Casio Projector XJ-S31 XJ-S36 XJ-S41 XJ-S46 User Manual

							
11
Configuring Advanced Projector Settings
Your projector has a setup menu that you can use to configure advanced settings.
Displaying the Setup Menu
Pressing the [MENU] key displays the menu  shown below in the center of the projection 
screen.
Note
You can position the setup menu in the c enter or on the left edge of the projection 
screen. For details, see “Menu Position” under  “Option Settings 1 Main Menu” on page 
24.
To exit the setup menu
Press the [MENU] key.
Configuring Set up Menu Settings
1Press the [MENU] key to display the setup menu.
2Use the [T] and [ S] keys to select the main menu item you want by 
highlighting it.
3Press the [ENTER] key.
4Use the [ T] and [ S] keys to select the sub-menu item you want by highlighting 
it.
5Perform the required operation on the selected sub-menu item screen.
z The guidance text explains the operations you need to perform to configure each setting.
6To return to the main menu from the sub-menu, press the [ESC] key.
7To exit the setup menu, press the [MENU] key.
Basic Setup Menu Operations
Main menu
The main menu includes eight (nine on the 
XJ-S36/XJ-S46) main menu items. The 
currently selected main menu item is the one 
that is highlighted.
Sub-menu
The sub-menu shows each individual setting 
under each main menu item, and its current 
setting.
Guidance text
Guidance text provides a brief description of the 
main key operations available for the operation 
you are currently performing. 
						

							
12
Basic Setup Menu Example
The procedure below shows how to configure the following three settings:
 Image Adjustment  J Contrast
 Image Adjustment  J Color Mode
 Option Settings 1  J Eco Mode
Note
z Certain settings on the setup menu cannot  be changed while there is no input signal 
to the projector. Because of this, you  should configure setup menu settings after 
selecting an input source  and starting projection.
z This example covers basic steps only. For  more detailed information, see “Setup Menu 
Contents” on page 17.
To configure the “Image Adjustment  J Contrast” setting
1Press the [MENU] key to display the setup menu.
2“Image Adjustment” is initially selected on the main menu, so simply press the 
[ENTER] key.
3Press the [ T] key once to select “Contrast”.
4Use the [ W] (lighter) and [ X] (darker) keys to adjust contrast.
To configure the “Image Adjustment J Color Mode” setting
5Press the [ T] key once to select “Color Mode”.
6Press the [ENTER] key.
z This displays the color mode menu.
7Use the [ T] and [ S] keys to select the color mode you want.
8After selecting the color mode you want, press the [ESC] key. 
						

							
13
To configure the “Option Settings 1 J Eco Mode” setting
9Press the [ESC] key.
10Press the [ T] key four times to select “Option Settings 1”.
11Press the [ENTER] key.
12Press the [ T] key three times to select “Eco Mode”.
13Use the [ W] and [ X] keys to select “On” or “Off”.
14After you are finished, press the [MENU] key to exit the setup menu.
The password feature lets you keep unauthorized individuals from using the projector. You 
can specify whether password input  is required whenever you turn on the projector, and you 
can specify and change the passwor d as required. Use the setup menu “Option Settings 1 
J  Power On Password” setting to configure power on password settings.
Inputting a Password
The password of your projector is not really  a “word” made up of letters, but rather a 
sequence of remote controller key inputs. The following is the 8-key sequence that 
represents the initial factory default password.
Using the Password Feature
Note the following precautions whenever you use the password feature.
 The password feature protects against unauthorized  use of the projector. Note that it is 
not an anti-theft measure.
 You will need to enter the initial factory default password the first time you use the  projector after turning on the password feature. Change the initial factory default 
password to a different one of your choice as soon as possible after turning on the 
password feature.
 Remember that password operations are alwa ys performed using the remote controller, 
so you should take care not to lose or misplace the remote controller.
 Also note that you will not be able to input  the password if the remote controller battery 
is dead. Replace the remote control battery as soon as possible after it starts to go 
low.
Password Protecting the Projector
[INPUT][AUTO][BLANK][FREEZE][ S][T ][W ][X ] 
						

							
14
If you forget your password...
You will not be able to use the projector if you forget the password for some reason. If 
you forget the password, you will need to bring the following two items to your CASIO 
distributor to have the password cleared. Note that you will be charged to have the 
password cleared.
1. Personal identification (original or copy of you driver’s license, employee I.D., etc.)
2. Projector unit
Note that your CASIO distributor will not be  able to clear the password of your projector 
unless you bring both of the items listed above.
Also, keep the projector’s warranty in a safe place.
Important!
Having your password cleared us ing the procedure described above will return all of the 
settings of your projector, except for the  lamp time, to their initial factory defaults.
Keep a written record of your password!
You will not be able to use the projector if you forget its password. We strongly suggest 
that you keep a written or other type of record of the password so you can look it up 
when necessary.
To change the password
1Press the [MENU] key to display the setup menu.
2Use the [T] key to select “Option Settings 1”, and then press the [ENTER] key.
3Use the [ T] key to select “Power On Password”, and then press the [ENTER] 
key.
z This will display a dialog box prompting you to enter the current password.
4Enter the current password.
zIf the projector is still protected by the factory default password, perform the key 
operation shown below to enter it.
5After entering the current password, press the [ENTER] key.
zThis displays the Power On Password setting screen.
6Use the [ T] key to select “Change Password”, and then press the [ENTER] key.
z This will display a dialog box prompting you to enter the new password.
[INPUT][AUTO][BLANK][FREEZE][ S][T ][W ][X ] 
						

