Casio Projector XJ-V10X User Manual

							71
No sound output from the 
AUDIO OUT terminalThe projector’s volume level setting may be too low or muted. Use the remote 
controller [VOLUME +] and [VOLUME –] keys to adjust the volume level. See page 
20.
The volume level setting of the device connected to the projector is too low or the 
other device is not outputting audio. Adjust the volume level of the connected 
device.
The audio output of the connected device may not be connected correctly to the 
projector’s AUDIO IN terminal. Check the connection.
No sound output from the 
speaker (XJ-F Series)The projector’s volume level setting may be too low or muted. Use the remote 
controller [VOLUME +] and [VOLUME –] keys to adjust the volume level. See page 
20.
The volume level setting of the device connected to the projector is too low or the 
other device is not outputting audio. Adjust the volume level of the connected 
device.
The audio output of the connected device may not be connected correctly to the 
projector’s AUDIO IN terminal. Check the connection.
When the input source is “HDMI”, “File Viewer”, “Network” or “USB Display”, 
“Line” may be selected for the “Option Settings 2  Audio Out” setting on the 
setup menu. Change the “Audio Out” setting to “Speaker”. See page 30.
Strange color The input signal may not match projector settings. Try doing the following.
– Press the [FUNC] key and then select “Brightness” to adjust image brightness.
– Press the [FUNC] key and then select “Color Mode” to change the color mode.
– On the setup menu, use “Image Adjustment 1  Color Balance” to adjust the 
projection image color balance.
Text is blurry.The image may be out of focus. Adjust image focus.
The current frequency and/or phase setting do not match the input signal. (Applies 
only when the input source is an RGB signal.) Press the [AUTO] key to execute an 
automatic adjustment operation.
On the setup menu, perform the “Image Adjustment 2  Frequency” and “Image 
Adjustment 2  Phase” adjustments. (Applies only when the input source is an 
RGB signal.) See page 27.
The message “Please input 
the password.” appears 
and further operation is not 
possible.The “Option Settings 1  Power On Password” setting on the setup menu is turned 
on, so the projector is password protected. Input the correct password, and then 
press the [ENTER] key. See page 32.
The remote controller does 
not work.The remote controller batteries may be dead. Replace the batteries.
The remote controller may be too far from the projector. Make sure the remote 
controller is within about five meters from the projector when performing 
operations.
The POWER/STANDBY 
indicator is lit red and the 
STATUS indicator is lit (or 
flashing) red or amber.An error occurred. See “Error Indicators and Warning Messages” (page 69).
The light source unit does 
not light.The light source has been temporarily shut off by pressing the [BLANK] key. Press 
the [BLANK] key or [ESC] key to turn it back on. For more information, see “To 
momentarily blank the image and mute the audio (BLANK)” (page 17).
The light source unit has reached the end of its service life or it is malfunctioning. 
Contact your original dealer or authorized CASIO service center for replacement.
ProblemCause and Recommended Action 
						

							72
Important!Try performing the following steps, which may or may not return the projector to normal 
operation.
If normal operation does not resume after you perform the above steps, take the projector to 
your retailer or authorized CASIO service center.
Power suddenly turns off 
and the projector restarts.The projector periodically performs a self-check operation. In rare cases, the result of 
a self-check may cause the projector to restart automatically. This normally does not 
indicate malfunction, so you can continue using the projector.
However, malfunction may be indicated if successive restarts keep occurring. If this 
happens contact your original dealer or authorized CASIO service center.
1. Unplug the AC power cord and wait for at least 10 minutes.
2. Plug the power cord back in and turn the projector back on again.
ProblemCause and Recommended Action 
						

							73
Appendix
This section explains how to establish a component video connection between the projector and a 
video device.
Component video output terminals come in 3-terminal sets: Y·Cb·Cr or Y·Pb·Pr. Be sure to match 
the colors of the plugs on a component video cable with the colors of the terminals (Green: Y; 
Blue: Cb/Pb; Red: Cr/Pr).
Note that connection only to an analog component video output terminal is supported.
Connection to a digital output terminal is not supported.
XJ-V Series
Connecting to a Component Video Output
Projector
Stereo mini plug  Pin plug type audio cable 
(commercially available)To component video 
output terminals
Component video cable (commercially available)To audio output terminals
White
Red COMPUTER terminal
AUDIO IN terminal
Video device 
						

