Casio Projector XJ-M250 XJ-M255 User Manual

							41
POWER : Green steady A system problem has occurred, which may cause problems with some 
functions. Turn off the projector, disconnect the power cord from the 
projector and wait for all of the projector’s indicators to go out. Next, 
reconnect the power cord and turn the projector back on.
If the error occurs again when you turn power back on, contact your 
retailer or nearest authorized CASIO Service Center.
Press the [ESC] key to clear the warning message. LIGHT : –
TEMP : –
Message : A system problem has 
occurred. Normal 
projection is not possible.
POWER : Green steady
LIGHT : –
TEMP : –
Message : There is some problem 
with the system.
The audio function may 
not operate correctly.
POWER : Green steady The USB or LAN connection was terminated because of a problem with 
the USB port or LAN port. To use the USB or LAN function, turn off the 
projector and then turn it back on again.
If the error occurs again when you turn power back on, contact your 
retailer or nearest authorized CASIO Service Center.
Press the [ESC] key to clear the warning message. LIGHT : –
TEMP : –
Message : Some problem occurred 
with the USB port or LAN 
terminal.
POWER : Amber flashingJ 
Red steadyThe projector was turned off automatically due to some problem that was 
probably caused by external digital noise or some other reason. Confirm 
that the POWER/STANDBY indicator is lit red (without flashing). After 
checking the POWER/STANDBY indicator, disconnect the power cord 
from the projector and wait for all of the projector’s indicators to go out. 
Next, reconnect the power cord and turn projector power back on.
If the error occurs again when you turn power back on, contact your 
retailer or nearest authorized CASIO Service Center. LIGHT : –
TEMP : Red steady
Message : –
POWER : Amber flashingJ 
Red steadyThe projector was turned off automatically because the light source unit 
turned off or did not turn on. After confirming that the POWER/STANDBY 
indicator is lit red (without flashing), unplug the power cord. Wait for a 
short while and then plug it back in and turn on the projector again.
If the error occurs again when you turn power back on, contact your 
retailer or nearest authorized CASIO Service Center. LIGHT : Red flashing 
(0.5-second interval)
TEMP : Red flashing 
(0.5-second interval)
Message : –
POWER : Amber flashingJ 
Red steadyPower has turned off automatically due to a projector memory error. 
Confirm that the POWER/STANDBY indicator is lit red (without flashing). 
After checking the POWER/STANDBY indicator, disconnect the power 
cord from the projector and wait for all of the projector’s indicators to go 
out. Next, reconnect the power cord and turn projector power back on.
If the error occurs again when you turn power back on, contact your 
retailer or nearest authorized CASIO Service Center. LIGHT : Not lit or red flashing
TEMP : Red flashing 
(2-second interval)
Message : –
Indicator/Error MessageDescription and Required Action 
						

							42
POWER : Amber flashingJ 
Red steadyPower has turned off automatically because the light source unit cover is 
open. Perform the following steps.
1After confirming that the POWER/STANDBY indicator is lit red (without 
flashing), disconnect the power cord from the projector.
2Check to make sure that the light source unit cover is closed.
3Plug the power cord back in and turn the projector back on again.
If the error occurs again when you turn power back on, contact your 
retailer or nearest authorized CASIO Service Center. LIGHT : –
TEMP : Amber flashing 
(1-second interval)
Message : –
Indicator/Error MessageDescription and Required Action 
						

							43
Appendix
The projector is able to project images from the composite video output, S-video output, or 
component video output of a connected video device.
Important!Always turn off the projector and the video device before connecting them.
Connection to a composite video output or S-video output
NoteNote that regardless of whether the image being projected is being input via the projector’s 
S-VIDEO terminal or VIDEO terminal, the projector outputs audio that is input via the projector’s 
AUDIO IN L/R terminals.
Connecting to a Video Device
To S-video output terminal
To video/audio output terminal
Yellow: To VIDEO terminal To S-VIDEO terminal
Red: To AUDIO IN R terminal
White: To AUDIO IN L terminal
Projector
Video deviceS-video cable (commercially available)
Pin plug type video/audio cable 
(commercially available) 
						

							44
Connection to a component video output
zComponent video output terminals come in 3-terminal sets: Y·Cb·Cr or Y·Pb·Pr. Be sure to match 
the colors of the plugs on a component video cable with the colors of the terminals (Green: Y; 
Blue: Cb/Pb; Red: Cr/Pr).
zNote that connection only to an analog component video output terminal is supported.
Connection to a digital output terminal is not supported.
Projector
AUDIO IN terminal COMPUTER IN terminal
Stereo mini plug 
Ù Pin plug type audio cable 
(commercially available)
Component video cable (commercially available)To component video 
output terminals To AUDIO output
terminals
Video device
Red White
B 
						