							
15
7Enter a key sequence up to eight key operations long.
zYou can use any of the following keys as part of your password key sequence. 
[INPUT], [AUTO], [BLANK], [FREEZE], [COLOR MODE], [D-ZOOM +], 
[D-ZOOM –], [KEYSTONE +], [KEY STONE –], [MENU], [POINTER], 
[ ], [U], […], [S ], 
[ T ], [ W], [ X], [FUNC]
8After entering the new password, press the [ENTER] key.
z This will display a dialog box prompting you to enter the same password again.
9Re-enter the same password key sequence you entered in step 7 and then press 
[ENTER].
zThe message “Your new password has been registered.” indicates that the password has 
been changed. Press the [ESC] key.
z If the password you entered in this step is different from the one you entered in step 7, 
the message “The password you input is wrong.” appears. Press the [ESC] key to return 
to step 7.
10After you are finished, press the [MENU] key to exit the setup menu.
To turn password protection on and off
1Display the Power On Password setting screen by performing steps 1 through 5 
of the procedure under “To change the password” on page 14.
zAt this time, make sure that “Power On Password” is selected on the Power On 
Password setting screen.
2Use the [ W] and [ X] keys to select “On” or “Off”.
z Changing the power on password setting from “On” to “Off ” causes the confirmation 
dialog box shown below to appear.
Press the [ENTER] key to confirm that you want to turn on power on password 
protection, or [ESC] to exit the dialog box without doing anything.
3After you are finished, press the [MENU] key to exit the setup menu.
Entering the Password when  Turning On the Projector
When you turn on the projector while passw ord protection is turned on will cause a 
password input dialog box to appear on the proj ection screen. All projector operations will 
be accessible to you after you input the correct password and press the [ENTER] key.
Note
You can perform the projection  size adjustment operation ([ZOOM +] / [ZOOM –] keys), 
focus operation ([FOCUS  S] / [FOCUS  T] keys), and power off operation ([ ] key) 
while the password input dialog box is on the projection screen. 
						

							
16
You can use the procedures in this section to restore all of the settings on a particular main 
menu or all of the settings on the setup menu to their initial factory defaults.
To restore all settings on a particular  main menu to their initial factory 
defaults
1Press the [MENU] key to display the setup menu.
2Use the [ T] and [ S] keys to select the main menu whose settings you want to 
restore to their initial factory defaults.
z You can select Image Adjustment, Volume Adjustment, Screen Settings, Input Settings, 
Option Settings 1, or Option Settings 2.
3Press the [ENTER] key.
4Use the [ T] key to select “Restore Menu Defaults”.
5Press the [ENTER] key.
z This will display a confirmation screen like the screen shown below.
6Use the [ S] key to select “Yes”.
7To restore the settings of the main me nu to their initial defaults, press the 
[ENTER] key.
z To exit the operation without doing anything, press [ESC] instead of [ENTER].
8After you are finished, press the [MENU] key to exit the setup menu.
Note
zThe language setting and the password are not re turned to their initial factory defaults 
if you select Option Settings 1 in step 3.
z For details about how the above procedure in itializes settings, see the explanations of 
the settings under “Setup Menu Contents” on page 17.
Restoring Projector Settings  to Their Initial Factory 
Defaults 
						

							
17
To restore all settings on the setup menu to their initial factory defaults
1Press the [MENU] key to display the setup menu.
2Use the [T] key to select “Restore All Defaults”, and then press the [ENTER] 
key.
z This displays a confirmation message asking if you want to initialize all settings.
3Use the [ S] key to select “Yes”.
4To restore all settings on the setup me nu to their initial defaults, press the 
[ENTER] key.
z This will restore all of the settings to their initial factory defaults, except for the 
Language, Lamp Time, and password settings.
z To exit the operation without doing anything, press [ESC] instead of [ENTER].
5After you are finished, press the [MENU] key to exit the setup menu.
This section contains tables that provide detai led explanations of all of the items included on 
the setup menu. The following describes the type of information that appears in each of the 
columns of the tables.
Setting Name
This column shows the names of the settings as they appear on the sub-menu.
Input
This column shows the input source  for which each setting is supported.
Input source names are abbreviated as R (R GB input), C (component video input), V (video 
input), and U (USB input, XJ-S36/XJ-S46 only).  The letter N indicates that the setting can be 
configured while ther e is no input signal.
Setting Unit
The setting unit indicates how a setting is stored.
“Source Specific” in this column indicates  that separate settings can be stored for each 
individual input source. For example,  you could store an “Image Adjustment  J Brightness” 
setting of –1 for RGB input and a setting of +1 for VIDEO input.
“Single” in this column indicates that a singl e setting is stored and applied, regardless of the 
input source.
Description
This column provides details about the setting item and how to select it. The initial default 
setting is indicated by an asterisk ( *).
Setup Menu Contents 
						

