Cetme SEMI-AUTO RIFLE, CAL. .308 NATO Instruction Manual

							CETME 
SEMI-AUTO RIFLE,
CAL. .308 NATO
INSTRUCTION
MANUAL 
						

							CETME Semi-Automatic Rifle
3
OPERATIONLoading MagazineThe magazine is loaded by inserting the cartridge in the
magazine and pressing it under the lip with the thumb.  Inserting and removing magazineAlways put the Cetme safety lever in “S” (safe) mode.
Insert the magazine into the magazine well from below until
the magazine catch engages.  Remove the magazine by
pressing the magazine release button.Safety selectorThe left side of the grip assembly has a “S” (safe) and “F”
(fire) safety lever.  The safety position can also be seen on
the right side of the grip assembly.  
Always keep your Cetme in the “S” (safe) mode by setting
the safety lever to “S”.  The trigger can not be pulled while it
is on safe.  Never point your rifle at anyone even when it is
on safe.  To fire your rifle, move the safety lever to the “F”
(fire) position and squeeze the trigger.  Always be sure of
your target and the area beyond it.Loading Put your Cetme in the “F” (fire) mode position.  Pull the
cocking lever rearward and up, this engages it in the recess
of the cocking lever housing.  Place selector on “S” (safe)
and insert the loaded magazine and allow the cocking lever
to slide forward.  The rifle is now loaded.  (Note:  In order to
cock the Cetme rifle the rifle must be off safe.)CleaningPut your Cetme rifle in the “S” (safe) mode.  Remove the
magazine and unload the chamber.  Pull the cocking lever
INTRODUCTIONThe Cetme Rifle is built using genuine Cetme parts and a
U.S. manufactured made receiver.  The Cetme conforms to
B.A.T.F. requirements.  It is semi-automatic only.
The use of reloaded, re-manufactured, hand loaded, orother nonstandard ammunition may result in damage to theuser or rifle.The manufacturer and importer can not accept responsibili
-
ty for malfunctions resulting from the use of nonstandarddefective ammunition.
CETME Semi-Automatic Rifle
2 
						

							CETME Semi-Automatic Rifle
with a commercial rust preventative.Elevation and Windage adjustmentThe rear sight has 4 settings: 100 meters (open sight), 200,
300 and 400 meters (peep sights).  To set the sights, set
the 100 meter sight and shoot a group at 100 meters.
Adjust the front post up or down until the desired point of
impact is gained.  The front sight is also adjustable for
windage. To make the rifle shoot to the right adjust the sight
post to the left of center.  To shoot to the left adjust the sight
screw to the right of center.  (The small screw on the front
of the sight base must be loosened before adjusting the
front sight post.  Tighten the screw before firing to ensure
the front sight does not move after it is adjusted)SAFETYSafety FirstFirearms can be dangerous and can cause serious injury or
death.  Proper and safe firearms handling is the responsibil-
ity of anyone who touches or uses a firearm.  Safety has to
be the primary consideration of anyone using a
firearm.When purchasing a firearm, you assume responsi-
bility for its safe use, storage and transportation.  It is partic-
ularly critical that firearms be kept from unauthorized use,
and this includes children.  Your responsibility also includes,
but is not limited to, the need to protect yourself and others
from injury resulting from the misuse or abuse of a firearm.
Treat firearms as though they are loaded
Always be aware of where the muzzle is pointed.
Before shooting, make certain the barrel has no 
obstructions.
Do not allow a firearm or ammunition to be left 
5
backwards and verify that the chamber is empty and
release the cocking lever.  Remove the butt stock which is
held by two pins.  Remove the grip assembly and retract
the bolt assembly and remove it from the receiver.  Remove
the handguard.  Clean the bore with a brush followed by
patches and a commercial gun cleaner.
To strip the bolt assembly remove the bolt head from the
bolt assembly by turning it 90 degrees to the right and turn
the locking piece until lug can be removed from the bolt
head carrier.  Clean parts using a cloth saturated with a
commercial gun cleaner and relubricate lightly.
To reassemble the bolt reverse the above procedure and
push the head with the slanted surface under the tip of the
locking lever.  Be sure that locking rollers are in place in the
bolt head when reassembling. To strip the grip assembly
with the trigger mechanism, set the safety point vertically
up,  then pull the lever out and remove the grip assembly.
Reassembly
Reattach the handguard and insert the assembled bolt with
the recoil spring into the receiver.  Be sure that both locking
rollers are recessed into the bolt head.
Attach the grip assembly and set the safety lever to “S”.
Slide the butt stock onto the receiver and insert the locking
pins.  It is always recommended to have your firearm peri-
odically inspected by a qualified gunsmith.
On the Cetme rifle head space is determined by measuring
the gap between the bolt head and bolt head carrier.  This
measurement should be between .005” and .019”.  If it is
not, your rifle should be checked by a qualified gunsmith.
Once the rifle has been assembled, wipe the blued surfaces4
CETME Semi-Automatic Rifle 
						

							physical injury.  Have adequate ventilation at all times.
Wash hands thoroughly after exposure.
Store your firearm unloaded and in an area which is
secure from unauthorized access.  Furthermore, store
ammunition separately, and in an area secure from
unauthorized access.
7
CETME Semi-Automatic Rifle
unattended. Secure both the firearm and ammunition
from access by unauthorized people including 
children.
When shooting, always be certain that the area 
beyond the target, including the backstop, is clear 
and safe. Ensure that shots fired present no safety 
hazards for yourself or others. 
Always understand the proper operation of your 
firearm, and never allow the firearm to be used by 
anyone who does not understand how to use the 
firearm properly and safely. 
Always use both ear and eye protection when shoot-
ing. 
Always use factory loaded ammunition designed for 
and intended to be used in the firearm you are 
shooting. It must be the proper caliber and type for 
your firearm. 
Never pass a firearm to another person unless the 
action is open and the firearm is in an unloaded and 
safe condition. 
Never put your finger into the trigger guard until you 
are ready to shoot. 
When not using the firearm, ensure that it is 
unloaded. 
Carry your firearm in a way that will preclude acci-
dental injury to yourself or others in the event you 
should  stumble, fall or drop the firearm.
Safety Warning: Discharging firearms in poorly ventilated areas, clean-
ing firearms or handling ammunition may result in
exposure to lead and other substances known to cause
birth defects, reproductive harm and other serious6
CETME Semi-Automatic Rifle
Technical Specifications:Caliber: .308 Win.  
Rear Sight: Aperture   
Front sight: Hooded post  
Barrel length: 19 1/4”  
Overall length: 40 1/2”  
Weight: 9.56 lbs. without magazine 
						

							Distributed by
:
Century International Arms, Inc.
236 Bryce Blvd.
Fairfax, Vermont 05454
Tel: 1-800-527-1252
WWW.CENTURYARMS.COM