							45
The projector supports projection and output of HDMI video and audio output from a computer or 
video device.
Important!Turn off the projector and the computer or video device before connecting them.
zYou will need to obtain a commercially available HDMI cable with a connector that matches the 
terminal of the output device on one end and a connector that matches the projector’s HDMI port 
(HDMI Type A Socket) on the other end.
zFor information about HDMI video signal supported by the projector, see page 54.
zThe projector supports L-PCM 32kHz, 44.1kHz, and 48kHz HDMI audio signals.
Connecting the HDMI Output of a Video Device or 
Computer to the Projector
Projector
HDMI port
To HDMI output terminalComputer or video device
 HDMI cable (commercially available) 
						

							46
When performing an operation on the remote controller, point it at the remote control signal receiver 
on the back or front of the projector. The following illustration shows the range of the remote controller 
signal.
Remote Controller Range
The allowable distance between the remote controller and the projector is less when there is a sharp 
angle between the remote controller and the remote control signal receiver.
Important!To avoid running down the batteries, store the remote control unit so its keys are not pressed 
inadvertently.
Remote Controller Signal Range
Front
±
30 degrees max.
5 meters (16.4 feet) 
max.
5 meters (16.4 feet) max.
Back
5 meters (16.4 feet) 
max.5 meters (16.4 feet) 
max.
±
30 degrees max.±
30 degrees max.
5 degrees to 
30 degrees 
						

							47
The following table shows the relationship between the distance and projected image size.
*h = Height from the center of the lens to the bottom edge of the projection screen.
Important!Note that the distances provided above are for reference only.
Projection Distance and Screen Size
Projection Size
Approximate Projection Distance
XJ-M140/XJ-M145/
XJ-M150/XJ-M155XJ-M240/XJ-M245/
XJ-M250/XJ-M255
Screen 
SizeDiagonal
(cm)Minimum 
Distance
(m / feet)Maximum 
Distance
(m / feet)h*Minimum 
Distance
(m / feet)Maximum 
Distance
(m / feet)h*
(cm / inch)
30 76 1.0 / 3.28 1.5 / 4.92 0 – – –
35 89 – – – 1.0 / 3.28 1.5 / 4.92 8 / 3.15
40 102 1.3 / 4.27 2.0 / 6.56 0 1.1 / 3.61 1.7 / 5.58 9 / 3.54
60 152 2.0 / 6.56 3.0 / 9.84 0 1.7 / 5.58 2.5 / 8.2 13 / 5.12
80 203 2.7 / 8.86 4.0 / 13.12 0 2.3 / 7.55 3.4 / 11.15 18 / 7.09
100 254 3.4 / 11.15 5.0 / 16.4 0 2.9 / 9.51 4.2 / 13.78 23 / 9.06
150 381 5.0 / 16.4 7.4 / 24.28 0 4.3 / 14.11 6.3 / 20.67 34 / 13.39
200 508 6.8 / 22.31 9.9 / 32.48 0 5.8 / 19.03 8.4 / 27.56 45 / 17.72
300 762 10.2 / 33.46 14.9 / 48.88 0 8.7 / 28.54 12.6 / 41.34 67 / 26.38
h* 
						

							48
The following shows how images are projected in accordance with the type of the input signal and the 
aspect ratio setting of the projector.
XJ-M240/XJ-M245/XJ-M250/XJ-M255
Input source: RGB or HDMI (PC)
*The blue boundary indicates the projection area.
Aspect Ratio Setting and Projection Image
Input SignalNormalFullTrue
SVGA (800 × 600)
XGA (1024 × 768)
WXGA (1280 × 800)
SXGA (1280 × 1024)
*
     
						

							49
Input source: Video, S-video, component or HDMI (DTV)
*The blue boundary indicates the projection area.
Input SignalNormal16:9Letter Box
4:3 Aspect Image
*
Squeezed Image
*
Letter Box Image
* 
						

							50
XJ-M140/XJ-M145/XJ-M150/XJ-M155
Input source: RGB or HDMI (PC)
Input SignalNormalFull
SVGA (800 × 600)
XGA (1024 × 768)
WXGA (1280 × 800)
SXGA (1280 × 1024)