							74
XJ-F Series
NoteNote that regardless of whether the image being projected is being input via the projector’s 
S-VIDEO terminal or VIDEO terminal, the projector outputs audio that is input via the 
projector’s AUDIO IN L/R terminals.
Connecting to a Composite Video Output or S-Video 
Output (XJ-F Series Only)
Projector
Video device
Stereo mini plug  Pin plug type audio cable 
(commercially available)To component video 
output terminals
Component video cable (commercially available)To audio output terminals
White
Red COMPUTER terminal
AUDIO IN terminal
To S-video output terminal
To video/audio output terminal
Yellow: To VIDEO terminal To S-VIDEO terminal
Red: To AUDIO IN R terminal
White: To AUDIO IN L terminal
Projector
Video deviceS-video cable (commercially available)
Pin plug type video/audio cable 
(commercially available) 
						

							75
Power can be supplied to external equipment via the USB-A/DC 5V port of an XJ-F20XN, XJ-F200WN, 
or XJ-F210WN model projector, or via the DC 5V port of an XJ-F10X or XJ-F100W model projector.
Important!Turning off projector power also cuts power being supplied to external equipment. Note that 
power being supplied is also cut when the projector is turned off due to restarting by its 
self-check function or Auto Power Off, due to some error, or for any other reason. Depending 
on the external equipment being used, cut off of the power supply may cause data that is 
being edited to be lost or corrupted. Make it a habit to frequently save data on external 
equipment being powered by the projector.
Projector power being turned off by Auto Power Off (page 29) also causes power to external 
equipment to be cut off. Before starting power supply to external equipment, be sure to select 
“Off” for the setting “Option Settings 1 3 Auto Power Off” to disable Auto Power Off.
For a list of external equipment whose operation has been confirmed while being powered by 
the projector, visit the CASIO projector website (http://www.casio-intl.com/support/). Proper 
operation is not guaranteed for any external device that is not included in the list at the CASIO 
projector website.
Though power up to 5V DC 2A can be supplied to other devices not included on the CASIO 
website, note that doing so may make some functions unavailable on some devices. Before 
using output from this port to power another device, be sure to check the user documentation 
of the device and make sure you connect it correctly. Particular care is required when 
connecting a chargeable battery to this projector’s USB port power supply. Incorrect 
connection creates the risk of explosion, fire, and smoke.
Note that CASIO COMPUTER CO., LTD. shall be held in no way liable for any loss or 
corruption of data stored on an external device connected to this projector’s USB port power 
supply, or for any damage, smoke generation, or fire occurring on the connected device.
NoteTo temporarily blank projection while maintaining power supply from the projector to external 
equipment, press the [BLANK] key. For more information, see “To momentarily blank the 
image and mute the audio (BLANK)” (page 17).
Supplying Power to External Equipment 
(XJ-F Series Only) 
						

							76
With an XJ-V Series projector, you can update firmware (software in the projector flash ROM) using a 
computer. With an XJ-F Series projector, you can update firmware and also transfer images to the 
projector to be used as a user logo.
For details about these operations, refer to the “Projector Firmware Update Guide” and “User Logo 
Transfer Guide”, which are available for download from the CASIO projector website.
To update firmware and transfer a user logo
Use a commercially available USB cable to connect the projector’s SERVICE port (XJ-V Series 
models) or LOGO port (XJ-F Series models) to your computer’s USB port.
The projector can be hung from a ceiling. When hanging a projector from the ceiling, you can orient it 
upside down or with the projection lens facing straight downwards.
For full details, contact the retailer where you purchased the projector.
Important!When hanging the projector from a ceiling, make sure that it is at least one meter away from 
fire detectors, fire alarms, and other fire protection devices. Locating the projector too close to 
a fire protection device creates the risk of mis-operation of the device due to warm air 
exhausted from the projector. Also, avoid locating the projector close to fluorescent lights or 
other strong light sources. Bright light can shorten the operating range of the remote controller 
or even make remote control impossible. When selecting a location for the projector, be sure 
to test for proper operation of the remote controller.
The vertical and horizontal orientation of the projected image is reversed from normal when 
the projector is positioned upside down for hanging from a ceiling. You need to change the 
setup of the projector in order to correct for this. For details, see “Screen Settings 3 Ceiling 
Mount” (page 28) under “Setup Menu Settings”.
Updating Firmware and Transferring a User Logo
Hanging the Projector from a Ceiling
SERVICE port
(Micro-USB Type B)LOGO port
(Micro-USB Type B)
XJ-V Series XJ-F Series 
						

