Casio Projector XJ-M240 XJ-M245 User Manual
Have a look at the manual Casio Projector XJ-M240 XJ-M245 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 338 Casio manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
31 Screen Settings Main Menu Setting NameInputSetting UnitDescription Keystone Correction RCVHDUNSingle Use this sub-menu to correct vertical keystoning of the projected image. Aspect Ratio RCVHDSource SpecificUse this sub-menu to select an aspect ratio setting for the projected image. Input Source: RGB or HDMI (PC) Normal*: Projects at the projector’s maximum possible size while maintaining the input signal aspect ratio. Full: Projects at the projector’s maximum possible size by enlarging or reducing the input signal. True (XJ-M240/XJ-M245/XJ-M250/XJ-M255 only): Projects the input signal at its actual size (1 input source dot equal to one projector output pixel dot) in the center of the projector’s projection screen. If the input signal resolution exceeds the projector’s output resolution, the excess is cut off. Input Source: Video, S-video, Component or HDMI (DTV) Normal*: Projects at the projector’s maximum possible size while maintaining the input signal aspect ratio. 16:9 : This setting specifies a 16:9 aspect ratio, which is the same as a movie screen, high-definition TV, etc. Using this setting when the input signal is a 16:9 image that has been squeezed to a 4:3 image causes the image to be displayed with its normal 16:9 aspect ratio. Letter Box (XJ-M240/XJ-M245/XJ-M250/XJ-M255 only): This will resize the image horizontally to 1280 dots and project 800 vertical dots of the center of the image, maintaining the aspect ratio of the input signal. NotezWhen the input source is a component or an HDMI (DTV) signal with an aspect ratio of 16:9, the aspect ratio is fixed at 16:9. The aspect ratio setting cannot be changed in this case. zWhen projecting while “True” is selected as the aspect ratio setting for an RGB signal with a resolution that is less than SVGA, the image is enlarged to SVGA and projected. zFor details about projection screen display conditions for different aspect ratio settings, see “Aspect Ratio Setting and Projection Image” (page 48). Important!Note that enlarging or reducing the size of an image for commercial purposes or public presentation may infringe on the legally protected copyright of the copyright holder of the original material. Projection Mode RCVHDUNSingle Use this sub-menu to specify whether projection will be from the front of the screen or the back of the screen. Front*: Select this option to project from the front of the screen. Rear: Select this option to project from the back of the screen. This setting flips the front projected image horizontally.
32 Ceiling MountRCVHDUNSingle Use this sub-menu to configure the projector for use in an installation in which it is positioned upside down. On: Flips the projected image horizontally and vertically. Off*: Projects a normal image. Startup Screen RCVHDUNSingle Use this sub-menu to specify whether or not a startup screen should be projected whenever the projector is turned on. Logo: Select this option to project the projector’s built-in logo screen at startup. None*: Select this option when you do not want to project a startup screen. No Signal Screen RCVHDUNSingle Use this sub-menu to specify what should be projected when there is no input signal to the projector. Blue*: Select this option to project a blue screen. Black: Select this option to project a black screen. Logo: Select this option to project the projector’s built-in logo screen. Blank Screen RCVHDUNSingle Use this sub-menu to specify what should be projected after the [BLANK] key is pressed. Blue: Select this option to project a blue screen. Black*: Select this option to project a black screen. Logo: Select this option to project the projector’s built-in logo screen. Restore Menu Defaults RCVHDUNSource SpecificUse this sub-menu to return all of the sub-menu items on the Screen Settings main menu to their initial default settings. zRestoring menu defaults when there is no input signal will restore defaults for the currently selected input source. zNote that the “Keystone Correction”, “Projection Mode”, “Ceiling Mount”, “Startup Screen”, “No Signal Screen”, and “Blank Screen” settings are always returned to their initial defaults, regardless of the currently selected input source. Setting NameInputSetting UnitDescription
