Christie Digital Systems Ds+5k, Kc-8k, Dw3k-6k, Kc, Mirage S+2-4-8k, Dlv1400-dx, Matrix 4000 Users Manual

Appendix D: Throw Distance 
 
   User’s Manual     D-9 
 
  

Appendix D: Throw Distance 
D-10      User’s Manual 
  

Appendix E 
System Integration 
 
   User’s Manual     E-1 
The GPIO (General Purpose Input Output) connector located on the input panel provides a flexible 
method of interfacing a wide range of external I/O devices to the projector. There are 7 GIO pins 
available on the 9pin D-Sub GPIO connector, which are configurable via RS232 commands. The other 
two pins are reserved for ground and power – see table below for pin identification. 
 
GPIO Pins 
Pin #  Signal 
1  + 12V (200mA) 
2 GPIO 1 
3 GPIO 2 
4...

Appendix E: System Integration 
E-2      User’s Manual 
 
Query Command 
(GIO?)  Request the state and configuration of all pins 
(GIO! “HHLLHLH” “OOIOOOI”)   Reply of pin state and configuration 
(GIO? C2)  Request configuration for pin #2 
(GIO! C2 O)  Reply with pin #2 configuration as output 
(GIO? 2)  Request the state of pin #2 
(GIO! H)  Reply with pin #2 state as high 
 
Real Time Event 
Use the serial command RTE to specify an action that is initiated at a particular time or based 
on an...

Appendix F 
Optional Input Modules 
 
   User’s Manual     F-1 
There are many optional input modules and accessories currently available for this 
projector. Contact your dealer for a complete and up-to-date listing. 
 
The RGB500 Input Module may be installed in this projector, a Marquee Signal 
Switcher, or a Marquee Case/Power Supply. The module receives analog RGB input 
signals from computers or other RGB source devices. 
 
RGB500 Features 
◊ Accepts 3, 4, or 5 wire RGB video (sync-on-green,...

Appendix F: Optional Input Modules 
F-2      User’s Manual 
 
The RGB400 ALT Input Module may be installed in this projector, a Marquee Signal 
Switcher, or a Marquee Case/Power Supply. The module receives analog RGB input 
signals from computers or other RGB source devices. Video inputs are 75
Ω 
terminated. Video outputs provide buffered loop-through to another display device. 
 
RGB400ALT Features 
◊ Accepts 3, 4, or 5 wire RGB video (sync-on-green, composite sync, or 
separate horizontal and vertical...

Appendix F: Optional Input Modules 
 
   User’s Manual     F-3  
 
This module can display digital video input signals conforming to the DVI (Digital 
Visual Interface) single-channel standard. 
 
Features 
◊ Supports Digital Visual Interface (DVI) single-channel  
◊ Supports VESA Extended Display Identification Data (EDID)  
◊ Provides an active-loop-through using a DVI connector (conforming to 
the DVI Specification) 
 
The module accepts a serial digital 4:2:2 component video signal (YCbCr) via a...

 
Index 
 
 User’s Manual 
  
3 
3D Simulation, 3-33 
3D Stereo Sync, 3-34 
A 
Ambient Lighting, 2-5 
Anamorphic, 3-22 
Arrow Keys, 3-9 
Auto Input Level, 3-29 
Auto Key, 3-5 
Auto Setup, 3-5 
AutoSource Checkbox, 3-19 
B 
Backlight, 3-41 
Bad Sync, 3-69 
Baud Rate, 2-17, 3-38 
Blacklevels and Drives, 3-29 
Blanking, 3-24 
Brightness Key, 3-7 
Brightness Uniformity 
Canceling, 3-63 
Definition, 3-60 
Prerequisites, 3-60 
Procedure, 3-60 
Submenu, 3-42 
Broadcast Key, 3-41 
Broadcasting, 3-9 
Built-in...

Appendix F: Optional Input Modules 
 
    User’s Manual 
D 
Dark Interval, 3-34 
Date and Time 
Setting, 3-36 
Decoder AGC 
Enabling, 3-27 
Decoder Luma Delay, 3-28 
Detail 
Threshold, 3-35 
Diagnostics and Calibration, Submenu, 
3-47 
Display 
Channel List, 3-37 
Error Messages, 3-37 
Slidebars, 3-37 
DVI, 2-14 
E 
Edge Blending, 3-43 
Description, 3-64 
How Blends are Used, 3-64 
Main functions, 3-64 
Procedure, 3-66 
Enter Key, 3-9 
Error Messages 
Bad Sync, 3-69 
H-Sync or V-Sync, 3-70 
No Signal,...