Casio Qt2100 User Manual
Have a look at the manual Casio Qt2100 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 338 Casio manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
QT-2100 Versatile Intelligent Terminal ——————————————————————— Installation & Down Recovery Manual Version 1.0 February 2002 c C 7 4 1 0 8 5 2 009 6 3 • QT-2100
Contents I-2 This manual is intended for use as a reference to the QT-2100 system. It provides details to install systems and down recovery. This manual does not describe actual programming, which is covered in the QT-2100 programming manual. This manual consists of the following chapters: 1. System installation This chapter show the procedure of installing QT-2100 systems. 2. System down and recovery This chapter explains actions to take and recovery methods when the system goes down. Note: Casio reserves the right to change equipment and specifications without obligation and notification. The terms used in this manual may be different from those used in other manuals of Casio’s products. Printing history Manual version Software version Version 1.0: February, 2002 First Edition: February, 2002 Version 1.0 Revised points
I-5QT-2100 Installation & Down Recovery Manual 1. System installation ........................................................................................ I-6 1-1. How to load IPL (Initial Program Loading) .................................................................. I-6 1-1-1. From PC to QT-2100 terminal via RS-232C ..................................................... I-6 1-1-2. From one QT-2100 to QT-2100 terminals via inline ......................................... I-7 1-1-3. From CF card to QT-2100 terminal .................................................................. I-7 1-2. How to install QT-2100 system ................................................................................... I-8 1-2-1. QT-2100 stand alone system (with printer) ...................................................... I-8 1-2-2. QT-2100 master/satellite system (with local printer) ........................................ I-8 1-2-3. QT-2100 master/satellite system (with remote printer) ..................................... I-9 1-2-4. Printer DIP switch configuration ..................................................................... I-10 2. System down and recovery ........................................................................ I-11 2-1. Measures to prevent trouble ..................................................................................... I-12 2-2. Master terminal failure .............................................................................................. I-13 2-2-1. Check tracking master terminal failure ........................................................... I-13 2-2-1-1. Detection of check tracking master terminal failure ........................................ I-13 2-2-1-2. Master failure during check tracking operation ............................................... I-14 2-2-2. Remote printer failure ..................................................................................... I-15 2-2-2-1. Detection of remote printer failure .................................................................. I-15 2-2-2-2. Master printer failure during printing on remote printer .................................. I-15 2-3. Recovery processing ................................................................................................ I-16 2-3-1. Master/backup master down detection ........................................................... I-16 2-3-2. When both master and backup master go down ............................................ I-16 2-4. Master failure during X/Z collection/consolidation or terminal data transfer ............. I-16 2-5. Satellite terminal down .............................................................................................. I-16
I-6 System Installation 1. System installation In this chapter shows how to install QT-2100 systems and peripherals. 1-1. How to load IPL (Initial Program Loading) Normally, IPL is not necessary since QT-2100 has efficient program options to meet your circumstances. In some cases, you need to change the application program to meet your requirements, the IPL is necessary to download the application program to QT-2100. To load IPL, there are three methods: 1) From PC to QT-2100 terminal via RS-232C 2) From one QT-2100 terminal (master) to QT-2100 terminals (satellite) via inline 3) From CF card to QT-2100 terminal 1-1-1. From PC to QT-2100 terminal via RS-232C 1. Set up the system (refer to the left figure). 2. Initialize the target QT-2100 to receive the IPL data (refer to the Machine initialization section of the Manager operation chapter of QT-2100 Reference manual page 95). 3. Run the loading program of PC. 4. After IPL completion, continue to the initialize operation. QT2100 PC IPL source IPL target COM 1 COM port IPL Data
I-7QT-2100 Installation & Down Recovery Manual 1-1-2. From one QT-2100 to QT-2100 terminals via inline 1. Set up the system (refer to the left figure). 2. Initialize the target QT-2100 to receive the IPL data (refer to the Machine initialization section of the Manager operation chapter of QT-2100 Reference manual page 95.) 3. Execute IPL data sending operation (refer to the Auto-program operation section of the Manager operation chapter of QT- 2100 Reference manual page 125.) 4. After IPL completion, continue to the initialize operation. IPL source IPL Data In-line QT2100 QT2100 IPL targetIn-line (CASIO original cable or CAT5 cable) QT2100QT2100QT2100 1-1-3. From CF card to QT-2100 terminal 1. Insert the CF card to the CF card slot of the target terminal. 2. Initialize the target QT-2100 to receive the IPL data (refer to the Machine initialization section of the Manager operation chapter of QT-2100 Reference manual page 95.) 3. Execute IPL data receiving operation (refer to the Machine initialization section of the Manager operation chapter of QT- 2100 Reference manual page 125.) 4. After IPL completion, continue to the initialize operation. QT2100 CF card
