CCRadio Instruction Manual

							Page 11 
Please read this entire page carefully before you start.The correct
time must be set with the radio off. If you do not finish setting the clock or
alarm in 15 seconds you will have to start over.
1)  Press the 
Band/Time Setbutton. The hour digit will flash.
2)  Using the Up/Down tuning button, select the appropriate
hour digit.
3)  Press the 
Band/Time Setbutton again to select the minute digit. Use
the Up/Down buttons to adjust the minute to the appropriate time.
4)  You must press the 
Band/Time Setbutton again to complete the time
setting. This also sets the seconds to “00”.
SETTINGTHECLOCK
SETTINGTHEALARM
There are two different alarm modes on the CCRadio. You can choose
to wake up to the radio or to a tone. You can set the alarm with the radio
on or off.
To set the type of alarm:
Press the 
Alarmbutton on top of the radio until you
see this symbol on the display to wake with the radio.
When the alarm goes off the radio will play the last station selected at
the same volume level last set.
Press the 
Alarmbutton until you see this symbol to wake with
a multi level tone.
Press the 
Alarmbutton until both symbols disappear to shut off the
alarm function.
To set the time for the alarm to go off:
1)  Press the 
Alarmbutton, the hour digit and alarm symbol will flash.
2)  Using the Up/Down button, select the appropriate hour.
3)  Press the 
Band/Time Setbutton. Use the Up/Down
buttons to adjust the minute to the appropriate time.
4)  You must press the 
Band/Time Setbutton again to complete the
alarm setting.
You can also set the alarm time immediately after selecting the radio or
buzzer alarm as describe above if you are a whiz.     
						

							Page 12
NOTESONTHEALARM:
To stop the alarm from going off every day press the Alarmbutton on
top of the radio until both symbols disappear.
Once the alarm is set, it will automatically go off the next day at the same
time. Use the 
POWERbutton to shut off the alarm until the next day.
If the radio alarm is selected, turn the radio to your favorite station before
setting the alarm. When the alarm activates the radio will play the last sta-
tion listened to.
The tone alarm is called HWS or Humane Wake (if that is possible) System.
The alarm tone beep will increase in volume every 15 seconds for one
minute followed by one minute of silence before repeating the cycle.
The alarm system will sound for one hour unless turned off by pressing the
POWERbutton.
When the alarm is sounding, if you press any button except the POWER
button the alarm will temporarily stop for five minutes. The little Z’s and
alarm symbol will flash on the display while the radio is in snooze mode.
To shut off the alarm and snooze feature press the 
POWER button.
SNOOZEFEATURE:
SLEEPTIMERFEATURE:
Your CCRadio is equipped with a Sleep Timer that enables the radio to
continue playing for up to 90 minutes after activation, then shuts the radio
off. Selectable times are 90, 60, 30 and 15 minutes.
To utilize this feature, have the radio on and tuned to the station
you want to listen to, then press the button that has the pictogram
of a person in bed.
*You can also activate the sleep timer and turn on the radio at the same
time by pressing the sleep timer button. This button is located just under
the Band/Time Set button. When the button is pressed, the number 90 will
appear in the upper right hand corner of the LCD display panel. Pushing
the button repeatedly will reduce the time down in steps, showing times of
60, 30, and 15 minutes. If you miss the time you want, merely continue
pressing the button until the desired time shows on the display. Release
the button. Now the pictogram of the person in bed will appear on the dis-
play. The radio will then shut off after the set amount of time. To deactivate
the Sleep Timer, simply shut the radio off using the power switch.     
						

							Page 13 
RADIOOPERATION
The CCRadio features four bands: AM / FM / TV 2-13 and Weather.
M
ANUALTUNING:
1)  Press the 
POWERbutton to turn on the radio.
2)  Select the band by pressing the 
BANDbutton.
3)  A single press of the Up or Down tuning button will
change the frequency up or down for AM and FM bands,
and
channel up or down for weather and TV bands.
Each press of tuning Up and Down buttons will change the frequency by
10 KHz in AM mode and 100 KHz in FM mode.
S
CANTUNING:
Same as above except press and hold down tuning Up or
Down button for more than .5 second. The radio will scan and
stop automatically when it finds an active station. The Scan Tuning will
not work on the weather band.
R
OTARYTUNING:
Rotating the tuning knob will change AM/FM by frequency and the
weather/TV bands by channel.
M
EMORYTUNING:
You can store up to five memory stations in
each of the four bands.
1)  Tune to the station or channel you want to memorize.
2)  Press and Hold any memory button for two seconds to memorize the
station or channel.
The display will show the memory number and beep.
To recall the memory station select the correct band and press the
memory number. The radio will instantly tune to the station stored in
memory.    
						

