Catena Lawn Mower CAT/E1339P Instructions Manual

							8FR
7.1 INTERRUPTEUR À DOUBLE ACTION
Le moteur est commandé par un inter-
rupteur à double action, afin de préve-
nir un démarrage accidentel. 
Pour démarrer, presser le bouton (2) et
tirer le levier (1). 
Le moteur s’arrête automatiquement
dès que le levier (1) est relâché.
7.2 REGLAGE DE COUPE
Le réglage de la hauteur de coupe est
obtenue en positionnant les roues
dans le trou correspondant, en serrant
à fond le pivot (1) à l’aide de la clé (2)
fournie. 
Toutes les roues doivent être montées
à la même hauteur. 
LA LAME NE DOIT PAS ÊTRE
ENGAGÉE PENDANT L’OPÉRATION
DE RÉGLAGE.
7. DESCRIPTION DES COMMANDES
12
STOP
START
121
2 
						

							9FR
8.1 ACCROCHAGE DU BAC
Soulever le pare-pierres et accrocher correctement le bac
(1), comme indiqué sur la figure.
8.2 DEMARRAGE
Accrocher correctement le câble de rallonge
comme indiqué.
Pour le démarrage, appuyer sur le bouton de blo-
cage (2) et tirer sur le levier (1) de linterrupteur.
8.3 CONSEILS POUR UNE BONNE TONTE
Pendant la tonte, faire en sorte que le câble élec-
trique se trouve toujours derrière soi et dans une
partie du terrain déjà tondue.
La pelouse aura un plus bel aspect si elle est tou-
jours tondue à la même hauteur et dans les deux
sens perpendiculaires alternativement.
NOTE IMPORTANTE- Si le moteur s’arrête à
cause de surchauffe durant son fonctionnement,
il est nécessaire d’attendre au moins 5 minutes
avant un nouvel essai.
8.4 FIN DU TRAVAIL
Lorsque le travail est terminé, relâcher le
levier (1). 
Débrancher D’ABORD la rallonge électrique
de la prise de secteur (2) et ENSUITE du côté
du contacteur de la tondeuse (3). 
ATTENDRE L’ARRÊT DE LA LAME avant d’ef-
fectuer toute intervention sur la tondeuse.
8. TONTE DE L’HERBE
1
2
1
32
2
1
1  
						

							10FR
IMPORTANT – Il est indispensable d’effectuer des opérations d’entretien régulières et
soignées pour maintenir pendant longtemps les niveaux de sécurité et les perfor-
mances originelles de la machine.
Garder la tondeuse dans un endroit sec.
1) Porter des gants de travail résistants avant deffectuer toute intervention de nettoyage,
dentretien ou bien de réglage sur la machine.
2) Après chaque coupe, enlever les détritus de gazon et la boue qui se sont accumulés à
l’intérieur du châssis, pour éviter qu’en séchant ils ne rendent le prochain démarrage
particulièrement difficile.
9.1 DEMONTAGE ET MONTAGE DE LA LAME
Toutes les opérations sur la lame doivent
être exécutées dans un centre spécialisé.
Remarque pour le centre spécialisé:
Remonter la lame (2) en respectant l’ordre
illustré sur la figure ; veiller à serrer la vis
centrale (1) avec une clé dynamométrique
tarée à 16 - 20 Nm.
9.2 NETTOYAGE DE LA TONDEUSE
Ne pas l’asperger au jet d’eau et éviter de
mouiller le moteur et les composants élec-
triques.
Ne pas utiliser de solvants ou de liquides
abrasifs pour le nettoyage du carter de
coupe.
9. MAINTENANCE
1
2 
						

							11FR
10. DIAGNOSTIC
La tondeuse électrique ne
fonctionne pas
La tondeuse électrique fait
disjoncter mon habitation
L’herbe coupée n’est plus
rejetée dans le panier
L’herbe est difficilement
coupée– Le courant arrive-t-il à la ton-
deuse?
– L’ampérage de la prise est-il
suffisant?
– D’autres appareils fonction-
nent-ils en même temps?
– Y-a-t-il une odeur de brûlé ou
de la fumée?
– La lame a-t-elle reçu un coup?
– Le carter de la tondeuse est-il
propre ?
– La lame est-elle en bon état?– Vérifier votre branchement
électrique.
– Contrôler le fusible ou contac-
ter le Service Après Vente de
votre magasin.
– Essayer une prise à ampérage
suffisant.
– Ne pas brancher plusieurs
appareils sur la même prise en
même temps.
– Débrancher immédiatement
votre tondeuse et contacter le
Service Après Vente de votre
magasin.
– Si oui, affûter la lame ou la
remplacer. Vérifier les ailettes
qui orientent l’herbe vers le
panier.
– Si non, nettoyer le carter afin
de faciliter l’évacuation de
l’herbe vers le panier.
– Si oui, affûter la lame ou la
remplacer.
Quels problèmes? Les constats à faire: Nous vous conseillons de: 
						

