Casio Projector XJ-F10X User Manual

							61
Connecting the projector to a computer with a USB cable* enables projection of the computer’s 
screen contents. This supports projection of screen contents of even small computers that have only a 
USB port, but no RGB, HDMI, or other type of video output terminal.
*To use the USB Display function, connect the computer to the projector’s USB-B port.
Minimum Computer System Requirements
Supported Operating Systems
Windows XP SP3, Windows Vista SP1 (32bit), Windows 7 SP1 (32bit, 64bit), Windows 8/8.1 (64bit), 
Windows 10, or Mac OS (10.6, 10.7, 10.8, 10.9)
Note, however, that functions may be limited by the operating system being used. For the latest 
information about operating environments, visit the CASIO website.
USB Type A port (USB 2.0 or USB 3.0) equipped.
Important!Log into Windows with admin privileges to use the USB display function. You will not be able 
to use USB display if you are logged into Windows with a non-admin account.
The operation you need to perform the first time you connect to a computer to project its display 
contents (described below) depends on whether the computer is running Windows or Mac OS. After 
that, use the procedure under “To project computer screen contents over a USB connection after the 
first time” (page 65), which is the same for any operating system.
Perform one of the procedures below, depending on your computer’s operating system.
Projecting with the USB Display Function
USB Display Function Overview
Projecting Computer Screen Contents Over a USB Connection 
						

							62
To project Windows computer screen contents over a USB 
connection for the first time
1.Press the [INPUT] key. This will display the “Input” dialog box.
2.Use the [] and [] keys to select “USB Display” and then press the [ENTER] 
key.
This will cause the “USB Display” standby screen to be projected.
3.While your computer is running, use a commercially available USB cable to 
connect the projector’s USB-B port (Micro USB B type) to your computer’s USB 
port.
The location of the USB-B port of this projector is indicated by “*2” in the illustration under 
“Connecting Projector Cables” (page 11).
This will mount the projector onto your computer as a virtual CD-ROM drive, which is 
represented by a “USB_DISPLAY” drive icon on your computer’s desktop.
Also, CASIO USB Display will start up automatically and display a licensing agreement dialog 
box.
4.On the licensing agreement dialog box, select “I agree” and then click [OK].
This will display a window like the one shown below on your computer. At the same time, 
projection of the computer’s screen contents will start.
NoteIf CASIO USB Display does not start up automatically, use Explorer to navigate to the 
“USB_DISPLAY” drive. Right-click the drive and then click “Auto Play” on the menu that 
appears.
For information about the types of operations that can be performed at this point, see 
“Supported Operations during Projection over a USB connection” (page 64).
Add-on Driver Software for Windows
With Windows, use of some functions of the CASIO USB Display requires installation of the driver 
software shown in the table below. The driver software is the same as that used for Network 
Connection. You can download it from the Network Connection download page at the CASIO website 
(http://www.casio-intl.com/support/).
To use this function:Install this driver software:
Extended screen output function VDD driver (for Windows XP and Windows Vista) 
						

							63
To project Mac OS computer screen contents over a USB 
connection for the first time
1.Press the [INPUT] key. This will display the “Input” dialog box.
2.Use the [] and [] keys to select “USB Display” and then press the [ENTER] 
key.
This will cause the “USB Display” standby screen to be projected.
3.While your computer is running, use a commercially available USB cable to 
connect the projector’s USB-B port to your computer’s USB port.
The location of the USB-B port of this projector is indicated by “*2” in the illustration under 
“Connecting Projector Cables” (page 11).
This will cause a drive icon named “USB_DISPLAY” to appear on your computer screen.
4.Double-click the “USB_DISPLAY” drive icon to open it.
5.Double-click “MAC_USB_Display_V2.pkg” and follow the instructions that 
appear on the display to install the application.
A message prompting you to restart your computer will appear after installation is complete. 
Restart your computer. After the restart is complete, you will see a CASIO USB Display icon in 
the Dock.
6.In the Dock, click the CASIO USB Display icon.
Also, CASIO USB Display will start up and display a licensing agreement dialog box.
7.On the licensing agreement dialog box, select “I agree” and then click [OK].
This will display a window like the one shown below on your computer. At the same time, 
projection of the computer’s screen contents will start.
For information about the types of operations that can be performed at this point, see 
“Supported Operations during Projection over a USB connection” (page 64).
Add-on Driver Software for Mac OS
With Mac OS, use of some parts of the CASIO USB Display requires installation of the driver software 
shown in the table below. The driver software is the same as that used for Network Connection. You 
can download it from the Network Connection download page at the CASIO website 
(http://www.casio-intl.com/support/).
To use this function:Install this driver software:
Audio output function Sound flower
Extended desktop output function Syphon-virtual-screen 
						

