Casio Projector XJ-H1600 XJ-H1650 User Manual
Have a look at the manual Casio Projector XJ-H1600 XJ-H1650 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 338 Casio manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
41 Error Indicators and Warning Messages Warning messages and indicators let you know what the problem is when a projector error occurs. When an error occurs, wait until the fan stops before unplugging the AC power cord. If you unplug the AC power cord while the fan is still operating, an error may occur when you plug the AC power cord back in. Indicator/Error MessageDescription and Required Action POWER : Green steady The projector’s internal temperature is very high. Press the [ESC] key to clear the warning message and perform the following steps. 1Check for any blocking of the projector’s vents, and make sure that there is sufficient space around the projector. See “Setup Precautions” in the “Setup Guide”. 2If there is dust accumulated around the vents, turn off the projector and remove it. See “Cleaning the Projector” (page 40). LIGHT : – TEMP : – Message : Internal temperature is too high. Check projector air vents for blockage. POWER : Amber flashingJ Amber steadyPower has turned off automatically due to internal overheating. Perform the following steps. 1Check for any blocking of the projector’s vents, and make sure that there is sufficient space around the projector. See “Setup Precautions” in the “Setup Guide”. 2If there is dust accumulated around the vents, remove it. See “Cleaning the Projector” (page 40). If there is no problem with the projector’s vents, confirm that the POWER/ STANDBY indicator is lit amber (without flashing), and then turn power back on again. If the error occurs again when you turn power back on, contact your retailer or nearest authorized CASIO Service Center. LIGHT : – TEMP : – Message : Internal temperature is too high. The projector will turn off. POWER : Amber flashingJ Red steadyPower has turned off automatically due to a fan problem. Confirm that the POWER/STANDBY indicator is lit red (without flashing) and that the fan has stopped. After checking the POWER/STANDBY indicator, disconnect the power cord from the projector and wait for all of the projector’s indicators to go out. Next, reconnect the power cord and turn projector power back on. If the error occurs again when you turn power back on, contact your retailer or nearest authorized CASIO Service Center. LIGHT : Red steady TEMP : Red steady Message : There is a problem with the fan. The projector will turn off. POWER : Amber flashingJ Red steadyPower has turned off automatically due to a system problem. After confirming that the POWER/STANDBY indicator is lit red (without flashing), disconnect the power cord from the projector and wait for all of the projector’s indicators to go out. Next, reconnect the power cord and turn the projector back on. If the error occurs again when you turn power back on, contact your retailer or nearest authorized CASIO Service Center. LIGHT : – TEMP : Red steady Message : A system problem has occurred. The projector will turn off.
42 POWER : Green steady A system problem has occurred, which may cause problems with some functions. Turn off the projector, disconnect the power cord from the projector and wait for all of the projector’s indicators to go out. Next, reconnect the power cord and turn the projector back on. If the error occurs again when you turn power back on, contact your retailer or nearest authorized CASIO Service Center. Press the [ESC] key to clear the warning message. LIGHT : – TEMP : – Message : A system problem has occurred. Normal projection is not possible. POWER : Green steady LIGHT : – TEMP : – Message : There is some problem with the system. The audio function may not operate correctly. POWER : Green steady The USB or LAN connection was terminated because of a problem with the USB port or LAN port. To use the USB or LAN function, turn off the projector and then turn it back on again. If the error occurs again when you turn power back on, contact your retailer or nearest authorized CASIO Service Center. Press the [ESC] key to clear the warning message. LIGHT : – TEMP : – Message : Some problem occurred with the USB port or LAN terminal. POWER : Amber flashingJ Red steadyThe projector was turned off automatically due to some problem that was probably caused by external digital noise or some other reason. Confirm that the POWER/STANDBY indicator is lit red (without flashing). After checking the POWER/STANDBY indicator, disconnect the power cord from the projector and wait for all of the projector’s indicators to go out. Next, reconnect the power cord and turn projector power back on. If the error occurs again when you turn power back on, contact your retailer or nearest authorized CASIO Service Center. LIGHT : – TEMP : Red steady Message : – POWER : Amber flashingJ Red steadyThe projector was turned off automatically because the light source unit turned off or did not turn on. After confirming that the POWER/STANDBY indicator is lit red (without flashing), unplug the power cord. Wait for a short while and then plug it back in and turn on the projector again. If the error occurs again when you turn power back on, contact your retailer or nearest authorized CASIO Service Center. LIGHT : Red flashing (0.5-second interval) TEMP : Red flashing (0.5-second interval) Message : – POWER : Amber flashingJ Red steadyPower has turned off automatically due to a projector memory error. Confirm that the POWER/STANDBY indicator is lit red (without flashing). After checking the POWER/STANDBY indicator, disconnect the power cord from the projector and wait for all of the projector’s indicators to go out. Next, reconnect the power cord and turn projector power back on. If the error occurs again when you turn power back on, contact your retailer or nearest authorized CASIO Service Center. LIGHT : Not lit or red flashing TEMP : Red flashing (2-second interval) Message : – Indicator/Error MessageDescription and Required Action