							Page 14
The unique WXALERTmode on the CCRadio will alert you to special
weather related emergencies. During an emergency or weather related
hazard, NOAA issues an emergency tone that will set off an audible
and/or visual alarm on the radio.
NOTE: Hazard warnings are not available in all areas.
There are seven standard NOAA weather channels used in the US and
Canada. This radio receives broadcasts up to 50 miles from transmitting
stations.
1)  To listen to the standard NOAA weather channels, turn the radio on,
press the 
BANDbutton until WX shows up on the display. The tele-
scopic whip antenna may need to be in the up position to receive a
station clearly.
2)  You will see the channel number of the weather station. Pressing the
tuning up or down buttons will toggle you through the seven pro-
grammed channels. There should be one or more weather service
stations broadcasting in your local area. You will hear a report that is
updated usually once or more per day for your area. If there is a
severe weather or weather related emergency NOAA will update the
weather broadcast more frequently. If there is a weather emergency
the NOAA will issue an alert tone.
After locating and tuning in your weather station the radio can now be
placed into 
WXALERTmode. The WXALERTmode enables you to lis-
ten to your favorite AM or FM station or turn the radio off, and still
receive an alert signal warning you of a special emergency. There are
two active 
WXALERTmodes on the CCRadio:
SETTINGTHEWEATHERALERT
1)  To place the radio in 
WXALERTmode, press the ALERTbutton for
two seconds: You will hear an audible beep and see the word
ALERTappear on the display. This is WXALERTmode with flashing
light only (no Alarm). If there is a weather related emergency, the
radio will automatically alert you with a small flashing light near the
top of the radio. The Alert light continues to flash until any button is
pushed.
2) 
To access the second mode, (WXALERT with flashing light and tone)
Press the ALERTbutton again for two seconds until the red light
WEATHERALERTSYSTEM 
						

							near the top radio comes on continuously:WXALERTwith Alarm
and flashing light will be active. Display shows 
ALERT and red light
near the top of the radio. In this mode, if the NOAA alert tone is
issued, the red light on the top of the radio flashes and a siren turns
on for 1 minute. To cancel the 
WXALERT, press any button on the
radio.
SPECIAL NOTE: If you have the headphones plugged in and a weather
alert is issued, the audio to the headphones will be cut-off and the siren
will sound through the radio’s speaker.
3) Press 
ALERTagain for two seconds:WXALERTgoes off and is
inactive.
ALERTwill disappear from the display.
In either active 
WXALERTmode, the weather receiver stays on and lis-
tens for an emergency tone issued from NOAA in case of emergency.
You may get a periodic test tone from the NOAA that will cause a false
alarm on your 
WXALERT. This tone is only a test and will happen peri-
odically whenever the agency decides to test their emergency alert sys-
tem. Simply pressing any button on the receiver will shut the alert tone
off.
After an alert has been issued, the 
WXALERTlight and/or siren will stay
on for one minute or until you turn it off by pressing any button.
DISPLAYLIGHT
DISPLAYLIGHT ONAC POWER:
The display light will always be on unless you turn it off. The spe-
cial green LED bulbs last about 100,000 hours and use very little
electrical energy. If you want to turn off the display light, press the
Light button.
D
ISPLAYLIGHT ONBATTERIES:
When batteries are used the display light can be turned on by
pressing the light button. The display light automatically goes off
two minutes after radio operations are completed.
Page 15    
						

							LOCKSWITCH
The Lock switch can be used when transporting the
radio to prevent turning it on. When the switch is
pushed up you will see the Lock symbol appear
on the display. It can also be used to disable all func-
tions of the radio when it is turned on. Push the Lock
down to release the lock switch.
HEADPHONEJACK
You can use a stereo or mono headphone with a 3.5 mm plug. When
you insert the headphone plug, the speaker is disconnected. This radio
will not receive a stereo FM station in stereo through the headphones.
This provides clearer FM reception with less noise when compared to
stereo reception.
RESETBUTTON
Once in awhile glitches may occur on any portable digital radio. This can
be caused by static electricity, unusual key strokes or a power disrup-
tion. If this happens, use the end of a paper clip or ball point pen and
push it into the hole briefly to reset the radio.You will lose the clock
time, and all the stations stored in memory when the radio is reset.
Lock Switch
Headphone
Jack
Reset Button
Bottom View of CCRadio
Page 16    
						