							64
Supported Operations during Projection over a USB connection
The operations described in the table below are supported on the CASIO USB Display window during 
projection.
To do this:Perform this operation:
Start (resume) computer screen projection
Click .
Freeze computer screen projection
Click .
Stop computer screen projection and project the USB 
display standby screenClick .
Start audio output from a computer*
1Click  . On the menu that appears, select “Audio 
Out” so there is a check mark next to it.
Mute audio output from a computer*
1Click  . On the menu that appears, select “Audio 
Out” to remove the check mark next to it.
Output the computer’s main screen on the projection 
screenClick  . On the menu that appears, select “Select the 
Projection Screen” 3 “Main Screen”.
Output the computer’s extended screen on the 
projection screen*
1*2Click  . On the menu that appears, select “Select the 
Projection Screen” 3 “Extended Screen”.
Minimize the CASIO USB Display window Click  .
Exit the CASIO USB Display window (1) Click  . Or you could click   and then click 
“Exit” on the menu that appears.
(2) On the confirmation dialog box that appears, click 
the [OK] button.
This stops computer screen projection and 
projects the “USB Display” standby screen.
Display CASIO USB Display version information Click  . On the menu that appears, select “About”.
*1 With Mac, installation of driver software is required to enable these functions. See “Add-on Driver 
Software for Mac OS” (page 63).
*2 This operation is disabled under Mac OS 10.6. With Windows XP and Windows Vista, installation of 
driver software is required to enable these functions. See “Add-on Driver Software for Windows” 
(page 62). 
						

							65
To project computer screen contents over a USB connection 
after the first time
1.Turn on and start up the projector and computer.
2.Press the [INPUT] key. This will display the “Input” dialog box.
3.Use the [] and [] keys to select “USB Display” and then press the [ENTER] 
key.
This will cause the “USB Display” standby screen to be projected.
4.Use a USB cable to connect the projector’s USB-B port to your computer’s USB 
port.
The CASIO USB Display will startup automatically on the computer and start projection of the 
computer screen contents.
NoteIf the above operation does not cause CASIO USB Display to start up automatically, perform 
either of the operations below on your computer, depending on its operating system.
Windows:
Use Explorer to navigate to the “USB_DISPLAY” drive. Right-click the drive and then click 
“Auto Play” on the menu that appears.
Mac OS:
In the Dock, click the CASIO USB Display icon. 
						

							66
You can connect a CASIO graphing calculator to the Data Projector using a USB cable and project the 
calculator’s screen image with the Data Projector. USB connection of the following CASIO graphing 
calculators is supported.
ClassPad II (fx-CP400)
ClassPad 330 PLUS
fx-CG series
fx-9860G series
fx-9860GII series
fx-9750GII
GRAPH 95/85/85 SD/75/75+/35+
To project the screen image of a graphing calculator
1.While the projector is turned on, connect the USB cable that comes with the 
graphing calculator to the projector’s USB-A port and the graphing calculator’s 
USB port.
2.On the projector, press the [INPUT] key. This will display the “Input” dialog box.
3.Use the [] and [] keys to select “CASIO USB Tool” and then press the 
[ENTER] key.
4.On the graphing calculator, perform the operation required for projection.
For details about this operation, refer to the use documentation that comes with your 
calculator.
Important!If the calculator does not operate properly after you connect it to the Data Projector, try 
disconnecting the USB cable from the calculator and then reconnecting it. If this does not 
correct the problem, disconnect the USB cable from both the Data Projector and the 
calculator. Turn the Data Projector off and then back on again, and then re-connect the 
calculator.
Projecting the Screen Image of a Graphing Calculator 
						