43 POWER : Amber flashingJ Red steadyPower has turned off automatically because the light source unit cover is open. Perform the following steps. 1After confirming that the POWER/STANDBY indicator is lit red (without flashing), disconnect the power cord from the projector. 2Check to make sure that the light source unit cover is closed. 3Plug the power cord back in and turn the projector back on again. If the error occurs again when you turn power back on, contact your retailer or nearest authorized CASIO Service Center. LIGHT : – TEMP : Amber flashing (1-second interval) Message : – Indicator/Error MessageDescription and Required Action
44 Appendix The projector is able to project images from the composite video output, S-video output, or component video output of a connected video device. Important!Always turn off the projector and the video device before connecting them. Connection to a composite video output or S-video output NoteNote that regardless of whether the image being projected is being input via the projector’s S-VIDEO terminal or VIDEO terminal, the projector outputs audio that is input via the projector’s AUDIO IN L/R terminals. Connecting to a Video Device To S-video output terminal To video/audio output terminal Yellow: To VIDEO terminal To S-VIDEO terminal Red: To AUDIO IN R terminal White: To AUDIO IN L terminal Projector Video device S-video cable (commercially available) Pin plug type video/audio cable (commercially available)
45 Connection to a component video output zComponent video output terminals come in 3-terminal sets: Y·Cb·Cr or Y·Pb·Pr. Be sure to match the colors of the plugs on a component video cable with the colors of the terminals (Green: Y; Blue: Cb/Pb; Red: Cr/Pr). zNote that connection only to an analog component video output terminal is supported. Connection to a digital output terminal is not supported. Projector AUDIO IN 1 terminal COMPUTER IN 1 terminal Stereo mini plug Ù Pin plug type audio cable (commercially available) Component video cable (commercially available) To component video output terminals To AUDIO output terminals Video device Red White AUDIO IN 2 terminalCOMPUTER IN 2 terminal
46 The projector supports projection and output of HDMI video and audio output from a computer or video device. Important!Turn off the projector and the computer or video device before connecting them. zYou will need to obtain a commercially available HDMI cable with a connector that matches the terminal of the output device on one end and a connector that matches the projector’s HDMI port (HDMI Type A Socket) on the other end. zFor information about HDMI video signal supported by the projector, see page 54. zThe projector supports L-PCM 32kHz, 44.1kHz, and 48kHz HDMI audio signals. Connecting the HDMI Output of a Video Device or Computer to the Projector Projector HDMI port To HDMI output terminal Computer or video device HDMI cable (commercially available)
47 When performing an operation on the remote controller, point it at the remote control signal receiver on the back or front of the projector. The following illustration shows the range of the remote controller signal. Remote Controller Range The allowable distance between the remote controller and the projector is less when there is a sharp angle between the remote controller and the remote control signal receiver. Important!To avoid running down the batteries, store the remote control unit so its keys are not pressed inadvertently. Remote Controller Signal Range Front ± 30 degrees max. 5 meters (16.4 feet) max. 5 meters (16.4 feet) max. Back 5 meters (16.4 feet) max.5 meters (16.4 feet) max. ± 30 degrees max.± 30 degrees max. 5 degrees to 30 degrees
48 The projector can be hung from a ceiling. When doing so, the projector should be turned upside down, and secured to the ceiling. You also need to install a safety wire to ensure that the projector cannot fall accidentally. To attach the safety wire, remove the sticker on the bottom of the projector and attach the wire there. For full details, contact the retailer where you purchased the projector. Important!zWhen hanging the projector from a ceiling, make sure that it is at least one meter away from fire detectors, fire alarms, and other fire protection devices. Locating the projector too close to a fire protection device creates the risk of mis-operation of the device due to warm air exhausted from the projector. Also, avoid locating the projector close to fluorescent lights or other strong light sources. Bright light can shorten the operating range of the remote controller or even make remote control impossible. When selecting a location for the projector, be sure to test for proper operation of the remote controller. zThe vertical and horizontal orientation of the projected image is reversed from the normal configuration when projecting from a projector hung from the ceiling. You need to change the setup of the projector in order to correct for this. For details, see the “Ceiling Mount” option under “Screen Settings Main Menu” (page 32). Hanging the Projector from a Ceiling Sticker
49 The following table shows the relationship between the distance and projected image size. *h = Height from the center of the lens to the bottom edge of the projection screen. Important!Note that the distances provided above are for reference only. Projection Distance and Screen Size XJ-H1600/XJ-H1650/XJ-H1700/XJ-H1750 XJ-ST145/XJ-ST155 Projection SizeApproximate Projection DistanceProjection SizeApproximate Projection Distance (m / feet) h* (cm / inch)Screen SizeDiagonal (cm)Minimum Distance (m / feet)Maximum Distance (m / feet)h*Screen SizeDiagonal (cm) 27 69 0.85/2.79 1.0/3.28 0 45 114 0.6/1.97 6/2.36 40 102 1.3/4.27 1.6/5.25 0 60 152 0.8/2.62 8/3.15 60 152 1.9/6.23 2.3/7.55 0 80 203 1.1/3.61 10/3.94 80 203 2.6/8.53 3.1/10.17 0 100 254 1.4/4.59 13/5.12 100 254 3.3/10.83 3.9/12.8 0 142 361 2.0/6.56 19/7.48 150 381 4.9/16.08 5.9/19.36 0 200 508 6.6/21.65 7.9/25.92 0 300 762 9.9/32.48 11.9/39.04 0 h* D
50 The following shows how images are projected in accordance with the type of the input signal and the aspect ratio setting of the projector. Input source: RGB or HDMI (PC) Aspect Ratio Setting and Projection Image Input SignalNormalFull SVGA (800 × 600) XGA (1024 × 768) WXGA (1280 × 800) SXGA (1280 × 1024)