33 Input Settings Main Menu Setting NameInputSetting UnitDescription COMPUTER Terminal RCNSingle Use this sub-menu to specify manually the type of signal being input from the projector’s COMPUTER IN terminal. Auto*: Automatically detects the signal being input from the COMPUTER IN terminal and configures the appropriate input protocol. RGB: Select this option when a computer is connected to the COMPUTER IN terminal. For details about connecting a computer, see “Connecting a Computer to the Projector” in the “Setup Guide”. Component: Select this setting when the projector’s COMPUTER IN terminal is connected to the component video output terminal of a video device using a commercially available component video cable. For information about connection, see “Connecting to a Video Device” (page 43). NoteThe setting of this item cannot be changed while the projector is in the 3D input mode. See “3D Input Mode” on page 10 for information. Video Signal / S-Video Signal VNSingle Use this sub-menu to specify manually the type of signal being input from the projector’s VIDEO terminal or S-VIDEO terminal. Auto*: Select this setting to have the projector switch the video signal system automatically in accordance with the input signal from the video device that is connected to the VIDEO terminal or S-VIDEO terminal. NTSC / NTSC4.43 / PAL / PAL-M / PAL-N / PAL60 / SECAM: Each setting selects the applicable video system. Use these settings when you want to specify only one specific video signal for the VIDEO terminal or S-VIDEO terminal. Signal Name Indicator RCVHDUNSingle Use this sub-menu to specify whether or not the name of the currently selected signal source should be displayed in the projected image. On*: Select this option to turn on display of the name of the currently selected signal source in the projected image. Off: Select this option to turn off display of the signal source name. Restore Menu Defaults RCVHDUNSource SpecificUse this sub-menu to return all of the sub-menu items on the Input Settings main menu to their initial default settings. zRestoring menu defaults when there is no input signal will restore defaults for the currently selected input source. zNote that the “Signal Name Indicator” setting is always returned to its initial default, regardless of the currently selected input source.
34 Option Settings 1 Main Menu Setting NameInputSetting UnitDescription Auto Keystone Correction RCVHDUNSingle Use this sub-menu to turn auto keystone correction on or off. On*: Select this option to turn on auto keystone correction. Off: Select this option to turn off auto keystone correction. Auto Adjust RNSource SpecificUse this sub-menu to select whether the projector should detect the RGB input signal type (resolution, frequency) and adjust the projection image accordingly (auto adjust). 1*: Select this option to turn on auto adjust. 2: Select this option to turn on auto adjust when a 1360 × 768 or 1400 × 1050 signal is not projected correctly. 3: Select this option to turn on auto adjust when a 1366 × 768 signal is not projected correctly. Off: Select this option to turn off auto adjust. Eco Mode RCVHDUNSingle See “Eco Mode (Power Saving, Low Noise)” (page 18). Auto Power Off RCVHDUNSingle Auto Power Off lets you specify the amount of time of projector operation and input signal inactivity to be allowed before Auto Power Off is triggered to turn off projector power automatically. Auto Power Off can be disabled, if you want. 5 min, 10 min*, 15 min, 20 min, 30 min: Time until Auto Power off is triggered. Off: Disables Auto Power Off. Power On Password RCVHDUNSingle You can configure the projector to require input of a password before operation is enabled. For details, see “Password Protecting the Projector” on page 23. Direct Power On RCVHDUNSingle Use this sub-menu to turn Direct Power On on or off. See “Direct Power On” on page 22. On: Select this option to turn on Direct Power On. Off*: Select this option to turn off Direct Power On.