							67
Cleaning the Projector
Make it a habit to clean the projector at regular intervals as described in this section. Before cleaning 
the projector, be sure to unplug it from the power outlet and make sure it is cooled down completely.
Wipe the exterior of the projector with a soft cloth that has been moistened in a weak solution of water 
and a mild neutral detergent. Be sure to wring all excess moisture from the cloth before wiping.
Never use benzene, alcohol, thinner, or any other volatile agent for cleaning.
Carefully wipe the lens with a commercially available lens cloth or optical lens paper, like those for 
eyeglasses or camera lenses. When cleaning the lens, do not apply undue force and take care to avoid 
damaging the lens.
Dust and dirt tend to collect around the intake vents. Because of this, you should use a vacuum 
cleaner to clean away accumulated dust and dirt periodically (about once a month) as shown below.
Important!Continued use of the projector after dust has accumulated around the intake vents can cause 
overheating of internal components and lead to malfunction.
Certain operating conditions also can cause dirt and dust to accumulate around the 
projector’s exhaust vents. If this happens, use the same procedure as that described above to 
clean the exhaust vents.
Cleaning the Projector Exterior
Cleaning the Lens
Cleaning Vents 
						

							68
Troubleshooting
The POWER/STANDBY indicator and STATUS indicator change to show the current status of the 
projector as described in the tables below.
POWER/STANDBY indicator
STATUS indicator
NoteThe POWER/STANDBY and STATUS indicators both light amber immediately after the 
projector is plugged into a power outlet.
Indicators
When the indicator is doing this:It means this about the projector:
Lit red Connected to a power source, but turned off (standby mode)
Flashing green Warming up after being turned on
Lit green Power on, operation normal
Flashing red Internal process in progress immediately after power off
When the indicator is doing this:It means this about the projector:
Lit green “On” selected for the “Light Control” setting
Lit (or flashing) red Error
Lit (or flashing) amber Error 
						

							69
Warning messages and indicators let you know what the problem is when a projector error occurs.
When an error occurs, wait until the fan stops before unplugging the AC power cord. If you unplug 
the AC power cord while the fan is still operating, an error may occur when you plug the AC power 
cord back in.
Press the [ESC] key to clear the warning message.
Error Indicators and Warning Messages
Indicator/Error MessageDescription and Required Action
POWER : Green steady The projector’s internal temperature is very high. Perform the following 
steps.
Check for any blocking of the projector’s intake vents and exhaust 
vents, and make sure that there is sufficient space around the 
projector. See 
“Setup Precautions” (page 10).
If there is dust accumulated around the intake vents and/or exhaust 
vents, turn off the projector and remove it. See 
“Cleaning the 
Projector” (page 67). STATUS : –
(Green steady when “On” 
is selected for the “Light 
Control” setting.)
Message : Internal temperature is too 
high. Check projector air 
vents for blockage.
POWER : Green steady 3
Red steadyPower has turned off automatically due to internal overheating. Perform 
the following steps.
Check for any blocking of the projector’s intake vents and exhaust 
vents, and make sure that there is sufficient space around the 
projector. See 
“Setup Precautions” (page 10).
If there is dust accumulated around the intake vents and/or exhaust 
vents, remove it. See 
“Cleaning the Projector” (page 67).
If there is no problem with the projector’s vents, confirm that the POWER/
STANDBY indicator is lit red (without flashing), and then turn power back 
on again. If the error occurs again when you turn power back on, contact 
your retailer or nearest authorized CASIO Service Center. STATUS : –
Message : Internal temperature is too 
high. The projector will 
turn off.
POWER : Red steady Power has turned off automatically due to a fan problem. Confirm that the 
POWER/STANDBY indicator is lit red (without flashing) and that the fan 
has stopped. After checking the POWER/STANDBY indicator, disconnect 
the power cord from the projector and wait for all of the projector’s 
indicators to go out. Next, reconnect the power cord and turn projector 
power back on.
If the error occurs again when you turn power back on, contact your 
retailer or nearest authorized CASIO Service Center. STATUS : Amber flashing
(0.5-second interval)
POWER : Red steady Power has turned off automatically due to a system problem. After 
confirming that the POWER/STANDBY indicator is lit red (without 
flashing), disconnect the power cord from the projector and wait for all of 
the projector’s indicators to go out. Next, reconnect the power cord and 
turn the projector back on.
If the error occurs again when you turn power back on, contact your 
retailer or nearest authorized CASIO Service Center. STATUS : –
POWER : Red steady The projector was turned off automatically due to some problem that was 
probably caused by external digital noise or some other reason. Confirm 
that the POWER/STANDBY indicator is lit red (without flashing). After 
checking the POWER/STANDBY indicator, disconnect the power cord 
from the projector and wait for all of the projector’s indicators to go out. 
Next, reconnect the power cord and turn projector power back on.
If the error occurs again when you turn power back on, contact your 
retailer or nearest authorized CASIO Service Center. STATUS : Red steady
Message : – 
						

