Christie Digital Systems Lw40 Model 38-viv210-01 Users Manual

11
CONNECTING PROJECTOR
TERMINALS OF PROJECTOR
This projector applies various input/output terminals and 3 terminal slots for expansion to tune to diversity of signals from
computers and video equipment. 3-built-in Terminal Slots enable you to arrange desired combinations of input sources just
by changing Terminal Boards.  For Terminal Boards, contact sales dealer where you purchased a projector.
Screws
Guide
Socket
Plug
Figure shows HDB 15-PIN terminal (Optional parts).
Pull out terminal by holding...

12
CONNECTING PROJECTOR
CONTROL PORT
INPUT 1
R/C JACKUSB
RESET(MONO)(MONO)
AUDIO
INPUT 2 INPUT 3
SERIAL PORT INSERIAL PORT OUTAUDIO OUTRLL
RLANALOG RGB
This port is used to service
this projector.Connect an audio output
from computer to these
jacks. (Refer to P13.)
CONTROL PORT CONNECTORAUDIO INPUT JACKS
INPUT/OUTPUT TERMINALS AND JACKS
Connect computer output
(Analog HDB 15-pin type) to
this terminal.  
(Refer to P13.)
HDB 15-PIN INPUT  TERMINAL
Connect an external audio
amplifier to these jacks....

13
CONNECTING PROJECTOR
CONTROL PORT
INPUT 1
R/C JACKUSBRESET(MONO)(MONO)
AUDIO
INPUT 2 INPUT 3
SERIAL PORT INSERIAL PORT OUTAUDIO OUTRL
RLANALOG RGB
CONNECTING TO COMPUTER
IBM-compatible computers or Macintosh computers (VGA / SVGA / XGA / SXGA / WXGA / UXGA
VGA Cable 
Desktop type Laptop type
Audio Cable
(stereo) ✽
Audio Output
Audio InputAUDIO OUT
MAC/VGA ✽AdapterSet slide switches
following chart
below.
Cables used for connection(✽= Cables are not supplied with this projector.)
• VGA Cable (HDB 15...

14
ON -- OFF
MENUINPUT
SELECTLENS
SHIFT VOLUMEIMAGE FOCUSAUTO
PC ADJ.ZOOM
LAMP
REPLACEWARNING
TEMP.
READY
LAMP
Used to open or close
MENU operation. (P15,
16)
MENU BUTTON
IMAGE BUTTON
READY INDICATOR
SELECT BUTTON
POWER ON–OFF BUTTONINPUT BUTTONS
WARNING TEMP. INDICATOR
LAMP INDICATOR
POINT BUTTONS 
LAMP REPLACE INDICATOR
Used to select image
level.  (P25, 30)
Lights  green when a
projector is ready to be
turned on.  And it
flashes green in Power
Management mode.
(P34)
Becomes dim when a
projector is...

15
BEFORE OPERATION
HOW TO OPERATE ON-SCREEN MENU
FLOW OF ON-SCREEN MENU OPERATION
Display ON-SCREEN MENU
Press MENU button to display ON-SCREEN MENU (MENU
BAR).  A red frame is POINTER.
Move POINTER (red frame) to MENU ICON that you want to
select by pressing POINT RIGHT / LEFT buttons.
Adjust ITEM DATA by pressing POINT RIGHT / LEFT
buttons.
Refer to following pages for details of respective
adjustments.
Press POINT DOWN button and move POINTER (red frame
or red arrow) to ITEM that you want to adjust,...

16
MENU BAR
PC SYSTEM MENU
Used to select
computer system.
(Refer to P20)
IMAGE ADJUST MENU
Used to adjust
computer image. 
[Contrast/Brightness
/Color Temp.
/White Balance (R/G/B)
/Sharpness/Gamma
/Noise Reduction
/Progressive]
(Refer to P26)
SETTING MENU
Used to change
settings of projector
or reset Lamp
Replace Counter. 
(Refer to P33-36)
SOUND MENU
Used to adjust
sound [volume,
Bass or Treble],to select Built-in
SP On-Off and
Sound Mute. 
(Refer to P19)
IMAGE SELECT MENU
Used to select
image level...

17
BASIC OPERATION
TURNING ON PROJECTOR
TURNING OFF PROJECTOR
TURNING ON / OFF PROJECTOR 
Power off?
Message disappears after 4 seconds.
Connect a projectors AC Power Cord into a wall outlet and turn
MAIN ON / OFF SWITCH to ON. LAMP indicator lights RED,
and READY indicator lights GREEN.
Press POWER ON-OFF button on Top Control to ON. LAMP
indicator dims, and Cooling Fans start to operate. Preparation
Display appears on a screen and count-down starts.  Signal from
source appears after 30 seconds.
Current...

18
KEYSTONE ADJUSTMENT
1Select Keystone on SETTING menu. (Refer to page 33.)
Keystone dialog box appears.
2Correct keystone distortion by pressing POINT UP/DOWN
button(s).  Press POINT UP button to reduce upper part of
image, and press  POINT DOWN button to reduce lower part.  
Reduce upper width with POINT UP button.  Reduce lower width with POINT DOWN button.  
If a projected picture has keystone distortion, correct image with KEYSTONE adjustment.
ADJUSTING SCREEN
Message disappears after 4 seconds....

19
BASIC OPERATION
1
2
Press MENU button and ON-SCREEN MENU will appear.  Press
POINT LEFT/RIGHT buttons to move a red frame pointer to
SOUND Menu icon. 
Volume
Press VOLUME (+/–) button(s) on Top Control or on Remote Control
Unit to adjust volume.  Volume dialog box appears on screen for a few
seconds.
(+) button to increase volume, and (–) button for decreasing.
To increase volume, press POINT RIGHT button, and press POINT
LEFT button for decreasing. 
Press POINT LEFT/RIGHT button(s) to cut off sound....

20
SELECTING COMPUTER SYSTEM
SELECTING INPUT SOURCE
MENU OPERATION
DIRECT OPERATION
Press MENU button and ON-SCREEN MENU will appear.  Press
POINT LEFT/RIGHT buttons to select Input and press  SELECT
button.  
Another dialog box INPUT SELECT Menu will appear. 
Press POINT DOWN button and a red-arrow icon will appear.
Move arrow to INPUT source that you want to select, and then
press SELECT button.  
1
2
INPUT 1
INPUT 2
INPUT 3
Select INPUT source by pressing INPUT /button on Top
Control.
INPUT /...