35 Option Settings 2 Main Menu LanguageRCVHDUNSingle Use this sub-menu to specify the language to use for messages, setup menus, etc. English / French / German / Italian / Spanish / Swedish / Portuguese / Turkish / Russian / Chinese (Simplified) / Chinese (Traditional) / Korean / Japanese Note(for USB port model users) If you have Portuguese, Turkish, or Russian selected as the projector’s language, selecting an external device connected to the projector’s USB port as the input source will cause some menus and messages to be displayed in English. Restore Menu Defaults RCVHDUNSingle This sub-menu returns all of the sub-menu items on the Option Settings 1 main menu to their initial default settings. zThe language setting and the password are not returned to their initial factory defaults. zThe “Auto Adjust” item is returned to its initial default only when RGB input is selected for the input source. All of the other items are returned to their initial defaults regardless of the currently selected input source. Setting NameInputSetting UnitDescription Pointer RCVHDUNSingle Use this sub-menu to specify the type of pointer that appears first when you press the [POINTER] key. Plug and Play (USB port models only) RCVHDUNSingle Use this sub-menu to turn plug-and-play*1 on or off. On*: Select this option to turn on plug-and-play. This will allow the projector detect when an external USB device is connected and make that device the input source automatically. Off: Select this option to turn off plug-and-play. NoteRegardless of the setting of this item, plug-and-play is disabled while the projector is in the 3D input mode. See “3D Input Mode” on page 10 for information. Audio Out RCVHDUNSingle Specifies whether the input audio signal should be output from the projector’s built-in speaker or to the line output. Speaker*: Outputs the audio signal being input to the projector from the speaker. Line: Outputs the audio signal being input to the projector from the AUDIO OUT terminal. Setting NameInputSetting UnitDescription
36 High AltitudeRCVHDUNSingle Use this sub-menu to turn the high-altitude fan speed setting on or off in accordance with the altitude of the area where you are using the projector. On: Select this setting when using the projector in a high altitude (1,500 to 3,000 meters above sea level) area where air is thin. This setting increases cooling efficiency. Off*: Select this setting at normal altitudes (up to 1,500 meters). Important!Do not use this projector at altitudes greater than 3,000 meters above sea level. Restore Menu Defaults RCVHDUNSingle This sub-menu returns all of the sub-menu items on the Option Settings 2 main menu to their initial default settings. *1 When plug-and-play is turned on, the projector will make that device the input source automatically. For details about plug-and-play, see “USB Function Guide” on the bundled CD-ROM. Setting NameInputSetting UnitDescription
37 Wired LAN Settings Main Menu (USB Port Models Only) USB Settings Main Menu (USB Port Models Only) The USB Settings main menu is available only when there is an external device connected to the USB port of the projector. For details, see “USB Function Guide” and “Wireless Function Guide” on the bundled CD-ROM. Setting NameInputSetting UnitDescription Remote on RCVHDUNSingle Specifies whether the projector can be turned on via wired LAN while the projector is in standby (projector off with power being supplied). Enable: Power on enabled. Disable*: Power on disabled. Important!Performing an “Initialize Network Settings” operation or “Restore All Defaults” operation with the setup menu will cause this setting to change to “Disable”. If you are operating the projector using a wired LAN setting, be sure to change this setting back to “Enable” after initialization. PJLink authentication RCVHDUNSingle Enables and disables PJLink connection authentication. Enable*: PJLink connection authentication enabled. Disable: PJLink connection authentication disabled. Wired LAN info RCVHDUNSingle Displays the following information. Projector name: Name currently assigned to the projector. MAC Address: Fixed MAC address assigned to each individual projector. IP Address: Projector’s current IP address. DHCP: Projector’s current DHCP setting status (“Auto” or “Disable”). The projector name, IP address, and DHCP settings can be configured using the projector System Admin page, which can be accessed on a computer connected by LAN to the projector. For details, see the “Wireless Function Guide” on the CD-ROM that comes with the projector. Initialize Network Settings RCVHDUNSingle Returns all projector network settings (all settings on the System Admin page) to their initial defaults. For detailed information about System Admin page settings, see the “System Admin Page Settings” section in the “Wireless Function Guide” on the CD-ROM that comes with the projector. B
38 Operational Info Main Menu Restore All Defaults Main Menu Setting NameInputSetting UnitDescription Input Signal RCVHDUNSource SpecificThis sub-menu item shows the currently selected input signal (RGB, Component, Video, S-video, HDMI (PC), or HDMI (DTV)). “- - - -” is indicated here when there is no input signal. Signal Name RCVHDUSource SpecificThis sub-menu item shows the signal name of the signal being input to the projector. For details about signal names, see “Signal Name” under “Supported Signals” on page 52. Resolution RHSource SpecificThis sub-menu item appears only when RGB is the input signal. It shows the number of vertical and horizontal pixels of resolution of the RGB or HDMI (PC) input signal. Horizontal Frequency RCVHDSource SpecificThis sub-menu item shows the horizontal frequency of the input signal. Vertical Frequency RCVHDSource SpecificThis sub-menu item shows the vertical frequency of the input signal. Scan System RCHDSource SpecificThis sub-menu item appears only when RGB, Component, HDMI (PC), or HDMI (DTV) is the input signal, and shows the scan system of the input signal. The scan system is interlace or non-interlace for an RGB or HDMI (PC) signal input, and interlace or progressive for a component or HDMI (DTV) signal input. Light Time RCVHDUNSingle This sub-menu item shows the cumulative number of hours the current light source unit has been used to date. Setting NameInputSetting UnitDescription Unit Operating Time RCVHDUNSingle This sub-menu item shows the cumulative operating time of this unit. This time cannot be initialized. Restore All Defaults RCVHDUNSingle This sub-menu returns all sub-menu items on all main menus to their initial default settings. This operation can be performed regardless of the currently selected input source and regardless of whether or not a signal is currently being input. For details about this procedure, see “To restore all settings on the setup menu to their initial factory defaults” on page 27.
