Casio Projector XJ-M146 User Manual

							21
Starting Projection of Files Located in Projector Internal 
Memory
1.If a USB flash drive or some other USB device is connected to the projector’s 
USB-A port, disconnect it.
2.Press the [INPUT] key. This will display the “Input” dialog box.
3.Use the [T] and [S] keys to select “Viewer” and then press the [ENTER] key.
4.On the dialog box that appears, confirm that “File Viewer” is selected and then 
press the [ENTER] key.
zThis will start up File Viewer and display the File Viewer main screen like the one shown below.
5.Depending on the type of file you want to project, perform one of the operations 
below.
To project this type of file:Perform this operation:
Presentation Files “To project a presentation file” (page 27)
PDF Files “To project a PDF file” (page 28)
Image Files “To project an image file” (page 29)
Movie Files “To project a movie file” (page 29) 
						

							22
To format projector internal memory
Important!zPerforming the procedure below will delete all of the folders and files currently in the projector 
internal memory.
1.Perform steps 1 through 7 under “To copy files from a computer to projector 
internal memory” (page 19).
2.Perform one of the procedures below to format the “InternalMem” drive on your 
computer.
Windows:
(1) Right click the “InternalMem” drive icon. On the menu that appears, select “Format”.
(2) On the “Format” dialog box that appears, check to make sure that “FAT32 (recommended)” is 
selected for “File system” and then click [Start].
(3) On the warning dialog box that appears, click the [OK] button.
(4) When a dialog box telling you that formatting is complete appears, click [OK] to close it.
(5) Click [Close] to close the format dialog box.
Mac OS:
(1) On the Mac desktop menu bar “Go” menu, select “Utilities” to display the “Utilities” folder.
(2) Double-click “Disk Utility” to start it up.
(3) In the left pane of the disk utility window, click the line above “InternalMem” and then click 
[Erase] at the top of the right pane.
(4) In the “Format” box, select “MS-DOS (FAT)”.
(5) At the bottom of the right pane, select [Erase].
(6) On the warning dialog box that appears, click the [OK] button.
(7) The screen will return to the disk utility window when formatting is complete. Close the 
window. 
						

							23
Projecting Files from a Memory Device Connected by USB
Use the procedures in this section when you want to use File Viewer to project image files, movie files, 
presentation files, or PDF files from a USB flash drive or other memory device.
Supported Memory Devices
The Data Projector’s USB-A port supports connection of a FAT/FAT32 format memory device 
supported by the USB interface. The following are supported memory devices.
zUSB flash drive
zMemory cards
A commercially available USB card reader is required to connect a memory card to the Data 
Projector.
zUSB storage class (USB Mass Storage Class) compatible digital cameras
To connect a USB flash drive to the projector
Connect USB flash drive to the Data Projector’s USB-A port as shown below.
XJ-A Series XJ-M Series 
						

							24
To connect a memory card to the projector
1.Load the memory card into a USB card reader’s card slot.
zFor details about how to load a memory card into the USB card reader, see the user 
documentation that comes with the reader.
2.Connect the USB card reader to the Data Projector’s USB-A port.
To connect a digital camera to the projector
1.If necessary, configure the digital camera’s USB mass storage class setting.
2.Turn off the digital camera and connect a USB cable to it.
3.Connect the other end of the USB cable (Type A connector) to the Data 
Projector’s USB-A port.
4.Turn on the digital camera.
NotezFor details about steps 1, 2, and 4, see the user documentation that comes with your digital 
camera.
XJ-A Series
XJ-M Series 
						