							77
The projection distance values below are for reference when setting up the projector.
“h” in the illustration and table indicates the distance between the center of the projector lens and 
the bottom edge of the projection screen.
Projection Distance and Screen Size
Projection Size
Approximate Projection Distance
XJ-V10X/XJ-F10X/XJ-F20XNXJ-V100W/XJ-V110W/XJ-F100W/
XJ-F200WN/XJ-F210WN
Screen 
SizeDiagonal
(cm)Minimum 
Distance
(m / feet)Maximum 
Distance
(m / feet)hMinimum 
Distance
(m / feet)Maximum 
Distance
(m / feet)h
(cm / inch)
30 76 0.93 / 3.05 1.38 / 4.53 0 – – –
35 89 – – – 0.92 / 3.02 1.37 / 4.49 8 / 3.15
40 102 1.27 / 4.17 1.88 / 6.17 0 1.06 / 3.48 1.58 / 5.18 9 / 3.54
60 152 1.95 / 6.4 2.87 / 9.42 0 1.64 / 5.38 2.42 / 7.94 13 / 5.12
77 196 2.54 / 8.33 3.72 / 12.2 0 2.14 / 7.02 3.14 / 10.3 17 / 6.69
80 203 2.64 / 8.66 3.86 / 12.66 0 2.22 / 7.28 3.26 / 10.7 18 / 7.09
100 254 3.33 / 10.93 4.85 / 15.91 0 2.81 / 9.22 4.11 / 13.48 22 / 8.66
150 381 5.04 / 16.54 7.33 / 24.05 0 4.26 / 13.98 6.22 / 20.41 34 / 13.39
200 508 6.76 / 22.18 9.82 / 32.22 0 5.72 / 18.77 8.32 / 27.3 45 / 17.72
300 762 10.18 / 33.4 14.78 / 48.49 0 8.63 / 28.31 12.54 / 41.14 67 / 26.38
h   
						

							78
The following shows how images are projected in accordance with the type of the input signal and the 
aspect ratio setting of the projector.
XJ-V100W/XJ-V110W/XJ-F100W/XJ-F200WN/XJ-F210WN
Input source: RGB or HDMI(PC)
Input source: Video*, S-Video*, Component or HDMI(DTV)
*XJ-F100W/XJ-F200WN/XJ-F210WN only
Aspect Ratio Setting and Projection Image
Input SignalNormalFull16:94:3True
SVGA (800 × 600)
XGA (1024 × 768)
WXGA (1280 × 800)
SXGA (1280 × 1024)
Input SignalNormal16:916:104:3Letter Box
4:3 Aspect Image
Squeezed Image
Letter Box Image
16:9 Aspect Image 
						

							79
XJ-V10X/XJ-F10X/XJ-F20XN
Input source: RGB or HDMI(PC)
Input source: Video*, S-Video*, Component or HDMI(DTV)
*XJ-F10X/XJ-F20XN only
Input SignalNormalFull16:916:10
SVGA (800 × 600)
XGA (1024 × 768)
WXGA (1280 × 800)
SXGA (1280 × 1024)
Input SignalNormal16:916:104:3
4:3 Aspect Image
Squeezed Image
Letter Box Image
16:9 Aspect Image 
						

							80
Important!Even if a signal is listed in the table below, it does not guarantee that you will be able to 
display its images correctly.
RGB Signal
Supported Signals
Signal NameResolutionHorizontal Frequency 
(kHz)Vertical Frequency 
(Hz)
VESA640 × 480/60 640 × 480 31.5 60
640 × 480/72 640 × 480 37.9 73
640 × 480/75 640 × 480 37.5 75
640 × 480/85 640 × 480 43.3 85
800 × 600/56 800 × 600 35.2 56
800 × 600/60 800 × 600 37.9 60
800 × 600/72 800 × 600 48.1 72
800 × 600/75 800 × 600 46.9 75
800 × 600/85 800 × 600 53.7 85
1024 × 768/60 1024 × 768 48.4 60
1024 × 768/70 1024 × 768 56.5 70
1024 × 768/75 1024 × 768 60.0 75
1024 × 768/85 1024 × 768 68.7 85
1152 × 864/75 1152 × 864 67.5 75
1280 × 720/60 1280 × 720 45.0 60
1280 × 768/60 1280 × 768 47.8 60
1280 × 800/60 1280 × 800 49.7 60
1280 × 960/60 1280 × 960 60.0 60
1280 × 1024/60 1280 × 1024 64.0 60
1280 × 1024/75 1280 × 1024 80.0 75
1280 × 1024/85 1280 × 1024 91.1 85
1366 × 768/60 1366 × 768 47.7 60
1400 × 1050/60 1400 × 1050 65.3 60
1440 × 900/60 1440 × 900 55.9 60
1600 × 1200/60 1600 × 1200 75.0 60
1680 × 1050/60 1680 × 1050 65.3 60
1920 × 1080/60 1920 × 1080 67.5 60
1920 × 1200RB/60 1920 × 1200 74.0 60