I-8 System Installation 1-2. How to install QT-2100 system 1-2-1. QT-2100 stand alone system (with printer) 1. Set up the system (refer to the left figure). 2. Initialize the QT-2100 (refer to the Initialization chapter of QT-2100 Programming manual page 8.) Note 1: If the QT-2100 cannot recognize the printer(s) correctly, check the dip switches on the printer or printer cable and try initialization operation again. Casio printer cable (PRT- CB-8A/-8B) is required for proper recognition of the local printer. Note 2: If the Slip printer is connected to COM 4, 5, or 6 port, automatic printer detection during initialization is not made. In this case, program the I/O parameter file manu- ally and flag clear the machine. 3. Complete the initialize operation. 1-2-2. QT-2100 master/satellite system (with local printer) 1. Set up the system (refer to the figure below). 2. Initialize the master QT-2100 (refer to the Initialization chap- ter of QT-2100 Programming manual page 8.) Note 1: 1. Do not turn on other QT-2100. 2. If the QT-2100 cannot recognize the local printer(s) cor- rectly, check the dip switches on the printer or printer cable and try initialization operation again. Casio printer cable (PRT-CB-8A/-8B) is required for proper recognition of the local printer. Note 2: If the Slip printer is connected to COM 4, 5, or 6 port, automatic printer detection during initialization is not made. In this case, program the I/O parameter file manu- ally and flag clear the machine. QT2100 R/J Slip In-line (CASIO original cable/CAT5 TUP cable) QT2100QT2100QT2100 R/JR/JR/JR/JR/JR/J PRN (1)... PRN (3) PRN (1)...PRN (3) PRN (1)...PRN (3) PRN (1) QT2100 R/J Slip R/J PRN (1)...PRN (3)
I-9QT-2100 Installation & Down Recovery Manual 3. Initialize QT-2100 terminals one by one. Note: When you want to copy master program to satellites, complete the master program, and then initialize the satel- lite and receive the master program during initialization procedure of satellites. 1-2-3. QT-2100 master/satellite system (with remote printer) 1. Set up the system (refer to the figure below). 2. Initialize the master QT-2100 (refer to the Initialization chap- ter of QT-2100 Programming manual page 8.) Note 1: 1. Do not turn on other QT-2100. 2. If the QT-2100 cannot recognize the local printer(s) cor- rectly, check the dip switches on the printer or printer cable and try initialization operation again. Casio printer cable (PRT-CB-8A/-8B) is required for proper recognition of the local printer. Note 2: If the Slip printer is connected to COM 4, 5, or 6 port, automatic printer detection during initialization is not made. In this case, program the I/O parameter file manu- ally and flag clear the machine. 3. Initialize QT-2100 terminals one by one. Note: When you want to copy master program to satellites, complete the master program first, and then initialize the satellites and receive the master program at the end of initialization procedure of satellites. 4. Declare remote printer by programming the printer connection table to all terminals in the system (refer to the Programming printer connection section in the Program 3 chapter of the Programming manual page 70.) QT2000 R/J SlipSlipSlip In-line QT2000QT2000QT2000 RP RP RP R/J PRN (1)...PRN (3)PRN (1)...PRN (3)
I-10 System Installation SW No. Function Data reception error Receive buffer capacity Handshaking Data word length Parity check Parity selection Transmision speed ON OFF Ignored Prints ? 45 bytes 4k bytes XON/XOFF DTR/DSR 7 bits 8 bits Ye s N o Even Odd See transmission speed setting Density setting Light DarkSW No. 3 ON OFF ON OFF4 ON OFF OFF ON UP-350 Bottom view DSW1DSW2 1 2 3 4 5 6 7 8 1 SW No. Function Busy condition Reserved Print density Reserved Reserved I/F 6 pin reset signal I/F 25 pin reset signal ON OFF Buffer fullBuffer full or Offline Fixed See density setting Fixed Fixed Enabled Disabled Enabled Disabled1 2 3 4 5 6 7 8 2 Transmission speed setting bps 2400 4800 9600 19200SW No. 7 ON OFF ON OFF8 ON ON OFF OFF SW No. Function Data word length Parity check Parity type Data tranfer rate Connection of customer display Data reception error Hand shake ON OFF 7 bit 8 bit Ye s N o Even Odd See data transfer rate setting ConnectedNot connected Ignored Print ? XON/XOFF DTR/DSR SA-3015 Bottom view DSW1 DSW2 1 2 3 4 5 6 7 8 1 SW No. Function Automatic CR Reception buffer size Font selection Carriage speed Busy condition Internal use I/F 6 pin reset signal I/F 25 pin reset signal ON OFF Always Yes Always No 32 bytes 2048 bytes 9 x 9 7 x 9 Low High Buffer fullBuffer full or Offline Fixed Enabled Disabled Enabled Disabled1 2 3 4 5 6 7 8 2 Data tranfer rate setting bps 1200 2400 4800 9600SW No. 4 ON OFF ON OFF5 ON ON OFF OFF 1-2-4. Printer DIP switch configuration UP-350 SA-3015 SW No. Function Data reception error Receive buffer capacity Handshaking Data word length Parity check Parity selection Baud rate Busy condition ON OFF Ignored Prints ? 40 bytes 1k byte XON/XOFF DTR/DSR 7 bits 8 bits Ye s N o Even Odd 4800 bps 9600 bps Buffer fullBuffer full or Offline1 2 3 4 5 6 7 8 1 SW No. Function No. of digits (7x9 font / 9x9 font) Internal use #6 pin reset signal #25 pin reset signal ON OFF 42 / 35 40 / 33 digits digits Enabled Disabled Enabled Disabled1 2 3 4 2 UP-250 Dip switch is located at the bottom of the printer.