39 Cleaning the Projector Periodically clean the projector exterior, lens, intake vents, exhaust vents, and airflow vents on a regular basis. Important!Before cleaning the projector, be sure to unplug it from the power outlet and make sure it is cooled down completely. Wipe the exterior of the projector with a soft cloth that has been moistened in a weak solution of water and a mild neutral detergent. Be sure to wring all excess moisture from the cloth before wiping. Never use benzene, alcohol, thinner, or any other volatile agent for cleaning. Carefully wipe the lens with a commercially available lens cloth or optical lens paper, like those for eyeglasses or camera lenses. When cleaning the lens, do not apply undue force and take care to avoid damaging the lens. Dust and dirt tend to collect around the intake vents. Because of this, you should use a vacuum cleaner to clean away accumulated dust and dirt periodically as shown below. Important!zContinued use of the projector after dust has accumulated around the intake vents can cause overheating of internal components and lead to malfunction. zCertain operating conditions also can cause dirt and dust to accumulate around the projector’s exhaust vents and airflow vents. If this happens, use the same procedure as that described above to clean the exhaust vents and airflow vents. Cleaning the Projector Exterior Cleaning the Lens Cleaning Intake, Exhaust and Airflow Vents
40 Error Indicators and Warning Messages Warning messages and indicators let you know what the problem is when a projector error occurs. When an error occurs, wait until the fan stops before unplugging the AC power cord. If you unplug the AC power cord while the fan is still operating, an error may occur when you plug the AC power cord back in. Indicator/Error MessageDescription and Required Action POWER : Green steady The projector’s internal temperature is very high. Press the [ESC] key to clear the warning message and perform the following steps. 1Check for any blocking of the projector’s intake vents, exhaust vents and airflow vents, and make sure that there is sufficient space around the projector. See “Setup Precautions” in the “Setup Guide”. 2If there is dust accumulated around the intake vents, exhaust vents and/or airflow vents, turn off the projector and remove it. See “Cleaning the Projector” (page 39). LIGHT : – TEMP : – Message : Internal temperature is too high. Check projector air vents for blockage. POWER : Amber flashingJ Amber steadyPower has turned off automatically due to internal overheating. Perform the following steps. 1Check for any blocking of the projector’s intake vents, exhaust vents and airflow vents, and make sure that there is sufficient space around the projector. See “Setup Precautions” in the “Setup Guide”. 2If there is dust accumulated around the intake vents, exhaust vents and/or airflow vents, remove it. See “Cleaning the Projector” (page 39). If there is no problem with the projector’s vents, confirm that the POWER/ STANDBY indicator is lit amber (without flashing), and then turn power back on again. If the error occurs again when you turn power back on, contact your retailer or nearest authorized CASIO Service Center. LIGHT : – TEMP : – Message : Internal temperature is too high. The projector will turn off. POWER : Amber flashingJ Red steadyPower has turned off automatically due to a fan problem. Confirm that the POWER/STANDBY indicator is lit red (without flashing) and that the fan has stopped. After checking the POWER/STANDBY indicator, disconnect the power cord from the projector and wait for all of the projector’s indicators to go out. Next, reconnect the power cord and turn projector power back on. If the error occurs again when you turn power back on, contact your retailer or nearest authorized CASIO Service Center. LIGHT : Red steady TEMP : Red steady Message : There is a problem with the fan. The projector will turn off. POWER : Amber flashingJ Red steadyPower has turned off automatically due to a system problem. After confirming that the POWER/STANDBY indicator is lit red (without flashing), disconnect the power cord from the projector and wait for all of the projector’s indicators to go out. Next, reconnect the power cord and turn the projector back on. If the error occurs again when you turn power back on, contact your retailer or nearest authorized CASIO Service Center. LIGHT : – TEMP : Red steady Message : A system problem has occurred. The projector will turn off.