							70
Check the following items whenever you experience any problem with the projector.
POWER : Red steady The projector was turned off automatically because the light source unit 
turned off or did not turn on. After confirming that the POWER/STANDBY 
indicator is lit red (without flashing), unplug the power cord. Wait for a 
short while and then plug it back in and turn on the projector again.
If the error occurs again when you turn power back on, contact your 
retailer or nearest authorized CASIO Service Center. STATUS : Red flashing
(0.5-second interval)
Message : –
POWER : Red steady Power has turned off automatically due to a projector memory error. 
Confirm that the POWER/STANDBY indicator is lit red (without flashing). 
After checking the POWER/STANDBY indicator, disconnect the power 
cord from the projector and wait for all of the projector’s indicators to go 
out. Next, reconnect the power cord and turn projector power back on.
If the error occurs again when you turn power back on, contact your 
retailer or nearest authorized CASIO Service Center. STATUS : Red flashing
(2-second or 1-second 
interval)
Message : –
Projector Troubleshooting
ProblemCause and Recommended Action
Power does not turn on.If the POWER/STANDBY indicator is not lit, the AC power cord is not connected 
correctly. Connect the AC power cord correctly.
If the POWER/STANDBY indicator is lit red and the STATUS indicator is lit (or 
flashing) red or amber, it means some type of error has occurred. See “Error 
Indicators and Warning Messages” (page 69).
No image is projected or 
the projected image is 
abnormal.The computer or video device connected to the projector is not turned on or it is 
not outputting a video signal. Make sure the connected computer or video device 
is turned on, and perform the required operation on it to output a video signal.
The correct output source is not selected on the projector. On the projector, select 
the correct input source that corresponds to the connected device.
Images may not project correctly when you have the component output terminal of 
a video device connected to the COMPUTER terminal of the projector.
Image color or display is 
very abnormal.The wrong option (“Component” or “RGB”) may be selected for the “Input Settings  
COMPUTER Terminal” setting on the setup menu. The image will not be projected 
correctly if “Component” is selected while the projector’s COMPUTER terminal is 
connected to the RGB output terminal of a computer, or if “RGB” is selected while the 
projector’s COMPUTER terminal is connected to the component video output 
terminal of a video device. On the setup menu, select “Auto” for the “Input Settings  
COMPUTER Terminal” setting. See page 28.
I can’t understand 
messages or menus 
because they are the 
wrong language.Perform the following operation to select the language you want. See page 29.
1. Press the [MENU] key to display the setup menu.
2. If the input signal is HDMI (PC), press [] four times and then press the [ENTER] 
key. If the input signal is not HDMI (PC), press [] five times and then press the 
[ENTER] key.
3. Press [] twice and then press the [ENTER] key to display the language selection 
menu.
4. Use the [] and [] keys to move the highlighting to the language you want to 
select and then press the [ENTER] key.
5. Press the [MENU] key to exit the setup menu.
Indicator/Error MessageDescription and Required Action