							25
To start projection of files that are on a memory device 
connected via USB
1.Connect the memory device where files you want to project are stored to the 
projector’s USB-A port.
zIf the File Viewer main screen appears automatically, advance to step 5 of this procedure. If it 
doesn’t, go to step 2. Note that the File Viewer main screen will appear automatically if “On” is 
selected for the “Plug and Play” setting on the projector’s Setup Menu.
2.Press the [INPUT] key. This will display the “Input” dialog box.
3.Use the [T] and [S] keys to select “Viewer” and then press the [ENTER] key.
4.On the dialog box that appears, confirm that “File Viewer” is selected and then 
press the [ENTER] key.
zThis will start up File Viewer and display the File Viewer main screen.
5.Depending on the type of file you want to project, perform one of the operations 
below.
zThe screen that will appear depends on the function you selected.
6.Use the file list displayed on the screen to check the contents of the USB flash 
drive you connected in step 1 of this procedure or the contents of internal 
memory.
zIf the file list shows the contents of a USB flash drive, go to step 8 of this procedure. If the file 
list shows the contents of internal memory, go to step 7.
7.Press the [FUNC] key. On the menu that appears, select “Drive Switching” and 
then press the [ENTER] key.
To project this type of file:Perform this operation:
Presentation File Use the [T] and [S] keys to select “Presentation” and then press the [ENTER] 
key.
PDF File Use the [T] and [S] keys to select “PDF Viewer” and then press the [ENTER] 
key.
Image File Use the [T] and [S] keys to select “Slide” and then press the [ENTER] key.
Movie File Use the [T] and [S] keys to select “Movie” and then press the [ENTER] key.
Function nameFolder path 
						

							26
8.Depending on the function you selected in step 5 of this procedure, perform one 
of the operations below.
Drive Menu
Entering the Presentation Mode, PDF Viewer Mode, Slide Mode, or Movie Mode while there are 
multiple memory devices connected to the Data Projector’s USB-A port (multiple USB flash drive 
devices connected via a USB hub, multiple memory cards loaded in the memory card reader 
connected to the Data Projector, etc.) will cause a menu like the one shown below to appear on the 
projection screen.
When this happens, use the cursor keys to move the highlighting to the drive you want to use and then 
press the [ENTER] key. This will display a menu of files for the mode you are entering.
NotezThe Data Projector can recognize up to four drives.
zThe message “NOUSB” will appear in the Drive Menu if there is no memory device connected 
to the projector’s USB-A port when you perform Drive Switching ([FUNC] 3 “Drive 
Switching” 3 [ENTER]). If this happens, perform Drive Switching again to restore the 
previous screen.
If you selected this function:Perform this operation:
Presentation Perform the procedure from step 2 under “To project a presentation file” 
(page 27).
PDF Viewer Perform the procedure from step 2 under “To project a PDF file” (page 28).
Slide Perform the procedure from step 2 under “To project an image file” (page 
29).
Movie Perform the procedure from step 2 under “To project a movie file” (page 29). 
						

							27
Projecting Files
This section explains procedures you can project each type of file using File Viewer.
To project a presentation file
1.On the File Viewer main screen, select “Presentation” and then press the 
[ENTER] key.
zThis displays a menu of presentation (ECA or PtG) files.
2.Use the [T] and [S] keys to select the presentation file you want to play and then 
press the [ENTER] key (or [ ] key).
zThis will start playback of the currently selected presentation file.
3.Perform page change and other operations as required.
zYou can perform the operations described in the table below while presentation playback is in 
progress.
4.To return to the file menu, press the [ESC] key.
5.To return to the main screen, press the [FUNC] key and then the [ENTER] key.
To do this:Perform this operation:
Go to the previous page Press the [W] or [ ] key.
Go to the next page Press the [X] or [ ] key.
Pause playback Press the [ ] key.
Resume playback from where it 
was pausedPress the [ ] key.
Move back to the position of the 
previous animation delimiterPress the [S] or [ ] key
Move forward to the position of 
the next animation delimiterPress the [T] or [ ] key.
Select a particular page from a 
menu of thumbnails and play back 
that page1. Press the [FUNC] key.
2. On the menu that appears, select “Page Selection” and then press 
the [ENTER] key.
3. Use the cursor keys to select the thumbnail of the page you want 
to play back and then press the [ENTER] key. 
						