							1EN
First of all we would like to thank you 
for being among our customers. 
We have prepared everything needed to offer 
you an efficient product conforming with 
the directives currently in force.
This manual will help you assemble and 
use the machine you have just bought.
We are always at your disposal. 
						

							2EN
2) Avoid operating the equipment on wet grass or in the
rain.
3) Never go over the electric cable with the lawnmow-
er. While cutting, the cable should always be pulled
behind the lawnmower and always from the area of
grass already cut. Use the cable clamp as described in
this manual to prevent the cable from disconnecting by
accident. Ensure that it is properly inserted without
forcing into the power socket.
4) Never pull the lawnmower by its power cable or pull
the cable to remove the plug. Do not expose the cable
to sources of heat or let it come in contact with oil, sol-
vents or sharp objects.
5) Always be sure of your footing on slopes.
6) Walk, never run and do not allow yourself to be
pulled along by the lawnmower.
7) Mow across the face of slopes, never up and down.
8) Exercise extreme caution when changing direction
on slopes.
9) Do not mow on slopes that are too steep.
10) Exercise extreme caution when pulling the lawn-
mower towards you.
11) Stop the blade if the lawnmower has to be tilted for
transportation when crossing surfaces other than
grass, and when transporting the lawnmower to and
from the area to be mowed.
12) Never operate the lawnmower with defective
guards, or without safety devices, such as the stone-
guard and/or grass-catchers, in place.
13) On power-driven models, disengage the drive
clutch before starting the engine.
14) Start the engine carefully, following the instructions
and keeping feet well away from the blade. 
15) Do not tilt the lawnmower when switching on the
engine unless it is strictly necessary for start-up. In this
case, do not tilt it more than is strictly necessary and
only lift the part furthest away from the operator. Check
that both hands are positioned correctly before lower-
ing the lawnmower.
16) Do not put hands or feet near or under rotating
parts. Keep clear of the discharge opening at all times.
17) Never pick up or carry a lawnmower while the
engine is running.
18) Stop the engine and disconnect the power supply
cable:
– before carrying out any work underneath the cutting
deck or before unclogging the chute;
– before checking, cleaning or working on lawnmower;
– after striking a foreign object. Inspect the lawnmow-
er for damage and make repairs before restarting and
operating the lawnmower;
– if the lawnmower starts to vibrate abnormally, find
and remove the cause of the vibration immediately;
– whenever you leave the lawnmower unattended.
– when transporting the equipment.
19) Stop the engine:
– every time you remove or replace the grass-catcher.
– before adjusting the grass cutting height.
20) When mowing, always keep to a safe distance from
the rotating blade. This distance is the length of the
handle.
D) MAINTENANCE AND STORAGE
1) Keep all nuts, bolts and screws tight to be sure the
equipment is in safe working condition. Regular main-
tenance is essential for safety and performance.
2) To reduce the fire hazard, keep the lawnmower,
especially the engine, free of grass, leaves, or exces-1. SAFETY REGULATIONS
A) TRAINING
1) Read the instructions carefully. Get familiar with the
controls and the proper use of the equipment. Learn
how to stop the engine quickly.
2) Only use the lawnmower for the purpose for which it
was designed, i.e. for cutting and collecting grass. Any
other use can be hazardous, causing injury or damage
to people and/or property.
3) Never allow children or people unfamiliar with these
instructions to use the lawnmower. Local regulations
may restrict the age of the operator.
4) Never use the lawnmower:
– When people, especially children, or pets are nearby;
– If the operator has taken medicine or substances that
can affect his ability to react and concentrate.
5) Remember that the operator or user is responsible
for accidents or hazards occurring to other people or
their property.
B) PREPARATION
1) While mowing, always wear sturdy footwear and
long trousers. Do not operate the equipment when
barefoot or wearing open sandals.
2) Thoroughly inspect the area where the equipment is
to be used and remove all objects which may be
thrown by the machine or damage the cutter assembly
and the engine (stones, sticks, metal wire, bones, etc.).
3) Before use, always inspect the machine, especially
the condition of the blades, and check that the screws
and cutting assembly are not worn or damaged.
Replace worn or damaged blades and screws in sets
to preserve balance.
4) Before mowing, attach the discharge opening
guards (grass-catcher or stone-guard).
5) WARNING: DANGER! Damp and electricity do not
go together:
– cables must be handled and wired when dry
– never allow contact between an electric socket or
cable with a wet area (puddles or damp grass);
– connections between cables and sockets must be of
the waterproof type. Only use extension cables with
moulded-on waterproof or approved sockets available
commercially.
– power the machine using a residual current device
(RCD Residual Current Device) with max. 30 mA trip-
ping current.
6) The power supply cables must not be of lower qual-
ity than the H05RN-F or H05VV-F type with minimum
cross-section size of 1.5 mm2 and max. 25 m long.
7) Attach the cable onto the cable clamp before start-
ing the machine.
8) The permanent wiring of any electrical device to the
mains must be carried out by a qualified electrician, in
accordance with electrical regulations in force.
Incorrect wiring may cause severe injury or death.
C) OPERATION 
1) Mow only in daylight or good artificial light. 
						