							
18
Image Adjustment Main Menu
Setting NameInputSetting UnitDescription
Brightness RCVU Source  SpecificUse this sub-menu to adjust the brightness of the 
projected image. A larger value produces a brighter 
image.
Contrast RCVU Source  SpecificUse this sub-menu to adjust the contrast of the projected 
image. A larger value produces a stronger contrast.
Sharpness RCV Source 
Specific Use this sub-menu to adjust the sharpness of the outlines 
in the projected image. A larger value makes the image 
sharper, while a smaller value makes it softer.
Saturation RCV Source 
Specific Use this sub-menu to adjust the color saturation of the 
projected image. A larger value increases color saturation.
Tint RCV Source 
Specific Use this sub-menu to adjust the tint of the projected 
image. A larger value makes the overall image more 
bluish, while a smaller value makes the overall image 
more reddish. This setting is supported only when the 
signal is NTSC or NTSC4.43.
Color Mode RCVU Source  SpecificYou can select from among five different color mode 
settings to optimize the projected image in accordance 
with image contents and projection conditions.
Presentation
*:
Use this setting for standard presentations in a well-lit 
area. This is the initial default setting when the input 
source is either RGB or USB.
Standard:
Use this setting when you want to highlight the colors of 
your presentation.
Graphics:
Use this setting when you want photographs and graphics 
to appear natural.
Theater *:
Use this setting to bring out the dark portions of your 
images. This is the initial def ault setting when the input 
source is either component video or video.
Blackboard:
Use this setting for easy viewing when projecting onto a 
blackboard.
Color Balance RCVU Source  SpecificThis sub-menu lets you adjust the color balance of the 
projected image. Color balance lets you select either 
“Color Temperature” or “Color” (for individual adjustment of 
red, green and blue) as the adjustment method.
Color Temperature:
Select this option when you want to adjust the color 
temperature. Selecting “LO” gives whites a reddish cast, 
while “HI” gives them a bluish cast. Selecting “NORM
*” 
sets a medium setting between the two colors.
Color:
Select this option when you want to individually adjust the 
intensity of red, green, and blue. For all of the colors, a 
larger value makes the color stronger. 
						

							
19
About the “Signal Specific” Setting Unit
For the items that have “Signal Specific” in the “Setting Unit” column of the above table, 
the setting is saved for the specific type of signal (XGA/60Hz, SXGA/60Hz, etc.) that is 
being input when the setting is performed, and not for a specific input source.
Ve r t i c a l  
Po sitionRCV Signal 
Specific Use this sub-menu to adjust the vertical position of the 
input source image within the projection area.
Horizontal 
Po sition RCV Signal 
Specific Use this sub-menu to adjust the horizontal position of the 
input source image within the projection area.
Frequency R Signal  SpecificWhen vertical bands appear in the projected image while 
RGB is selected as the input source, it means that the 
frequency setting is not correct. When this happens, use 
this setting to adjust the frequency manually.
Important!If, for some reason, your manual frequency settings 
cause the image input from the computer to 
disappear from the projection, you can press the 
[AUTO] key to perform an auto adjust operation, 
which should cause the image to appear.
Phase R Signal  SpecificWhen there is flickering in the projected image while RGB 
is selected as the input source, it means that the phase 
setting is not correct. When this happens, use this setting 
to adjust the phase manually.
Video Mode RCV Source 
Specific This setting is valid when VIDEO is selected as the input 
source. Use it to select a mode that is optimized for 
movies or still images.
Normal
*:
Optimized for movies.
Still Image :
Optimized for still images. In particular, this setting should 
be used when projecting still images from a digital 
camera connected to the projector’s VIDEO terminal.
Restore Menu 
Defaults RCVU Source 
Specific Use this sub-menu to return all of the sub-menu items on 
the Image Adjustment main menu to their initial default 
settings.
z
Restoring menu defaults when there is no input signal 
will restore defaults for the currently selected input 
source.
z “Image Adjustment” main menu “Vertical Position”, 
“Horizontal Position”, “Frequency”, and “Phase” defaults 
can be restored for the current signal type (XGA/60Hz, 
SXGA/60Hz,etc.) only.
Setting NameInputSetting 
UnitDescription 
						

							
20
Volume Adjustment Main Menu
Setting NameInputSetting UnitDescription
Volume RCV UN Source 
Specific Use this sub-menu to adjust the volume level of the 
projector’s speaker.
z
Changing this setting when there is no input signal 
changes the volume setting of the currently selected 
signal source.
Restore Menu 
Defaults RCV
UN Source 
Specific Use this sub-menu to return Volume to its initial default 
setting.
z
Restoring menu defaults when there is no input signal 
will restore defaults for the currently selected input 
source.