							28
To project a PDF file
1.On the File Viewer main screen, select “PDF Viewer” and then press the [ENTER] 
key.
zThis displays a list of PDF files.
2.Use the [T] and [S] keys to select the PDF file you want to open and then press 
the [ENTER] key (or [ ] key).
zThis will open the selected PDF file.
3.Perform page change, zoom, and other operations as required.
zThe following operations are supported during PDF file projection.
4.To return to the file menu, press the [ESC] key.
5.To return to the main screen, press the [FUNC] key and then the [ENTER] key.
To do this:Perform this operation:
Go to the previous page Press the [W] or [ ] key.
Go to the next page Press the [X] or [ ] key.
Adjust the image to the 
screen widthPress the [FUNC] key. On the menu that appears, select “Adjust to Screen 
Width” and then press the [ENTER] key.
Return to a full page view Press the [FUNC] key. On the menu that appears, select “Show Entire 
Page” and then press the [ENTER] key.
Select a page from a 
thumbnail list and display it1. Press the [FUNC] key.
2. On the menu that appears, select “Page Selection” and then press the 
[ENTER] key.
3. Use the cursor keys to select the thumbnail of the page you want to 
display and then press the [ENTER] key. 
						

							29
To project an image file
1.On the File Viewer main screen, select “Slide” and then press the [ENTER] key.
zThis displays a list of image files.
2.Use the [T] and [S] keys to select image file you want to open and then press 
the [ENTER] key.
zThis will project the selected image file.
zPressing the [ ] key instead of the [ENTER] key will start an image file slideshow starting 
from the currently selected file.
3.Perform the rotate image and image scrolling operations described below as 
required.
zThe following operations are supported during image file projection.
*Supported for JPEG files only.
4.To return to the file menu, press the [ESC] key.
5.To return to the main screen, press the [FUNC] key and then the [ENTER] key.
To project a movie file
1.On the File Viewer main screen, select “Movie” and then press the [ENTER] key.
zThis displays a list of movie files.
2.Use the [T] and [S] keys to select the movie file you want to open and then 
press the [ENTER] key or [ ] key.
zThis will start playback of the selected movie file.
To do this:Perform this operation:
Project the previous image file Press the [W] or [ ] key.
Project the next image Press the [X] or [ ] key.
Rotate the image leftwards 90 degrees*Press the [ ] key.
Rotate the image rightwards 90 degrees*Press the [ ] key.
Start a slideshow Press the [ ] key.
Stop an ongoing slideshow Press the [ ] key. 
						

							30
3.Perform fast forward, fast reverse, pause, and other operations as required.
zThe operations described below are supported during movie file playback.
4.To return to the file menu, press the [ESC] key.
5.To return to the main screen, press the [FUNC] key and then the [ENTER] key.
To do this:Perform this operation:
Pause and resume movie playback Press the [ENTER] or [ ] key.
zA pause icon ( ) is displayed in the upper left 
corner of the projection screen while movie 
projection is paused.
Re-play the file from the beginning 1. Press the [FUNC] key.
2. On the menu that appears, select “Play from 
Beginning” and then press the [ENTER] key.
Toggle display of the movie playback time 
between show and hidePress the [FUNC] key. On the menu that appears, 
select “Time Indicator On/Off” and then press the 
[ENTER] key.
Fast forward at 2X, 8X, or 32X normal speed Press the [X] or [ ] key.
zThe first press starts 2X speed fast forward, the 
second press increases to 8X, and the third press 
increases to 32X.
zThe   indicator appears in the upper left corner 
during 2X fast forward,   during 8X fast forward, 
and   during 32X fast forward.
Fast reverse at 2X, 8X, or 32X normal speed Press the [W] or [ ] key.
zThe first press starts 2X speed fast reverse, the 
second press increases to 8X, and the third press 
increases to 32X.
zThe   indicator appears in the upper left corner 
during 2X fast reverse,   during 8X fast reverse, 
and   during 32X fast reverse.
Return from fast forward or fast reverse to 
normal playbackPress the [ENTER] key or [ ] key twice. Pressing 
either of these keys only once will pause playback. 
Press once more to start normal playback.
Jump to the final movie frame Press the [FUNC] key. On the menu that appears, 
select “Go to End” and then press the [ENTER] key.
Stop movie file playback and return to the file 
menuPress the [ESC] key.
Total movie play time
Elapsed movie play time