							3EN
sive grease. Do not leave containers with grass cut-
tings in rooms.
3) Check the stone-guard and grass-catcher frequent-
ly for wear and deterioration.
4) Periodically check the electric cables and replace
them if they are damaged or if the insulation has been
damaged. Never touch a badly insulated cable if it still
connected to the power supply. Remove the cable
from the socket before taking any action.
5) Wear strong work gloves when removing and
reassembling the blade.
6) Keep the blade balanced during sharpening. All
operations on the blade (dismantling, sharpening, bal-
ancing, remounting and/or replacing) require a certain
familiarity and special tools. For safety reasons, these
jobs are best carried out at a specialized centre.
7) For reasons of safety, do not use the equipment with
worn cables or damaged parts. Parts are to be replac-
ed and not repaired. Use genuine spare parts (blades
max 20°
D6D5
B2A4A1
C7-9C15B6-8B4
C18C16
should always bear the symbol  ). Parts that are not
of the same quality can damage the equipment and be
dangerous for your safety.
E) TRANSPORTATION AND HANDLING
1) Whenever the machine is to be handled, raised,
transported or tilted you must:
– 
wear strong working gloves;
– 
grasp the machine at the points that offer a safe grip,
taking account of the weight and its distribution.
– 
use an appropriate number of people for the weight
of the machine and the characteristics of the vehicle or
the place where it has to be placed or collected.
D7     
						

							4EN
2. SAFETY REQUIREMENTS
Your lawnmower should be used with due care and attention.  
Symbols have therefore been placed on various parts of the machine to remind you of the
main precautions to be taken. 
Their full meanings are explained later on. You are also asked to carefully read the safety reg-
ulations in the applicable chapter of this handbook. 
3. TERMINOLOGY
Beware of sharp
blades: Remove plug
from mains before
maintenance or if cord
is damaged Important: Read the
instruction handbook
before using the
machine.Danger of thrown
objects. Keep other
people at a safe dis-
tance whilst working.Important: keep the
power supply cable
away from the blade.
Equipment identification
label
111312
14151618
1917
LWA
dBIPX4V~ HzkW - min-1kgS/N
6174
253
1.Acoustic power level according
to EEC directive 2000/14/CE
2.Mark of conformity according to
EEC directive 98/37
3.Year of manufacture
4.Lawnmower type
5.Serial number
6.Name and address of
Manufacturer
7.Supply voltage and frequency
11.Chassis
12.Motor
13.Blade
14.Stone-guard
15.Grass-catcher
16.Handle
17.Motor switch
18.Electric cable hook
Only for EU countries. Do not dispose of electric equipment together with household waste material! In observance
of European Directive 2002/96/EC on waste electrical and electronic equipment and its implementation in accor-
dance with national law, electric equipment that have reached the end of their life must be collected separately and
returned to an environmentally compatible recycling facility..     
						

							5EN
Guaranteed Guaranteed Vibrations in the 
ModelCutting width acoustic power acoustic pressure handle at the
level level at the ear height of the grip
CAT/E1339P37 cm 93 dB(A) 80 dB(A) 4 m/s2
5. SPECIFICATIONS
4. DESCRIPTION OF THE SYMBOLS SHOWN ON THE CONTROLS(where present)
1.Off
2.On
12