Casio QV R51 User Manual

61
BASIC IMAGE RECORDING
Flash Precautions
Take care that your fingers do
not block the flash when you
hold the camera. Covering the
flash with your finger can
greatly reduce its
effectiveness.
• You may not be able to achieve the desired results using
a flash if the subject is too close or too far away.
• The flash takes anywhere from a few seconds to as long
as 10 seconds to attain full charge after being fired. The
actual time required depends on the battery level,
temperature, and other conditions.
•...

62
BASIC IMAGE RECORDING
Using the Self-timer
The self-timer lets you select either a 2-second or 10-
second delay of the shutter release after you press the
shutter release button. A Triple Self-timer feature lets you
perform three consecutive self-timer operations to record
three images.
1.In the REC mode, press [MENU].
2.Use [
] and [] to select the “REC” tab.
3.Use [] and [] to select “Self-timer”, and
then press [].
4.Use [] and [] to select the self-timer time
you want to use, and then press...

63
BASIC IMAGE RECORDING
5.Record the image.
• When you press the
shutter release button,
the self-timer lamp
flashes and the shutter
releases after the self-
timer reaches the end
of its countdown.
• You can interrupt an
ongoing self-timer
countdown by pressing
the shutter release
button while the self-
timer lamp is flashing.
 NOTES 
• The “2 sec” self-timer setting is best when shooting
with a slow shutter speed, because it helps to avoid
blurring of images due to hand movement.
• In the case of the...

64
BASIC IMAGE RECORDING
 NOTES 
• If you plan to make large prints of your images or
otherwise use them in applications where high-
resolution is your top priority, select the “2560 x
1920” (QV-R51) or “2304 x 1712” (QV-R41) image
size.
• If you plan to send images as e-mail attachments or
otherwise use them in applications where data
economy is your top priority, select the “640 x 480”
image size.
• Selecting the “2560 x 1712 (3:2)” (QV-R51) or “2240
x 1488 (3:2)” (QV-R41) image size records images...

65
BASIC IMAGE RECORDING
 NOTE 
• Use the “Fine” setting when image quality is your top
priority and file size is secondary. Conversely, use
the “Economy” setting when file size is your top
priority and image quality is secondary.
 IMPORTANT! 
• Actual file size depends on the type of image you
record. This means that the remaining image
capacity noted on the monitor screen may not be
exactly accurate (pages 28, 180).
Downloaded From camera-usermanual.com Casio Manuals 

66
OTHER RECORDING FUNCTIONSOTHER RECORDING FUNCTIONS
This section describes other powerful features and
functions that are available for recording.
Selecting the Focus Mode
You can select one of four different focus modes: Auto
Focus, Macro, Infinity, and Manual.
1.In the REC mode, press []
(
 ).
•Each press of [] ( )
cycles thorough the focus
mode settings shown below
on the monitor screen.
[] ( )
Focus mode indicator
To set up the camera to do this:
Focus automatically (Auto Focus)
Perform close-up...

67
OTHER RECORDING FUNCTIONS
When you see this:
Green focus frame
Green operation lamp
Red focus frame
Flashing green operation lamp
It means this:
The image is focused.
The image is not in
focus.
3.Press the shutter release button the rest of
the way to record the image.

Specifying the Auto Focus Area
You can use the following procedure to change the Auto
Focus area used in the Auto Focus Mode and the Macro
Mode. Note that the configuration of the focus frame
changes in accordance with the Auto Focus...

68
OTHER RECORDING FUNCTIONS
Using the Macro Mode
The Macro mode lets you focus automatically on close up
subjects. The automatic focus operation starts when you
press the shutter release button down half way. The
following is the focus range in the Macro mode.
Range: Approximately 10cm to 70cm (3.9˝ to 27.6˝)
1.Keep pressing [] ( ) until the focus mode
indicator shows “
”.
2.Record the image.
•The focus and image recording operations are
identical to those in the Auto Focus mode.
•You can tell whether...

69
OTHER RECORDING FUNCTIONS
1.Keep pressing [] (
) until the focus
mode indicator shows
“MF”.
•At this point, a
boundary also appears
on the display,
indicating the part of the
image that will be used
for manual focus.
Using Manual Focus
With the Manual Focus mode, you can adjust the focus of
an image manually. The following shows focus ranges in
the Macro mode for two optical zoom factors.
Optical Zoom Factor
1X
3X
Approximate Focus Range
10cm (3.9˝) to infinity (∞)
60cm (23.6˝) to infinity (∞)...

70
OTHER RECORDING FUNCTIONS
Using Focus Lock
Focus lock is a technique you can use to focus on a subject
that is not located within the focus frame when you record
an image. You can use focus lock in the Auto Focus mode
and the Macro mode (
).
1.Using the monitor
screen, compose the
image so the main
subject is within the
focus frame, and then
press the shutter
release button half
way.
•You can tell whether the image is focused by
observing the focus frame and the green operation
lamp. The indications...