Home > Casio > Projector > Casio Projector XJ-M141 User Manual

Casio Projector XJ-M141 User Manual

Here you can view all the pages of manual Casio Projector XJ-M141 User Manual. The Casio manuals for Projector are available online for free. You can easily download all the documents as PDF.

Page 11

11
Connect the projector to a power outlet and to an input source device.
XJ-A Series
XJ-M Series
NotezFor more information about component video connection, see “Connecting to a Component 
Video Output” on page 72.
zFor information about how to connect for RS-232C control of the projector, see “Projector 
RS-232C Control” (page 83).
zFor information about how to connect in order to update the projector firmware or to transfer 
user logo data, see “Updating Firmware and Transferring a User Logo” (page...

Page 12

12
Projector operations are performed using the remote controller that comes with it. Point the remote 
controller signal emitter at one of the signal receivers on the projector as you perform remote 
controller key operations. The maximum range of the remote controller signal is approximately 
5 meters (16.4 feet) (between signal emitter and receiver).
Important!zTo avoid running down the battery, store the remote control unit so its keys are not pressed 
inadvertently.
Remote Controller
1Remote control...

Page 13

13
To load remote controller batteries
Important!zBe sure to use alkaline batteries only.
To replace remote controller batteries
Open the battery cover on the back of the remote controller, replace the old batteries with new ones, 
and then close the battery cover.
*CautionRISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
1.Open the battery cover on the back 
of the remote controller.2.Load two new batteries into the 
case, making sure...

Page 14

14
Projecting an Image
This section provides information about how to project images from various different input sources.
Input source selection provides the options described in the table below.
Selecting the Input Source
Input Source NameOutput Projection Image (and Audio)
Computer Screen image of a computer connected to the projector’s computer terminal.
Video XJ-A Series: Images and audio from a video device connected to the projector’s AV 
terminal.
XJ-M Series: Images and audio from a video device...

Page 15

15
To select the input source
1.Press the [INPUT] key. This will display the “Input” dialog box.
2.Depending on the input source, perform one of the operations described in the 
table below.
zThe name of the input source you selected will appear in the upper right corner of the 
projection screen for a few seconds.
zThe message “No signal input” will appear if no input signal can be detected.
NotezFor more information about the operation required to select Wireless, Network, USB Display, 
File Viewer, or...

Page 16

16
Your projector supports projection of 3D images. To project a 3D image, first enter the projector’s 3D 
input mode, and then select the input source.
Important!zSeparately available 3D glasses (YA-G30) are required in order to view a projected 3D image in 
3D.
zSeparately available special software (CASIO 3D Converter) is required to project a 3D image 
with the projector when a computer (analog RGB) is the input source.
z3D image projection is not supported via an HDMI connection or component video...

Page 17

17
Returning to the Normal Input Mode from the 3D Input Mode
1.Press the [INPUT] key to display the input source selection screen.
2.Use the [T] and [S] keys to move the highlighting to “To normal input mode” 
and then press the [ENTER] key.
zThis enters the normal input mode and closes the input source selection screen.
Horizontal Flipping in the 3D Input Mode
In side-by-side 3D, a full frame consists of two halves on the left and right for each eye. In rare cases, 
the left and right images may be...

Page 18

18
File Viewer Overview
File Viewer is an application you can use for viewing or playing back different types of files located in 
projector internal memory or on a memory device connected to the projector’s USB port.
Supported Playback Files
Projecting Files Located in Projector Internal Memory
File Viewer can be used to project the following types of files when they are located in projector 
internal memory: image files, movie files, presentation files, PDF files. To use the procedure in this 
section,...

Page 19

19
To copy files from a computer to projector internal memory
NotezThis procedure is supported on a computer running one of the operating systems below.
Windows: XP, Vista, 7, 8, 8.1 (Logged in with admin privileges)
Mac OS: 10.6, 10.7, 10.8, 10.9 (Logged in with a root account or user account)
1.Press the [MENU] key to display the setup menu.
2.Use the [T] key to select “Multimedia Settings”, and then press the [ENTER] key.
3.Use the [T] key to select “Internal Storage Function”, and then press the...

Page 20

20
10.After you copy all of the files you want, perform one of the operations below to 
unmount the “InternalMem” drive.
11.Disconnect the USB cable from the projector and the computer.
12.Turn the projector back on.
zThis stops internal storage function operation and returns to normal projection.
zFor information about how to project a file copied to projector internal memory, see “Starting 
Projection of Files Located in Projector Internal Memory” (page 21).
NotezThe above is presented only as a...
Start reading Casio Projector XJ-M141 User Manual

Related Manuals for Casio Projector XJ-M141 User Manual

All Casio manuals