Projection angle 
can be adjusted to 5.7 degrees upward. 
1
2
3
LEVEL AND PITCH
ADJUST HANDLE
ADJUSTABLE
FEET
Height of front feet can be adjusted 
by turning handles.
Press the knob on the handle. The handle pops 
out.
Turn handles (right and left) until picture is 
projected on proper position. Rotate rear 
adjustable feet to stabilize  the projector on...

19

Terminals of Projector
This projector applies various input/output terminals and 4 terminal slots for expansion to tune to diversity 
of signals from computers and video equipment. 4-built-in Terminal Slots enable you to arrange desired 
combinations of input sources just by changing Terminal Boards.  For Terminal Boards, contact sales dealer 
where you purchased a projector.
Pull out  the terminal by holding handle.
Remove 2 Screws on a terminal.1
2
Tighten screws to secure the terminal.
Replace...

0

Installation
ANALOG
vGBRH/HVV
DIGITAL¢DVI-D)
INPUT 1
R/C JACKUSB
RESET
INPUT 2
INPUT 3
INPUT 4
SERIAL PORT IN
SERIAL PORT OUTS-VIDEO
VIDEO/YPb/CbPr/Cr
Connecting to Computer
VGA Cable 
Monitor Output 
Desktop type
Laptop type
Terminals of
a Projector
Monitor Output 
DVI Cable BNC Cable ✽
Monitor Output 
Unplug  the  power  cords  of  both  the 
projector  and  external  equipment  from 
the AC outlet before connecting cables.
Cables used for connection 
• VGA Cable (D-sub 15 pin) *
• DVI Cable...