							Page 17 
SPECIFICATIONS
FREQUENCYCOVERAGE
FM Band: 87.5 - 108 MHz Mono Only
AM Band: 520 - 1710 KHz
TV Band: Channels 2-13 Audio Only
WEATHERBAND
Channel 1: 162.400 MHz Channel 5: 162.500 MHz
Channel 2: 162.425 MHz Channel 6: 162.525 MHz
Channel 3: 162.450 MHz Channel 7: 162.550 MHz
Channel 4: 162.475 MHz
ROTARYTUNINGKNOBRESOLUTION
AM - 1 KHz TV  - 1 Channel
FM - 50 KHz WX - 1 Channel
POWERSOURCE
AC 120 Volts 60Hz
Batteries: (4) “D” size
POWERCONSUMPTION
AC Power: 8 Watts
Battery Power: 40-50 Ma DC
AUDIO
10% THD at output power @ 1.8 Watt AC typical
@ .9 Watt Battery
Speaker: 5”, 4 Ohm, 6 Watts
ANTENNA
FM, TV and Weather Band: Telescopic antenna
AM Band: 1) Built-in Ferrite Bar -  7/16” dia x 8” long (200 mm)
2) External AM antenna terminals are connected to    
inductive loop wound around internal ferrite antenna.
DIMENSIONS
11” wide x 6-1/2” high x 4” deep, (at the base) 
WEIGHT
Approximately 3.8 pounds without batteries
Note: Specifications are subject to change without notice. 
						

							Page 18
AM TUNING& LISTENINGTIPS
The CCRadio is made for distant or weak AM signal listening. Daytime
reception is limited to about 300 miles maximum because you can only
receive the signal direct from the transmitter site. You may receive AM
stations thousands of miles away at dawn, dusk and at night, depending
on the time of year and atmospheric conditions. The ionosphere is a
layer of ions above the earth. At night it slows and congeals into a giant
mirror and can reflect radio waves back to the earth; allowing you to
receive signals much farther away than during the day.
Distant listening is called DXing. One club that is devoted to DXing is
National Radio Club at: PO Box 164, Mannsville, NY 13661-0164. They
maintain a website at:
http://www.nrcdxas.org
Top View CCRadio
Left Side Rear View 
Most portable radios including the CCRadio have an internal AM anten-
na. Best performance is achieved when the radio is swiveled on its base
for maximum signal pickup from the transmitting tower. This same tech-
nique can be used to help nullify unwanted signals or radio noise.
Experimentation is the best way to see how it works for you.
The CCRadio has two external antenna terminals for AM. If your recep-
tion is better outside, for a quick and easy antenna use 50’ of insulated
wire attached to one terminal and a ground to the other terminal.Safety
directions and precautions from your antenna supplier should be
followed to prevent injury from lightning or any accident.
External Antenna
Terminals for AM   
						

							RADIONOISE TROUBLESHOOTING
Annoying buzzes are many times
transmitted through an AM radio.
Here is a check-off list of the most
likely causes:
 Dimmer switch.
 Fluorescent light.
 “Touch lamp” type light fixture
(even when turned off).
 Automatic on and off night lights.
 Outdoor yard lights which come on
automatically.
 Electronic bug and pest controllers.
 A light bulb that is about to burn out.
 A faulty electrical switch of any kind.
 A nearby television set.
 A store that has a fluorescent light
or a public recreation room that has
fluorescent lights located near you.
 Blinking bulbs of all kinds such as
Christmas tree lights.
 If you live in an apartment a
neighbor’s dimmer switch could be
the culprit.
 Scanners of all types.
 Dirty insulators on a nearby power
pole allowing arcing.
 Electric blanket.
 Smoke detectors that run from AC
current (battery operated is OK).
AM RADIONOISEPROBLEMS AND
POSSIBLESOLUTIONS
It is best to eliminate the interfer-
ence at its source. Here’s a list of
possible solutions:
 The most obvious is to turn off the
offending device.
 Try a battery operated radio to see if
the interference is coming in from
the AC 120v line, through the air, or
both.
 Turn off the circuit breakers to see if
the noise stops. If it does, then you
know it is something in your house.
Turn off one circuit at a time to iso-
late where the noise is coming from.
 Use a battery operated radio as a
direction finder. Turn the radio until
the loudest noise is heard and the
front and back of the radio will point
to the noise origin.
 Carry a radio around the neighbor-
hood and see if you can find the
origin of the noise. Ask other neigh-
bors if they have the same problem.
 If a power pole is suspected, call
the utility company and they will 
check the area and possibly wash
the insulators. Dirty power pole insu-
lators are sometimes a cause of
difficult-to-find radio interference.
 If you have a hum in your receiver
from AC line noise sometimes
grounding the radio can reduce the
hum greatly. Finding a good earth
ground may be difficult.
Page 19  
						

							CityFrequencyDateTime
PERSONALSTATIONLOG
Station
Call Letters
Page 20
Please feel free to copy this page.